BD37503FV-E2 2-Band I2C Audio Processor | ROHM Semiconductor
Teilenummer: BD37503FV-E2 ✗ AbgekündigtBD37503FV-E2 Übersicht
An analog sound processor is an audio special-purpose integrated circuit that adjusts or conditions audio signals between source selection, amplification, and the speaker system. Within the signal chain, it belongs to the broader hierarchy of audio signal-processing IC, audio interface IC, and semiconductor. The BD37503FV-E2 combines channel selection, bass and treble equalization, loudness compensation, and output filtering in one dedicated analog device, reducing the number of separate control blocks required in a compact audio design.
The two-band equalizer provides independent low-frequency and high-frequency tone controls. The built-in four-input selector supports connecting several audio sources, while the differential input selector permits combinations of single-ended and differential inputs. Switchable loudness processing adds a tonal contour intended for low-volume listening, and the selectable second-order anti-aliasing filter attenuates noise that can occur at the output of a DAC. These functions are controlled through the device's I2C interface.
The 7 V to 9.5 V operating range places the part in systems using an approximately 8 V audio bus. Because this is an analog processor rather than a digital signal processor, its behavior is governed by the internal filter and selector circuitry rather than software-defined signal paths. The I2C control interface allows a host controller to adjust the operating configuration without dedicating separate analog switches to every function. Exact filter coefficients, control-register values, frequency response points, and signal-to-noise figures must be established from the manufacturer datasheet before final circuit tuning.
Typical uses include compact consumer-audio systems, multimedia equipment, car-audio interfaces, active speakers, and equipment that accepts multiple analog audio sources. In each case, the BD37503FV-E2 can provide centralized source selection and tone shaping before the selected signal reaches an audio amplifier. Its integrated filtering is particularly useful when a DAC output requires selectable attenuation of out-of-band or switching-related noise.
The primary design consideration is signal integrity. Keep analog traces short, provide a low-impedance return path, decouple the supply near the device, and isolate the audio path from switching nodes and high-current amplifier outputs. Confirm that the selected input, filter, and equalizer settings remain valid for the source level and intended speaker crossover behavior rather than assuming that bass, treble, and loudness controls can compensate for incorrect gain staging.
This page consolidates the confirmed operating features, package information, application guidance, and sourcing structure for the BD37503FV-E2. It is intended to help engineers evaluate the device against the functional requirements of a multi-source analog audio system before checking the complete pin, register, and electrical tables in the ROHM datasheet.
Drop-in-Alternativen für BD37503FV-E2 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernBD37503FV-E2 Grenzwerte & elektrische Eigenschaften
| Product Type | Analog sound processor with built-in two-band equalizer |
| Betriebsversorgungsspannung | 7 V to 9.5 V |
| Control Interface | I2C bus |
| Input Selector | 4 inputs |
| Input Configuration | Single-ended and differential input combinations |
| Equalizer | 2-band, bass and treble |
| Loudness Filter | Switchable |
| Anti-Aliasing Filter | Second-order, switchable |
| Anti-Aliasing Filter Purpose | Attenuates noise occurring at DAC output |
| Gehäuse | 20-pin SSOP |
| Montageart | Surface mount |
| Anzahl der Pins | 20 pins |
| Audio Processing Functions | Input selection, bass, treble, loudness, and anti-aliasing filtering |
BD37503FV-E2 20-pin ssop Pinbelegungsleitfaden
Pinbelegung für BD37503FV-E2 (20-pin ssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für BD37503FV-E2.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
BD37503FV-E2 ist geeignet für 6 Anwendungs: Multi-Source Consumer Audio, DAC Output Noise Filtering, Active Speaker Tone Control, Automotive Audio Interface, Portable Multimedia Audio, Industrial Audio Control Panel.
Multi-Source Consumer Audio
The BD37503FV-E2 fits compact consumer-audio products that must accept several analog sources and apply common tone control before amplification. Its four-input selector reduces the need for separate analog routing components, while the two-band equalizer provides electronic bass and treble adjustment. The 7 V to 9.5 V operating range supports an approximately 8 V audio architecture, and I2C control allows a system processor to configure source and filtering functions without external potentiometers. Designers should establish the input gain structure before enabling loudness, because loudness and equalizer settings interact when source levels vary.
DAC Output Noise Filtering
The switchable second-order anti-aliasing filter makes the BD37503FV-E2 useful between a DAC and the downstream audio path when the design needs selectable attenuation of noise occurring at DAC output. Keeping this filtering in the sound processor can simplify centralized audio routing while allowing the filter to be enabled according to the active source. Evaluation should compare the filtered and unfiltered paths for the actual DAC, sample rate, clock arrangement, and signal amplitude. The device should not be treated as a universal replacement for a DAC's digital reconstruction filter; its role is analog post-processing within the selected signal chain.
