ATTINY416-SFR 20MHz 4KB Flash AVR MCU | Microchip (Tape & Reel)
Teilenummer: ATTINY416-SFR ✓ AktivATTINY416-SFR Übersicht
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, working data memory, input/output ports, and peripherals on one device. The tinyAVR family occupies the low-power, resource-conscious segment of the broader 8-bit microcontroller market. These devices are commonly used for local sensing, actuator control, communication interfaces, and compact products in which deterministic control and low system complexity matter more than processing throughput.
The ATTINY416-SFR provides 4 KB of in-system reprogrammable Flash, 256 B of SRAM, and 128 B of EEPROM. According to the Microchip ATtiny416/ATtiny816 datasheet, the ATTINY416 Flash is organized as 4K by 16 because all AVR instructions are either 16 or 32 bits wide. The processor can operate at up to 20 MHz, while the ATTINY416-SFR is specified by Microchip as a 16 MHz industrial-temperature device in the 20-pin SOIC configuration.
Its integrated peripherals support general-purpose control without requiring a separate programmable logic device. The event system allows hardware-generated events to trigger peripheral actions, reducing dependence on CPU polling. SleepWalking permits selected peripherals to wake or continue activity while the core sleeps. These features are useful in low-power products that must respond quickly to external activity without maintaining a continuously active CPU.
Typical applications include compact industrial controllers, sensor-hub and condition-monitoring nodes, building and appliance control modules, low-power consumer products, and small motor or actuator-control systems. The combination of event-driven peripherals, serial interfaces, analog resources, and low-power modes makes the device suitable for designs that balance responsiveness, deterministic timing, and compact board area.
A key design consideration is that software, peripheral configuration, clock settings, and pin multiplexing must be coordinated before the design reaches prototype testing. UPDI programming and a separate programming interface should be laid out with test-point access, while unused pins should be terminated according to the final board configuration. Temperature, voltage, and decoupling requirements should follow the manufacturer datasheet and selected package details.
This page organizes the manufacturer's device information, distributor listings, and package-oriented comparison information into an engineering-focused resource. It also identifies the limited drop-in substitution landscape, highlights functional differences among related AVR devices, and provides application and design guidance for evaluating the ATTINY416-SFR in embedded systems.
Drop-in-Alternativen für ATTINY416-SFR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATTINY416-SFR (gleiche Bauform und Footprint) – abweichend in Product Type.
ATTINY816-SF
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →ATTINY1616-SF
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
ATTINY416-SFR Grenzwerte & elektrische Eigenschaften
| Product Type | 8-bit AVR tinyAVR 1 functional-safety microcontroller |
| Maximale Taktfrequenz | 20 MHz |
| Distributor Rated Clock | 16 MHz |
| Flash Memory | 4 KB |
| Flash Organization | 4K x 16 |
| SRAM | 256 B |
| EEPROM | 128 B |
| Processor Core | 8-bit AVR with hardware multiplier |
| Gehäuse | 20-pin SOIC |
| Package Suffix | SF |
| Temperature Grade | Industrial, 125 °C |
| Program Memory Type | In-system reprogrammable Flash |
| Architecture | tinyAVR 1 |
| Event System | Yes |
| SleepWalking | Yes |
| Analog Features | Accurate analog features |
ATTINY416-SFR sf Pinbelegungsleitfaden
Pinbelegung für ATTINY416-SFR (sf-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATTINY416-SFR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATTINY416-SFR ist geeignet für 6 Anwendungs: Industrial Sensor and Condition Monitoring, Compact Appliance Control Module, Building Control and Smart Sensor Interface, Low-Power Actuator Controller, Embedded Control and Rapid Prototyping, Small Motor and Relay Interface Control.
Industrial Sensor and Condition Monitoring
The ATTINY416-SFR fits compact sensor nodes that combine an 8-bit AVR controller, 4 KB of Flash, and low-power peripherals in a 20-pin SOIC. Its 20 MHz maximum clock provides sufficient control bandwidth for sampling, filtering, threshold evaluation, and local status handling, while the event system can connect external events to peripheral actions without continuous polling. SleepWalking is valuable in duty-cycled monitors because selected activity can trigger processing while the CPU remains in a low-power state. Design the analog input conditioning around the device's specified ADC and pin limits, and validate the standby and active currents with the complete sensor load attached.
Empfohlen
Compact Appliance Control Module
The ATTINY416-SFR is well suited to appliance subassemblies that coordinate buttons, indicators, relays, and safety-related logic in a small board area. Its 4 KB of in-system-reprogrammable Flash supports compact embedded firmware, and the hardware-multiplier-equipped 8-bit AVR core can handle control logic efficiently. The 20-pin SOIC package provides a conventional, inspectable assembly format and allows analog or timer functions to be assigned alongside digital I/O. For motor or relay loads, keep switching transients away from sensitive traces, use appropriate driver circuitry, and test firmware behavior across all sensor and actuator fault states.
