Analog Devices

DG441CJ+ - Quad SPST Analog Switch | Analog Devices

部品番号: DG441CJ+ ✓ 生産中
85 ohms maximum Rds(on) 16-pin DIP Package
MOQ: 1 |

DG441CJ+ 概要

Analog Devices DG441CJ+ is a production, quad SPST CMOS analog switch with four normally closed circuits, an 85 ohm on-resistance rating, and a 16-pin DIP package. The DG441 family provides on-resistance matching of 4 ohms maximum between switches and on-resistance flatness of 9 ohms maximum across the signal range. A lead-free marking is identified by the terminal + suffix.

A CMOS analog switch is a semiconductor device that routes electrical signals between terminals under digital control. It belongs to the analog switch and multiplexer hierarchy, which falls under interface ICs and ultimately semiconductor signal-management components. The DG441CJ+ uses four independent single-pole, single-throw channels. Each channel connects its common terminal to one switched terminal while remaining normally closed when no control voltage is applied.

The principal advantages of the DG441CJ+ include low charge injection of 10 pC maximum, low power consumption of 1.65 mW, and ESD tolerance of 2000 V minimum. These characteristics make the device useful when a design must switch analog signals while limiting control-signal transients and maintaining consistent resistance among channels. The 85 ohm maximum on-resistance specification is important for source impedance, signal attenuation, and bandwidth calculations.

The DG441 design provides symmetric low on-resistance behavior in either signal direction. Its matching specification of 4 ohms maximum reduces channel-to-channel variation, while the 9 ohms maximum flatness specification limits resistance changes over the operating signal range. These characteristics are particularly useful in instrumentation, data acquisition, test systems, and control interfaces where four channels must present similar electrical behavior.

Typical uses include routing sensor outputs into an analog-to-digital converter, selecting test points in automated test equipment, switching bipolar or unipolar analog signals, and building sample-and-hold or measurement front ends. The four normally closed channels are particularly suitable when the system must maintain a defined signal connection during reset, power-up, or control transitions.

PCB design should account for the relatively high 85 ohm maximum on-resistance rather than treating the switch as a low-resistance power mux. Keep analog traces short, provide a stable ground reference, and route control inputs away from sensitive analog paths. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before finalizing the layout.

This page combines the manufacturer product information, exact DG441CJ+ ordering information, electrical characteristics, application guidance, and drop-in replacement analysis to support faster component selection and PCB implementation.

ドロップイン代替品: DG441CJ+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: DG441CJ+ (同一形状・フットプリント) — 相違点: Mounting Type, Package, Switch Configuration.

Renesas Electronics
Mounting Type: Through Hole
Package: 16-PDIP
Switch Configuration: Quad SPST, Normally Closed
比較対象 DG441CJ+ →

DG441LE

✅ ドロップイン
📦 16-pin DIP
The cross-reference identifies the same 16-pin quad SPST form factor, but exact on-resistance and control differences require verification; the DG441CJ+ is rated at 85 Ω maximum on-resistance.

📋 参考代替品(カタログ未掲載)

DG441CJ+ 最大定格&電気的特性

Number of Circuits 4 circuits
Switch Configuration 1:1 SPST
Number of Switches 4
Switch State Normally closed
On-Resistance 85 ohms maximum
On-Resistance Matching 4 ohms maximum
On-Resistance Flatness 9 ohms maximum
Charge Injection 10 pC maximum
Power Consumption 1.65 mW
ESD Tolerance 2000 V minimum
Conduction Direction Bidirectional
Technology CMOS
パッケージ 16-pin DIP
Terminal Count 16 terminals
実装タイプ Through-hole
Lead-Free Suffix + at the end of the part number
Production Status Production

DG441CJ+ 16-pin dip ピン配置ガイド

DG441CJ+ (16-pin dip パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

DG441CJ+ の 16-pin dip パッケージピン配置図

詳細なピン配置データはありません: DG441CJ+.

詳細は データシート をご参照ください。

主な用途

DG441CJ+ の用途: 6 件s: Multiplexed Sensor Acquisition, Automated Test Equipment, Data Acquisition Front Ends, Analog Signal Routing, Sample-and-Hold Systems, Process Control Interfaces.

🧩

Multiplexed Sensor Acquisition

The DG441CJ+ is appropriate for routing multiple analog sensor outputs into a shared measurement channel. Its four independent normally closed SPST paths provide continuity when control signals are inactive, while the 4 ohm maximum on-resistance matching helps maintain similar source impedance across channels. The 85 ohm maximum on-resistance must be included in the input-network design. For a divider network and amplifier, account for the switched resistance when calculating gain and loading. Its 10 pC maximum charge injection also helps limit control-induced transients into high-impedance sensor interfaces.

🔧

Automated Test Equipment

The DG441CJ+ can select test paths in automated test equipment because it provides four independent SPST routes with controlled default continuity. The specified on-resistance matching of 4 ohms maximum and flatness of 9 ohms maximum support repeatable channel behavior when several test points are alternated. Designers should still calculate the attenuation introduced by the 85 ohm maximum on-resistance. Low power consumption of 1.65 mW also helps when the switch remains active across a larger test fixture.