Active Speaker Tone Control
In an active speaker or compact amplified speaker, the BD37503FV-E2 can provide a shared analog conditioning stage for bass, treble, loudness, and source selection before power amplification. Placing these functions in a dedicated sound processor keeps the signal chain configurable while limiting discrete analog-control complexity. Its 20-pin SSOP package supports conventional surface-mount assembly, and I2C control permits settings to be stored or adjusted by the product controller. The design must maintain suitable signal levels into the amplifier and avoid using tone controls to compensate for poor crossover design or inadequate headroom.
Automotive Audio Interface
The BD37503FV-E2 can serve as the analog audio conditioning element in a vehicle audio interface that combines radio, navigation, auxiliary, or media sources. Four-input selection, differential-input support, and centralized bass and treble adjustment are useful in such systems, while loudness processing can improve perceived response at reduced listening levels. The 7 V to 9.5 V operating range must align with the vehicle's audio supply architecture. Before production use, verify operating-temperature range, load-dump behavior, ESD protection, electromagnetic compatibility, and automotive qualification requirements directly with ROHM.
Portable Multimedia Audio
A portable multimedia device can use the BD37503FV-E2 when analog program audio, media audio, and auxiliary sources must be selected and equalized before amplification. The I2C interface enables the host controller to switch routes and adjust the two-band equalizer, while the separate loudness and anti-aliasing functions can be enabled for listening modes or source-specific behavior. The approximately 8 V operating range requires a supply that remains within 7 V to 9.5 V across all battery and system conditions. Board-area constraints should also account for the 20-pin SSOP footprint, decoupling, filtering, and return-path routing.
Industrial Audio Control Panel
The BD37503FV-E2 is suitable for industrial audio equipment that accepts several analog sources and requires repeatable electronic tone adjustment without front-panel potentiometers. Source selection and filter configuration can be handled through I2C, simplifying panel operation and allowing operating modes to be stored by a supervisory controller. The integrated loudness filter can provide an alternate listening contour, while the selectable second-order anti-aliasing stage can be used when the source is a DAC with unwanted high-frequency content. Industrial deployment still requires validation of temperature, immunity, ESD, and supply-transient requirements.
Technische Referenzdaten für BD37503FV-E2 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 20-pin SSOP |
| Brand | ROHM Semiconductor |
| Product Type | Analog sound processor |
| Operating Supply Voltage | 7 V to 9.5 V |
| Control Interface | I2C bus |
| Input Selector | 4 inputs |
| Equalizer Bands | 2 bands: bass and treble |
| Loudness Filter | Switchable |
| Anti-Aliasing Filter | Switchable second-order filter |
| Input Configuration | Single-ended and differential input combinations |
Wichtigste Unterscheidungsmerkmale
- Consolidates multiple analog sound-processing functions (vs. A discrete four-input selector, two-band equalizer, loudness filter, and anti-aliasing network)
- Supports programmable source and filter control (vs. A manually adjusted analog tone-control circuit)
- Offers selectable post-DAC filtering (vs. An unfiltered DAC-to-amplifier signal path)
Designhinweise
Keep the analog input, output, and filter paths compact and route them away from switching-node copper, inductors, high-current amplifier outputs, and digital clock lines. Use a continuous ground reference beneath the audio section and place the supply bypass capacitor close to the device power pins. The I2C traces should be short and isolated from sensitive audio inputs. Preserve the package land pattern and verify the exposed connections and pin numbering against the manufacturer footprint drawing before releasing the PCB files.
Establish the source gain structure before applying bass, treble, or loudness processing. The equalizer and loudness filters can alter the apparent level of individual frequency ranges, so incorrect upstream gain may cause clipping or make the loudness function ineffective. Evaluate each input with the selected equalizer and filter settings, and place any required attenuation or gain control ahead of the BD37503FV-E2. Confirm the full filter response and control resolution using the manufacturer frequency-response and register tables.
Design the supply for a steady operating range of 7 V to 9.5 V, including startup, load transitions, and tolerance. Place local high-frequency decoupling at the power pins and separate the audio supply path from noisy digital or switching-converter currents where the board architecture permits. Verify the device's permitted supply sequencing and absolute maximum limits in the manufacturer electrical tables. Do not infer a maximum transient or absolute maximum voltage from the normal operating range alone.
Do not select a generic amplifier, codec, or digital equalizer as a direct substitute merely because it also controls audio. A valid replacement must retain the 20-pin SSOP footprint, pin-to-pin connectivity, 7 V to 9.5 V supply compatibility, I2C register behavior, four-input selector, equalizer, loudness path, and anti-aliasing function. Likewise, do not assume the second-order anti-aliasing filter replaces a DAC reconstruction filter; validate it against the actual DAC output spectrum and operating mode.
Compliance-Informationen
Compliance and qualification attributes are not stated in the available product records. The -E2 ordering suffix alone is not treated as proof of RoHS, REACH, AEC-Q100, lead-free, or halogen-free status.