Empfohlen
Building Control and Smart Sensor Interface
The ATTINY416-SFR can serve as a local controller in building-control equipment, receiving commands and converting sensor inputs into actuator or communication outputs. The AVR core runs at up to 20 MHz, allowing responsive digital control, while the event system can reduce latency between peripheral events and firmware responses. Its advanced peripherals support efficient implementation of timers, serial communication, and analog signal conditioning within one controller. Choose the external interface and connector scheme with serviceability in mind, and apply the manufacturer's decoupling and layout guidance to prevent long control or communication lines from coupling noise into sensitive measurements.
Empfohlen
Low-Power Actuator Controller
The ATTINY416-SFR is appropriate for battery-operated actuator controllers where processing must be coordinated with limited energy availability. The event system can connect timer, comparator, or other peripheral events to control actions, reducing software polling, while SleepWalking can support designs that wake the CPU from a low-power state. With 256 B of SRAM and 128 B of EEPROM, the device handles compact control state and persistent configuration without an external memory component. Validate battery life using the actual actuator duty cycle because solenoid, relay, and communication circuits can consume more energy than the MCU itself.
Empfohlen
Embedded Control and Rapid Prototyping
The ATTINY416-SFR supports educational prototypes and compact embedded-control experiments because it combines a familiar 8-bit AVR architecture with 20 MHz maximum clock performance and a standard 20-pin SOIC package. Its 4 KB of Flash is sufficient for small sensing, timing, and actuator-control demonstrations, while the advanced peripheral set enables event-driven designs without excessive polling. Provide programming access through the interface specified in the manufacturer datasheet and include a labeled programming header or test points so firmware can be updated after assembly. For final deployment, reassess package, temperature grade, and production requirements.
Empfohlen
Small Motor and Relay Interface Control
The ATTINY416-SFR can coordinate timing, sensing, and interlocks in small motor or relay-control boards. Its timer and event resources allow firmware to schedule deterministic switching sequences, while the 8-bit processor handles command decoding and state management. The 20-pin SOIC package leaves room for dedicated driver, protection, and interface circuitry around the controller. Keep high-current paths physically separated from sensitive analog inputs, include appropriate flyback protection, and verify startup, shutdown, overload, and stalled-load behavior. The MCU's operating limits do not replace protection design for the connected load.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATTINY416-SFR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATTINY816-SF | ATTINY1616-SF |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC |
| Product Family | tinyAVR 1 | tinyAVR 1 | tinyAVR 1+ |
Wichtigste Unterscheidungsmerkmale
- Family-compatible path to double the available Flash (vs. ATTINY816-SF)
- 20 MHz maximum operating speed for responsive embedded control (vs. ATTINY104F-SSFR)
- Event-driven and low-power architecture for compact control (vs. ATTINY104F-SSFR)
Designhinweise
Place the device power pins, decoupling capacitors, ground connection, and programming interface exactly as directed by the manufacturer package drawing and pin-description tables. Route analog inputs away from switching-node and relay-driver traces, and keep the return path for analog ground short and continuous. A compact SOIC footprint does not justify long decoupling loops, because those loops can undermine the low-noise behavior expected from the tinyAVR analog resources.
Budget the power system around both active and sleep states rather than a single nominal current value. The MCU's sleep current, active current, I/O loading, and external sensor load must be combined over the real operating duty cycle. If an actuator is connected, include its startup and hold current in the calculation and provide protection that prevents an overloaded or stalled load from pulling the MCU rail outside its operating limits.
Do not approve a substitute solely because it is labeled tinyAVR or uses a 20-pin SOIC. Compare flash organization, SRAM and EEPROM capacity, clock limits, power pins, programming signals, peripheral multiplexing, and analog functions. The ATTINY816-SF has twice the Flash of the ATTINY416-SFR, while the ATTINY1616-SF uses a different memory architecture; either change can affect firmware layout, startup code, and board assumptions even when the package outline appears similar.
Design the programming connector or pogo-fixture pads before routing the final PCB. Maintain short, repeatable access to the programming interface and avoid placing tall components or enclosure hardware over those pads. For low-power products, verify that floating inputs and unused pins cannot create unintended current paths, and use the datasheet's recommended configurations to prevent an unused input from oscillating and increasing system consumption.
Compliance-Informationen
Mouser identifies ATTINY416-SFR as green and industrial temperature grade, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified. The part is not presented as an automotive-qualified AEC-Q100 device.