ATXMEGA64A1-AU - 32MHz 64KB Flash MCU | Microchip Technology
Teilenummer: ATXMEGA64A1-AU ✓ AktivATXMEGA64A1-AU Übersicht
An 8/16-bit microcontroller is a programmable semiconductor that integrates a CPU, nonvolatile program memory, data memory, interrupt handling, and peripherals into one device. The ATXMEGA64A1-AU belongs to the AVR XMEGA family, which extends the AVR architecture into a higher-performance 8/16-bit platform with simultaneous operation of two 16-bit registers and hardware accelerators for data movement and event routing.
The 64 KB Flash program memory includes a 4 KB boot-code section and supports read-while-write operation. Internal memory is completed by 4 KB of SRAM and 2 KB of EEPROM. Peripheral integration includes four-channel DMA, an eight-channel event system, 78 general-purpose I/O lines, a 16-bit real-time counter, and eight flexible 16-bit timer/counter modules with compare and PWM channels. These resources reduce external logic and improve responsiveness in embedded control designs.
The enhanced AVR RISC architecture executes instructions in a single clock cycle and delivers throughput approaching 1 MIPS per MHz. Its integrated peripherals can transfer data without repeated CPU intervention, while the event system connects timer, comparator, ADC, and other peripherals through configurable event channels. The ATXMEGA64A1-AU therefore supports responsive embedded control without requiring a separate DSP or high-speed external bus interface for many common tasks.
Typical uses include industrial automation controllers, data acquisition systems, motor-control and PWM platforms, communications equipment, and connected sensor nodes. The device is particularly useful when a design needs more peripheral capacity and processing throughput than a small 8-bit MCU, while retaining the familiar AVR development ecosystem and integrated on-chip memories.
PCB implementation should preserve the manufacturer's recommended power, clock, decoupling, programming, and signal-routing arrangements. The 100-lead TQFP footprint requires careful escape routing around the device, while the 1.6 V to 3.6 V operating range requires attention to regulator tolerance, signal levels, and load-dependent voltage droop.
This product page organizes the core device specifications, package information, design considerations, application guidance, and pin-compatible family alternatives into a single engineering reference for MCU selection and board design.
Drop-in-Alternativen für ATXMEGA64A1-AU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATXMEGA64A1-AU (gleiche Bauform und Footprint) – abweichend in Package, Boot Code Section, DMA Channels, Event System Channels, ADC.
ATXMEGA64A1U
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATXMEGA64A2-AU
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
ATXMEGA64A3-AU
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →ATXMEGA64A4-AU
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
ATXMEGA128A1-AU
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →ATXMEGA64A1-AU Grenzwerte & elektrische Eigenschaften
| Product Type | 8/16-bit AVR XMEGA A1 microcontroller |
| Maximum Clock Speed | 32 MHz |
| Flash Program Memory | 64 KB (32K x 16) |
| Boot Code Section | 4 KB |
| SRAM | 4 KB |
| EEPROM | 2 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| DMA Channels | 4 channels |
| Event System Channels | 8 channels |
| General-Purpose I/O Lines | 78 lines |
| Reported I/O Port Count | 34 |
| Real-Time Counter | 16-bit |
| Timer/Counter Modules | 8 flexible 16-bit timer/counters |
| CPU Architecture | AVR enhanced RISC, 8/16-bit |
| Gehäuse | 100-lead TQFP, 14 mm x 14 mm |
| Montageart | Surface mount |
| Program Memory Type | Flash |
| In-System Programming | Supported |
| Read-While-Write | Supported |
| Programmable Multilevel Interrupt Controller | Supported |
| External Bus Interface | Supported |
ATXMEGA64A1-AU 100-lead tqfp, 14 mm x 14 mm Pinbelegungsleitfaden
Pinbelegung für ATXMEGA64A1-AU (100-lead tqfp, 14 mm x 14 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATXMEGA64A1-AU.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATXMEGA64A1-AU ist geeignet für 6 Anwendungs: Industrial Automation Controllers, Industrial Data-Acquisition Systems, Motor Control and PWM Platforms, Communications Equipment, Connected Sensor Nodes, Programmable Logic and Test Equipment.
Industrial Automation Controllers
The ATXMEGA64A1-AU fits industrial automation controllers that combine multiple discrete inputs, actuator outputs, timing functions, and local communication. Its 78 general-purpose I/O lines provide substantial board-level integration in a 100-lead TQFP package, while eight 16-bit timer/counters support pulse measurement, interval timing, and PWM generation. The four-channel DMA controller can move data between peripherals and SRAM with less CPU intervention, and the eight-channel event system can coordinate timing-sensitive events. At 32 MHz, the AVR enhanced RISC core also provides the processing headroom required for protocol stacks and control logic. Engineers should still allocate appropriate isolation, surge protection, grounding, and safety margins for factory-connected equipment.
Empfohlen
Industrial Data-Acquisition Systems
The ATXMEGA64A1-AU is suitable for compact data-acquisition equipment that must combine timed analog measurements, local buffering, control outputs, and communications in one controller. Its 32 MHz core supports deterministic sampling and signal processing, while 4 KB of SRAM and 2 KB of EEPROM provide working and nonvolatile storage beyond the 64 KB Flash program area. DMA can transfer sampled or serial data efficiently, and the event system can coordinate ADC activity, timers, and external triggers. Use the device's multiplexed I/O only after mapping analog, communications, and debug functions to specific pins. Board-level reference quality, input protection, analog filtering, isolation, and calibration ultimately determine measurement accuracy.
