CD4020BK3 - 14-Bit CMOS Binary Counter | Harris | Logic
Teilenummer: CD4020BK3 ✓ AktivCD4020BK3 Übersicht
A binary counter is a sequential digital circuit that records successive binary values at its clock input. A ripple-carry counter uses cascaded flip-flop stages, with each stage driving the next; this creates a simple, economical implementation with multiple independently accessible count outputs. The CD4020 belongs to the CMOS CD4000 logic family, a hierarchy of low-power digital ICs built around metal-oxide-semiconductor field-effect transistors and widely used for counters, dividers, gates, latches, and timers.
The CD4020 provides 14 count stages, allowing division of an input clock by binary ratios from 2 through 16384. Its negative-edge-triggered clock input advances the count on the falling transition, while a high-level reset input clears the counter to its all-zero state. With a 3 V to 18 V supply range and operation to 24 MHz, the device bridges low-speed industrial timing and higher-speed digital frequency division requirements.
Operation is based on cascaded master-slave stages. When the clock changes from high to low, the first stage toggles and its carry output advances the following stage. The outputs therefore divide the input frequency by successive powers of two. Because propagation delay accumulates through the cascade, the useful operating frequency must remain within the device’s specified timing limits, and unused stages should not be relied upon as zero-delay logic outputs.
Typical applications include divide-by-N clock generation, pulse-rate reduction, programmable timing modules, digital time-base circuits, oscillator counters, sequential control, and industrial pulse-distribution systems. An oscillator supplies the source clock, the CD4020 divides it, and downstream logic selects or gates the divided outputs. The 16-CFP package also supports through-hole assembly and prototype or repair work where surface-mount packages are less convenient.
Designers should use the manufacturer’s pin-description table when assigning PCB tracks and should account for unused output states during startup and reset. Input signal levels must remain within the supply-dependent CMOS limits, and external rise-time control may be needed when driving long traces. Decoupling close to the supply pins reduces supply noise, while careful clock routing limits false transitions and unwanted count advancement.
This page combines the CD4020BK3 function, family-level operating parameters, pin-package guidance, sourcing information, and drop-in comparison with related CD4020 devices. It also identifies the important trade-offs among counter grades and package options so engineers can select a replacement without overlooking voltage, speed, temperature, or footprint constraints.
Drop-in-Alternativen für CD4020BK3 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit CD4020BK3 (gleiche Bauform und Footprint) – abweichend in Logic Family.
CD4020BE
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →CD4020BF3A
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
CD4020BK3 Grenzwerte & elektrische Eigenschaften
| Product Type | 14-bit binary counter and divider |
| Logic Family | CD4000 CMOS |
| Counter Architecture | Ripple-carry |
| Number of Count Elements | 1 element |
| Number of Count Stages | 14 stages |
| Counting Edge | Negative edge |
| Maximale Taktfrequenz | 24 MHz |
| Supply Voltage Range | 3 V to 18 V |
| Gehäuse | 16-CFP |
| Pin-Anzahl | 16 pins |
| Montageart | Through-hole |
| Output Function | Binary counter outputs and frequency division |
| Reset Function | Asynchronous reset to logic zero |
| Maximum Division Ratio | 16384:1 |
| Technology | CMOS |
CD4020BK3 16-cfp Pinbelegungsleitfaden
Pinbelegung für CD4020BK3 (16-cfp-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für CD4020BK3.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
CD4020BK3 ist geeignet für 6 Anwendungs: Programmable Clock Divider, Industrial Pulse Rate Reduction, Digital Timer and Time Base, Oscillator Frequency Divider, Sequential Control Logic, Retrofit and Through-Hole Prototyping.
Programmable Clock Divider
The CD4020BK3 suits clock-divider and time-base designs because its 14 cascaded stages divide an incoming clock by binary ratios from 2 through 16384. Place the oscillator close enough to preserve clock-edge quality, connect the selected Q output to the downstream timing circuit, and assert reset during initialization. The 24 MHz family maximum provides useful margin when the operating supply and trace conditions support it, while 3 V to 18 V operation allows the same divider approach to span several CMOS logic voltages.
Empfohlen
Industrial Pulse Rate Reduction
When a sensor or machine produces more pulses than the receiving controller can process, the CD4020BK3 can reduce that pulse rate through a selected binary stage. Its negative-edge counting behavior makes it useful with common pulse sources, while the 3 V to 18 V supply range supports integration into industrial control logic. The key design consideration is preserving a clean clock edge in noisy environments and verifying that the chosen Q output provides the required reduction without losing pulse events.
