BT136-600D,127 - 4A 600V Sensitive Gate TRIAC | WeEn Semiconductors
Teilenummer: BT136-600D,127 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0.55 | $0,55 |
| 10 | $0.48 | $4,80 |
| 100 | $0.39 | $39,00 |
| 500 | $0.33 | $165,00 |
| 1.000 | $0.28 | $280,00 |
BT136-600D,127 Übersicht
A TRIAC (triode for alternating current) is a bidirectional thyristor that conducts in both halves of an AC waveform, effectively functioning as two SCRs wired in anti-parallel within a single die. It belongs to the thyristor family within discrete power semiconductors, used wherever AC mains must be switched or phase-controlled by a low-power control signal. TRIACs sit in the hierarchy: thyristor -> discrete semiconductor -> power device. The four-quadrant symmetric gating of the "D" series enables the same low gate drive to fire the device in Quadrants I, II, III, and IV, simplifying MCU-driven phase-control and zero-cross switching designs.
Key specifications include 600 V repetitive peak off-state voltage (VDRM), 4 A RMS on-state current (IT(RMS)), 25 A non-repetitive surge current (ITSM), 10 mA maximum gate trigger current (IGT), 1 V maximum gate trigger voltage (VGT), and 5 W power dissipation (PG(AV)). The TO-220AB package exposes a metal tab that doubles as the main terminal (MT2) and serves as a heatsink mounting interface. Planar passivated die construction yields stable blocking characteristics and long-term reliability under thermal cycling.
Typical applications include AC lamp dimmers (leading-edge phase control), fan and small motor speed regulators, solid-state relays, heater control, and general-purpose AC switching in white goods. Logic-level IGT allows direct drive from microcontroller GPIO pins, eliminating the need for a dedicated gate driver circuit.
Drop-in-Alternativen für BT136-600D,127 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
BT136-600D/DG,127
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
BT136-600E,127
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
T405-600B
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
BT137-600E,127
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
BTA04-600TRG
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
L4004L5
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
BT136-600D,127 Technische Daten
| Thyristor Type | TRIAC - Logic Level, Sensitive Gate |
| Operating Quadrants | 4 (Q1, Q2, Q3, Q4) |
| Repetitive Peak Off-State Voltage (VDRM) | 600 V |
| RMS On-State Current (IT(RMS)) | 4 A |
| Non-Repetitive Surge Current (ITSM) | 27 A |
| Maximum Gate Trigger Current (IGT) | 10 mA |
| Maximum Gate Trigger Voltage (VGT) | 1 V |
| Average Power Dissipation (PG(AV)) | 5 W |
| Gehäuse | TO-220AB (SOT78 / SC-46), 3 pins + tab |
| Montageart | Through Hole |
| Pin-Anzahl | 3 |
| Configuration | Single TRIAC, isolated tab |
| Technology | Planar passivated silicon die |
| RoHS-Status | Compliant |
BT136-600D,127 Pin-Konfiguration
| Pin 1 | MT1 — Main Terminal 1 (reference for gate and MT2) |
| Pin 2 | MT2 — Main Terminal 2 (also tied to metal tab) |
| Pin 3 | G — Gate trigger input |
On-State Current vs Voltage Drop
Typische Anwendungen
BT136-600D,127 ist geeignet für 6 Anwendungs: AC Lamp Dimmer (Leading-Edge Phase Control), Fan and Small Motor Speed Controller, Solid-State Relay (SSR) Output Stage, White Goods Heater Control, General-Purpose AC Switching for Appliances, Industrial Solenoid and Contactor Driver.
AC Lamp Dimmer (Leading-Edge Phase Control)
The BT136-600D,127 drives 120/230 V AC incandescent and dimmable LED loads at up to 4 A RMS with 10 mA IGT, matching low-power microcontroller GPIO or optocoupler (MOC3041) gate drive. In a typical leading-edge dimmer, the TRIAC fires after a delay set by an RC network synchronized to the AC zero-cross, and the device's 600 V VDRM provides a 2x safety margin over 230 V mains. Unlike a mechanical potentiometer-rheostat dimmer, this TRIAC dissipates only millwatts during the dimming cycle, keeping the housing cool.
Empfohlen
Fan and Small Motor Speed Controller
The BT136-600D,127 controls shaded-pole and permanent-split-capacitor AC fan motors up to 4 A by phase-angle modulation of the mains voltage. Its 4-quadrant sensitive gate accepts low-current drive from a wall-mounted speed-control circuit, and its 27 A ITSM rating handles motor inrush during start-up. The TO-220AB tab is bolted to an aluminum heatsink to dissipate the 5 W worst-case PG(AV) at full phase delay, ensuring junction temperature stays within safe limits.