Empfohlen
Motor Control and PWM Platforms
The ATXMEGA64A1-AU supports motor-control and PWM platforms where multiple timing outputs, feedback inputs, and control computations must operate together. Its eight flexible 16-bit timer/counters include compare and PWM channels, enabling several motor axes, gate-drive sequences, or synchronized half-bridge outputs. The event system can connect timer events directly to other peripherals, reducing latency and CPU workload, while DMA supports efficient movement of position, speed, or current-control data. The 78 GPIO lines provide flexibility for encoders, fault inputs, and control signals. The MCU does not replace power electronics: designers still need suitable gate drivers, current sensing, overcurrent protection, thermal management, and appropriate grounding for the power stage.
Empfohlen
Communications Equipment
The ATXMEGA64A1-AU can serve as the control processor in communications equipment where a low-power 8/16-bit MCU must manage a protocol stack, local user interface, and hardware peripherals. Its 32 MHz execution rate, 64 KB Flash, and 4 KB SRAM are useful for embedded protocol handling, while the timer/counter and event resources support baud-rate timing and synchronized data movement. The extensive GPIO count allows connection of UART, SPI, I2C, and status signals without excessive multiplexing. Interface voltage levels and signal conditioning must be handled externally when connected to optocouplers, transceivers, or line drivers. Firmware should use the manufacturer pin-muxing definitions and validate timing against the selected communication standard.
Empfohlen
Connected Sensor Nodes
The ATXMEGA64A1-AU is appropriate for connected sensor nodes that combine local sensing, digital filtering, event handling, and a low-power communications link. Its internal Flash stores firmware, SRAM supports working buffers, and EEPROM preserves configuration or calibration values. The event system and DMA controller allow sensors, timers, and communication blocks to exchange information with reduced processor involvement, which is beneficial in periodic acquisition systems. Low-power operation still depends on the selected clock mode, peripheral activity, and board leakage, so sleep-mode requirements should be measured on the finished assembly. Sensor excitation, signal conditioning, protection, and radio isolation are separate analog and RF design tasks.
Empfohlen
Programmable Logic and Test Equipment
The ATXMEGA64A1-AU can serve as the supervisory controller in programmable test and measurement equipment where sequencing, limits, logging, communications, and user control must be coordinated. Eight 16-bit timer/counters support precise stimulus timing and measurement windows, while DMA accelerates transfer of results and status information. The 64 KB Flash supports substantial control firmware, and 2 KB of EEPROM can retain setup values across power cycles. For precision analog measurement, external references, ADC devices, op-amps, and protection networks are generally required because the MCU is primarily a digital controller. Layout must separate sensitive analog and high-current paths from digital clocks and switching nodes to avoid measurement errors.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATXMEGA64A1-AU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATXMEGA64A1U | ATXMEGA64A2-AU | ATXMEGA64A3-AU | ATXMEGA64A4-AU | ATXMEGA128A1-AU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100, 14 mm x 14 mm | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 |
| Maximum Clock Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 64 KB | 64 KB | 128 KB | 128 KB | 256 KB | 128 KB |
| EEPROM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| DMA Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Event System Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| General-Purpose I/O Lines | 78 lines | Up to 32 I/O pins listed on the product page | 78 lines | 78 lines | 78 lines | 78 lines |
| Timer/Counter Modules | 8 flexible 16-bit timer/counters | 8 flexible 16-bit timer/counters | 8 flexible 16-bit timer/counters | 8 flexible 16-bit timer/counters | 8 flexible 16-bit timer/counters | 8 flexible 16-bit timer/counters |
Wichtigste Unterscheidungsmerkmale
- Provides the complete 78-line GPIO resource set in the target device (vs. ATXMEGA64A1U)
- Matches the target Flash capacity without requiring a larger memory device (vs. ATXMEGA64A4-AU)
- Supports firmware growth without changing to the 128 KB Flash member (vs. ATXMEGA128A1-AU)
Designhinweise
Design the 1.6 V to 3.6 V supply rail so that its tolerance, startup ramp, and transient response remain acceptable during Flash programming and maximum peripheral activity. Place the required bypass capacitors at the corresponding power pins and keep the return-current path short. Verify regulator output against the MCU operating limits and avoid routing high-current outputs through the same narrow copper region used by sensitive analog or crystal circuitry.
Assign every connection from the manufacturer pin-description table because the 100-lead TQFP pinout combines GPIO, alternate peripheral functions, debug signals, analog inputs, clocks, and power pins. Maintain the manufacturer's recommended footprint dimensions and land pattern rather than relying on a generic TQFP drawing. Check pin multiplexing in the final firmware and schematic, particularly for communications, timers, ADC functions, and programming signals.
Route clock and high-speed communication signals as controlled-impedance nets where applicable, and keep switching or motor-drive nodes away from ADC and crystal inputs. Provide a solid ground plane, minimize loop area in power paths, and use dedicated return paths beneath high-current switching interfaces. Place external crystals or resonators and their load components close to the device, following the layout guidance in the manufacturer datasheet.
Do not assume that identical TQFP outlines guarantee a drop-in replacement. A valid substitution must match package dimensions, pin multiplexing, memory requirements, peripheral resources, clock behavior, voltage limits, and temperature range. Also verify programming, boot, reset, and debug functions before releasing an alternate MPN for production. Firmware built for the original device should be regression-tested with every selected alternative.
Compliance-Informationen
Compliance status must be confirmed for the exact ordering code from the manufacturer's product documentation.