📊

Data Acquisition Front Ends

The DG441CJ+ is useful in data-acquisition front ends where several inputs must be selected before an ADC. Four normally closed channels preserve their default connections during control reset, reducing unintended disconnects in systems that interpret an inactive path as the valid measurement. The 10 pC maximum charge-injection value is particularly relevant when driving high-impedance sources. Account for the 85 ohm maximum on-resistance when setting the acquisition bandwidth, and use short analog routing to minimize additional parasitic capacitance.

🌐

Analog Signal Routing

The DG441CJ+ provides a straightforward way to route a controlled analog signal through a 16-pin DIP analog switch. Bidirectional conduction allows the common and switched terminals to be assigned according to the system signal direction. The on-resistance matching of 4 ohms maximum helps reduce channel-dependent errors, while flatness of 9 ohms maximum limits variation over the signal range. The 85 ohm maximum on-resistance makes it more appropriate for instrumentation and precision control than for low-impedance power switching.

📡

Sample-and-Hold Systems

The DG441CJ+ can serve as part of a sample-and-hold or track-and-hold signal path by connecting a selected source to a holding network. Its normally closed channels allow a defined default connection during reset, which can simplify fault-state interpretation in control systems. Low charge injection of 10 pC maximum reduces unwanted voltage steps when control changes occur. The design must nevertheless account for the 85 ohm maximum on-resistance, leakage behavior, and the settling requirements of the selected sampling capacitor.

🏭

Process Control Interfaces

The DG441CJ+ is suitable for low-power process-control interfaces that switch command or sensor signals between measurement and test paths. Four normally closed channels can preserve established connections when a controller resets or its output enters an inactive state. Its 1.65 mW power consumption helps limit dissipation in multi-channel control assemblies, while 2000 V minimum ESD tolerance provides a defined protection level for sensitive equipment. Confirm the complete supply, control, and signal ratings before using the device near external wiring.

おすすめ製品の概要

AD8627 Low-offset amplifier for sensor interface signals 使用用途: Multiplexed Sensor Acquisition, Data Acquisition Front Ends, Analog Signal Routing, Sample-and-Hold Systems AD7768 Precision ADC for multiplexed analog channels 使用用途: Multiplexed Sensor Acquisition, Data Acquisition Front Ends, Sample-and-Hold Systems AD9164 Signal generator output interface 使用用途: Automated Test Equipment, Analog Signal Routing, Process Control Interfaces AD9680 Analog Devices 使用用途: Automated Test Equipment, Process Control Interfaces
What is the DG441CJ+?
The DG441CJ+ is a quad SPST CMOS analog switch with four normally closed channels, an 85 ohm maximum on-resistance, and a 16-pin DIP package. According to the Analog Devices DG441 product page and manufacturer datasheet, it is a production device designed for low-power analog signal routing. The + suffix identifies lead-free ordering.
How many switches does DG441CJ+ have?
The DG441CJ+ contains four independent SPST switches. According to the Analog Devices DG441 product page, it is a quad, SPST analog switch with a 1:1 signal configuration. Each switched path is normally closed, allowing the device to maintain a connection when its control input is inactive.
What is the on-resistance of DG441CJ+?
The DG441CJ+ has a maximum on-resistance of 85 ohms. The manufacturer datasheet also specifies on-resistance matching of 4 ohms maximum between switches and on-resistance flatness of 9 ohms maximum over the signal range. These values should be included when calculating insertion loss, source impedance, and signal-bandwidth performance.
Where can I download the DG441CJ+ datasheet PDF?
The official DG441 documentation is available through the Analog Devices DG441 product page, which links the manufacturer data sheet. A manufacturer-document copy is also accessible through the DG441CJ datasheet PDF result. Use the pin-description table, electrical-characteristics table, and ordering-information section when finalizing a PCB design.
Where can I find the DG441CJ+ pinout?
The DG441CJ+ pinout is defined in the pin-configuration section of the Analog Devices DG441 manufacturer datasheet. The device uses a 16-pin DIP package, and every connection should be assigned from that document rather than inferred from a generic switch diagram. Confirm pin numbering, common terminals, switched terminals, control inputs, and supply connections before layout release.
What is the DG441CJ+ equivalent?
The closest functional equivalent is a lead-free DG441 family device with the same quad, normally closed SPST configuration, 16-pin DIP footprint, and comparable electrical ratings. Before substitution, verify the exact ordering suffix, control polarity, supply limits, and pin configuration in the manufacturer datasheet. A DG442-family device is not interchangeable because its channels are normally open.
Is the DG441CJ+ the same as DG442CJ+?
No. The DG441CJ+ has four normally closed SPST channels, while the DG442 family uses normally open channels. Although both devices are related quad SPST CMOS analog switches, their default signal paths are opposite. Using DG442CJ+ in a DG441CJ+ socket would change the circuit behavior when the control input is inactive and therefore is not a valid drop-in replacement.
When should I choose DG441CJ+ instead of a normally open switch?
Choose the DG441CJ+ when the signal path must remain connected during reset, power-up, or an inactive control state. Its four normally closed channels preserve continuity without requiring an external pull-up or relay. Select a normally open device instead when channels must remain disconnected during control reset or when fail-safe isolation is more important than continuity.
Can DG441CJ+ replace DG444DJ+?
No. The DG444DJ+ is a quad SPST switch with normally open channels, while the DG441CJ+ has normally closed channels. The devices also use different package configurations. This makes DG444DJ+ unsuitable as a direct drop-in replacement unless the PCB is redesigned and the required default switch state is intentionally changed.
What is the best Maxim Integrated equivalent for DG441CJ+?
The best equivalent is another lead-free DG441-family device that preserves the quad, normally closed SPST architecture and the 16-pin DIP pinout. The exact suffix must be checked for package, temperature grade, and lead-free construction. The manufacturer datasheet is the controlling document for confirming electrical equivalence and lifecycle status.
Where can I buy DG441CJ+ and check its price?
Use the Request a Quote form on this page to request DG441CJ+ pricing, availability, lead time, and minimum order quantity from XAIPART. The component is identified as an Analog Devices production device, but current commercial terms can change. Submit the required quantity and packaging details with the quote request for a current response.
What is the price of DG441CJ+?
Use the Request a Quote form on this page for a current DG441CJ+ price. XAIPART confirms commercial pricing against the requested quantity and order conditions rather than publishing a static figure that may become stale. Include the required order quantity, delivery destination, and preferred packaging when submitting the request.
What is the lead time for DG441CJ+?
Use the Request a Quote form on this page to request the current DG441CJ+ lead time and stock status. The Analog Devices product page identifies the DG441 family as being in production, but production status does not by itself establish available inventory or a delivery date. XAIPART can confirm scheduling for the requested quantity through the quote process.
Is DG441CJ+ in stock?
The current DG441CJ+ stock position should be requested through the Request a Quote form on this page. The manufacturer lists the DG441 family as a production device, but production lifecycle status is not a guarantee of immediate inventory, allocation, or a fixed delivery schedule. Provide the required quantity so XAIPART can respond with current availability.
What are the key specifications of DG441CJ+ that engineers should know?
The DG441CJ+ combines four normally closed SPST channels in a 16-pin DIP package with an 85 ohm maximum on-resistance. According to the Analog Devices manufacturer datasheet, additional key values include 4 ohms maximum on-resistance matching, 9 ohms maximum flatness, 10 pC maximum charge injection, 1.65 mW power consumption, and 2000 V minimum ESD tolerance.
Is DG441CJ+ suitable for instrumentation and test equipment?
The DG441CJ+ is suitable for instrumentation and automated test systems that require four independent analog paths with a normally closed default state. Its 4 ohm maximum channel matching and 9 ohm maximum flatness help limit variation between switched routes. The 85 ohm maximum on-resistance must still be included in the front-end signal-budget calculation.

