DG441CJ+ - Quad SPST Analog Switch | Analog Devices
Teilenummer: DG441CJ+ ✓ AktivDG441CJ+ Übersicht
A CMOS analog switch is a semiconductor device that routes electrical signals between terminals under digital control. It belongs to the analog switch and multiplexer hierarchy, which falls under interface ICs and ultimately semiconductor signal-management components. The DG441CJ+ uses four independent single-pole, single-throw channels. Each channel connects its common terminal to one switched terminal while remaining normally closed when no control voltage is applied.
The principal advantages of the DG441CJ+ include low charge injection of 10 pC maximum, low power consumption of 1.65 mW, and ESD tolerance of 2000 V minimum. These characteristics make the device useful when a design must switch analog signals while limiting control-signal transients and maintaining consistent resistance among channels. The 85 ohm maximum on-resistance specification is important for source impedance, signal attenuation, and bandwidth calculations.
The DG441 design provides symmetric low on-resistance behavior in either signal direction. Its matching specification of 4 ohms maximum reduces channel-to-channel variation, while the 9 ohms maximum flatness specification limits resistance changes over the operating signal range. These characteristics are particularly useful in instrumentation, data acquisition, test systems, and control interfaces where four channels must present similar electrical behavior.
Typical uses include routing sensor outputs into an analog-to-digital converter, selecting test points in automated test equipment, switching bipolar or unipolar analog signals, and building sample-and-hold or measurement front ends. The four normally closed channels are particularly suitable when the system must maintain a defined signal connection during reset, power-up, or control transitions.
PCB design should account for the relatively high 85 ohm maximum on-resistance rather than treating the switch as a low-resistance power mux. Keep analog traces short, provide a stable ground reference, and route control inputs away from sensitive analog paths. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before finalizing the layout.
This page combines the manufacturer product information, exact DG441CJ+ ordering information, electrical characteristics, application guidance, and drop-in replacement analysis to support faster component selection and PCB implementation.
Drop-in-Alternativen für DG441CJ+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DG441CJ+ (gleiche Bauform und Footprint) – abweichend in Mounting Type, Package, Switch Configuration.
DG441LE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DG441CJ+ Grenzwerte & elektrische Eigenschaften
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| Number of Switches | 4 |
| Switch State | Normally closed |
| On-Resistance | 85 ohms maximum |
| On-Resistance Matching | 4 ohms maximum |
| On-Resistance Flatness | 9 ohms maximum |
| Charge Injection | 10 pC maximum |
| Power Consumption | 1.65 mW |
| ESD Tolerance | 2000 V minimum |
| Conduction Direction | Bidirectional |
| Technology | CMOS |
| Gehäuse | 16-pin DIP |
| Terminal Count | 16 terminals |
| Montageart | Through-hole |
| Lead-Free Suffix | + at the end of the part number |
| Production Status | Production |
DG441CJ+ 16-pin dip Pinbelegungsleitfaden
Pinbelegung für DG441CJ+ (16-pin dip-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für DG441CJ+.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DG441CJ+ ist geeignet für 6 Anwendungs: Multiplexed Sensor Acquisition, Automated Test Equipment, Data Acquisition Front Ends, Analog Signal Routing, Sample-and-Hold Systems, Process Control Interfaces.
Multiplexed Sensor Acquisition
The DG441CJ+ is appropriate for routing multiple analog sensor outputs into a shared measurement channel. Its four independent normally closed SPST paths provide continuity when control signals are inactive, while the 4 ohm maximum on-resistance matching helps maintain similar source impedance across channels. The 85 ohm maximum on-resistance must be included in the input-network design. For a divider network and amplifier, account for the switched resistance when calculating gain and loading. Its 10 pC maximum charge injection also helps limit control-induced transients into high-impedance sensor interfaces.
Empfohlen
Automated Test Equipment
The DG441CJ+ can select test paths in automated test equipment because it provides four independent SPST routes with controlled default continuity. The specified on-resistance matching of 4 ohms maximum and flatness of 9 ohms maximum support repeatable channel behavior when several test points are alternated. Designers should still calculate the attenuation introduced by the 85 ohm maximum on-resistance. Low power consumption of 1.65 mW also helps when the switch remains active across a larger test fixture.
Empfohlen
Data Acquisition Front Ends
The DG441CJ+ is useful in data-acquisition front ends where several inputs must be selected before an ADC. Four normally closed channels preserve their default connections during control reset, reducing unintended disconnects in systems that interpret an inactive path as the valid measurement. The 10 pC maximum charge-injection value is particularly relevant when driving high-impedance sources. Account for the 85 ohm maximum on-resistance when setting the acquisition bandwidth, and use short analog routing to minimize additional parasitic capacitance.
Empfohlen
Analog Signal Routing
The DG441CJ+ provides a straightforward way to route a controlled analog signal through a 16-pin DIP analog switch. Bidirectional conduction allows the common and switched terminals to be assigned according to the system signal direction. The on-resistance matching of 4 ohms maximum helps reduce channel-dependent errors, while flatness of 9 ohms maximum limits variation over the signal range. The 85 ohm maximum on-resistance makes it more appropriate for instrumentation and precision control than for low-impedance power switching.
Empfohlen
Sample-and-Hold Systems
The DG441CJ+ can serve as part of a sample-and-hold or track-and-hold signal path by connecting a selected source to a holding network. Its normally closed channels allow a defined default connection during reset, which can simplify fault-state interpretation in control systems. Low charge injection of 10 pC maximum reduces unwanted voltage steps when control changes occur. The design must nevertheless account for the 85 ohm maximum on-resistance, leakage behavior, and the settling requirements of the selected sampling capacitor.
Empfohlen
Process Control Interfaces
The DG441CJ+ is suitable for low-power process-control interfaces that switch command or sensor signals between measurement and test paths. Four normally closed channels can preserve established connections when a controller resets or its output enters an inactive state. Its 1.65 mW power consumption helps limit dissipation in multi-channel control assemblies, while 2000 V minimum ESD tolerance provides a defined protection level for sensitive equipment. Confirm the complete supply, control, and signal ratings before using the device near external wiring.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DG441CJ+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Designhinweise
Use the manufacturer pin-configuration table to assign every DG441CJ+ terminal before routing the PCB. Treat the 85 ohm maximum on-resistance as part of the signal path rather than as an ideal switch. Calculate the resulting divider with the driven source impedance, and confirm that the acquisition amplifier remains stable with the selected load and board capacitance.
Place the DG441CJ+ close to the signal source or destination so that the switched path does not add unnecessary trace resistance or capacitance. Keep the analog traces short and provide a low-impedance ground reference. Route digital control traces away from sensitive analog nets and use a quiet ground strategy appropriate to the surrounding analog system.
Do not substitute a normally open DG442-family device for the normally closed DG441CJ+; the default signal state would reverse. Also verify the + suffix because it identifies lead-free ordering. Review the datasheet for supply limits, control thresholds, leakage, and absolute maximum ratings before finalizing a design.
Compliance-Informationen
The manufacturer ordering information states that the terminal + symbol designates lead-free packaging. No explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement was identified for the exact ordering code.