Empfohlen
Digital Timer and Time Base
The CD4020BK3 can divide a stable oscillator into slower timing intervals for elapsed-time measurement, delayed events, or repetitive sequencing. Its 14 stages allow a wide range of binary time increments, and the high-impedance reset function clears all stages to zero for repeatable timing periods. For accurate timekeeping, use a low-jitter oscillator and route the clock away from motor, relay, and power-converter switching nodes so edge disturbances do not create false counts.
Empfohlen
Oscillator Frequency Divider
The CD4020BK3 divides an oscillator output into lower-frequency signals while preserving a straightforward CMOS logic implementation. A Q1 output provides divide-by-two behavior, while later outputs provide progressively lower frequencies. The family operates up to 24 MHz and accepts a 3 V to 18 V supply, giving designers flexibility in test and measurement or embedded clock-generation systems. Keep the oscillator output buffered and observe the specified clock transition limits at the selected supply voltage.
Empfohlen
Sequential Control Logic
In a sequential control system, the CD4020BK3 can count command or process pulses and expose multiple progress states through its stage outputs. This allows simple control logic to detect when a binary count has reached a particular threshold without a programmable microcontroller. Because ripple propagation accumulates through the stages, design timing around the relevant counter output rather than assuming every output changes at the same instant. The 16-CFP package is also convenient for through-hole industrial control boards.
Empfohlen
Retrofit and Through-Hole Prototyping
The 16-CFP CD4020BK3 is practical for repair, educational, and legacy-system boards that use through-hole logic packages. Its 14-stage counter provides a simple way to divide pulses without programmable logic or a complex digital IC. During layout, follow the manufacturer pin-description table rather than assuming a generic DIP pinout, and maintain adequate clearance around adjacent through-hole leads. This package choice also simplifies socket-based experimentation and component substitution during maintenance.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für CD4020BK3 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | CD4020BE | CD4020BF3A |
|---|---|---|---|
| Package | 16-CFP | 16-CFP | 16-CFP |
| Brand | Harris Corporation | Texas Instruments | Texas Instruments |
| Counter Function | 14-stage ripple-carry binary counter and divider | 14-stage ripple-carry binary counter and divider | 14-stage ripple-carry binary counter and divider |
| Logic Family | CD4000 CMOS | CD4000 CMOS | CD4000 CMOS |
| Supply Voltage Range | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V |
| Maximum Clock Frequency | 24 MHz | 24 MHz | 24 MHz |
| Counting Edge | Negative edge | Negative edge | Negative edge |
| Counting Elements | 1 element | 1 element | 1 element |
| Maximum Division Ratio | 16384:1 | 16384:1 | 16384:1 |
Wichtigste Unterscheidungsmerkmale
- Combines a 14-stage divider with a 24 MHz maximum clock frequency (vs. CD4020BE)
- Provides a 3 V to 18 V operating range for multi-voltage CMOS systems (vs. CD4020BF3A)
- Uses a 16-CFP through-hole package suited to legacy and serviceable assemblies (vs. CD4020BE)
Designhinweise
Route the clock as a short trace and provide a clean negative transition at the counter input. Slow clock edges increase the probability of metastability and incorrect counting. Keep switching-node wiring, high-current relay returns, and oscillator outputs physically separated when practical; add a local ground reference for any buffer or signal-conditioning stage driving the CD4020BK3.
Use the manufacturer pin-description table and package drawing to assign the 16-CFP footprint. Confirm lead pitch, row spacing, and pin-1 orientation rather than treating every DIP-16 counter as electrically identical. Place the reset trace away from high-current switching paths, and provide adequate clearance from adjacent components so the counter can be socketed where legacy serviceability is important.
Do not treat all Q outputs as changing simultaneously in a ripple counter. Propagation delay accumulates from one stage to the next, so downstream logic should use the stage whose timing is specified. Also avoid relying on an unconnected stage to remain permanently low; unused outputs should be left unconnected unless a defined reset or power-up state is required by the system.
Operate the CD4020BK3 only within its 3 V to 18 V supply range and use a local bypass capacitor near the package supply connection. The bypass path should be short and returned to the device ground without sharing a long current path with unrelated switching stages. Confirm the supply sequence and input limits if the same board can start with the counter supply absent while an external clock source remains powered.
Compliance-Informationen
No definitive environmental or material-compliance declarations were identified for the exact CD4020BK3 ordering code. The family is a CMOS logic IC and is not presented as an automotive-qualified device.