Empfohlen
Solid-State Relay (SSR) Output Stage
The BT136-600D serves as the switch element in PCB-mount solid-state relays rated up to 4 A at 600 V. Its logic-level 10 mA IGT enables direct drive from opto-isolated logic inputs (3.3 V or 5 V), avoiding secondary-side power supplies in the SSR. The TRIAC's zero-cross or random-fire switching topology determines whether it is used for heater (zero-cross) or motor (random-fire) SSR variants.
Empfohlen
White Goods Heater Control
Washing machines, dishwashers, and electric water heaters use the BT136-600D,127 to switch resistive heater banks up to roughly 920 W at 230 V RMS. The TRIAC's planar passivated junction handles the thermal cycling of repeated on/off heater regulation, and the 10 mA IGT keeps MCU-side design simple. Heater loads are pure resistive, so no snubber is strictly required, but a 100 nF Y-cap across MT1-MT2 improves EMI signature.
Empfohlen
General-Purpose AC Switching for Appliances
Coffee makers, kettles, and small kitchen appliances integrate the BT136-600D,127 to provide soft-start and on/off control of mains-rated heaters. The TO-220AB package's through-hole leads support wave-soldered assembly and accept a clip-on heatsink for higher dissipation applications. The TRIAC's 600 V rating exceeds 230 V mains by 2.5x, ensuring robust blocking margin under transient surges.
Empfohlen
Industrial Solenoid and Contactor Driver
The BT136-600D,127 controls 24-230 V AC solenoids and small contactor coils in industrial automation panels. Its four-quadrant trigger permits AC or DC coil drive, and the 10 mA IGT lets a 24 V PLC output drive the gate via a resistor. The TO-220AB tab mounts to a DIN-rail enclosure heatsink for sustained duty in control cabinets.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für BT136-600D,127 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | BT136-600D/DG,127 | BT136-600E,127 | T405-600B | BT137-600E,127 | BTA04-600TRG |
|---|---|---|---|---|---|---|
| Brand | WeEn Semiconductors | WeEn Semiconductors | WeEn Semiconductors | STMicroelectronics | WeEn Semiconductors | STMicroelectronics |
| Package | TO-220AB | TO-220AB - same | TO-220AB - same | TO-220AB - same | TO-220AB - same | TO-220AB - same |
| VDRM (blocking voltage) | 600 V | 600 V | 600 V | 600 V | 600 V | 600 V |
| IT(RMS) (on-state current) | 4 A | 4 A | 4 A | 4 A | 8 A | 4 A |
| IGT (gate trigger) | 10 mA | 10 mA | 25 mA | 5 mA | 25 mA | 10 mA |
| ITSM (surge) | 27 A | 27 A | 27 A | 30 A | 55 A | 40 A |
| PG(AV) (dissipation) | 5 W | 5 W | 5 W | 5 W | 5 W | 5 W |
| Quadrants | 4 (Q1-Q4) | 4 (Q1-Q4) | 4 (Q1-Q4) | 4 (Q1-Q4) | 4 (Q1-Q4) | 4 (Q1-Q4) |
| Tab connection | MT2 (non-isolated) | MT2 (non-isolated) | MT2 (non-isolated) | MT2 (non-isolated) | MT2 (non-isolated) | Isolated |
Wichtigste Unterscheidungsmerkmale
- Very-sensitive-gate 10 mA IGT in all four quadrants (vs. BT136-600E,127)
- Lower IGT than STMicroelectronics T-series alternatives (vs. T405-600B (STMicroelectronics))
- Higher VDRM than Littelfuse L4 series equivalents (vs. L4004L5 (Littelfuse))
Designhinweise
Estimated: at 4 A IT(RMS) and full 5 W PG(AV) dissipation, the TO-220AB junction-to-ambient thermal resistance of approximately 62.5 C/W yields a 312 C junction-temperature rise above ambient, which is excessive. A clip-on or bolt-on heatsink with thermal resistance below 10 C/W is required for continuous 4 A operation; without a heatsink, derate to roughly 1.5 A continuous on free air.
Place the RC snubber (100 ohm + 100 nF) within 5 mm of MT1-MT2 terminals. Keep the gate-series resistor (100-220 ohm) close to pin 3 to limit high-frequency ringing on the gate drive path. Minimize the gate-cathode loop area to improve dV/dt immunity in noisy AC-line environments such as motor control cabinets.
Do not use the BT136-600D on DC-only loads - a TRIAC cannot commutate off without an AC zero-cross, so once latched in DC operation it will stay on. For DC switching use an SCR or MOSFET. Also avoid exceeding ITSM (27 A) during transformer inrush; pre-charge capacitor banks to limit repetitive peak surge current.
Compliance-Informationen
RoHS and REACH compliance per WeEn product page and distributor listings; AEC-Q100 not applicable for through-hole discrete power TRIACs.