エンジニアリング参考データ: DG441CJ+ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the DG441CJ+ when the circuit requires four independent analog paths that remain connected during reset or an inactive control state. Its specified 4 ohm maximum on-resistance matching and 9 ohm maximum flatness help maintain consistent channel behavior, while the 10 pC maximum charge injection and 1.65 mW power consumption suit precision, low-power instrumentation. The 85 ohm maximum on-resistance is the principal limitation: it is appropriate for sensor, test, and control-signal routing but not for low-impedance power paths. A normally open switch should be selected when disconnection during reset is required instead of continuity. No alternate part is presented as a drop-in replacement because the retrieved cross-reference results did not identify a candidate whose package, pinout, default state, and electrical limits were all confirmed.

設計ノート

Use the manufacturer pin-configuration table to assign every DG441CJ+ terminal before routing the PCB. Treat the 85 ohm maximum on-resistance as part of the signal path rather than as an ideal switch. Calculate the resulting divider with the driven source impedance, and confirm that the acquisition amplifier remains stable with the selected load and board capacitance.

Place the DG441CJ+ close to the signal source or destination so that the switched path does not add unnecessary trace resistance or capacitance. Keep the analog traces short and provide a low-impedance ground reference. Route digital control traces away from sensitive analog nets and use a quiet ground strategy appropriate to the surrounding analog system.

Do not substitute a normally open DG442-family device for the normally closed DG441CJ+; the default signal state would reverse. Also verify the + suffix because it identifies lead-free ordering. Review the datasheet for supply limits, control thresholds, leakage, and absolute maximum ratings before finalizing a design.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Yes
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The manufacturer ordering information states that the terminal + symbol designates lead-free packaging. No explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement was identified for the exact ordering code.

データ検証日: 2026-11-10 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

DG441CJ+ datasheet DG441CJ+ pinout DG441CJ+ datasheet pdf DG441CJ+ equivalent DG441CJ+ replacement DG441CJ+ cross reference Analog Devices DG441CJ+ DG441CJ+ 85 ohm switch DG441CJ+ 16 pin DIP DG441CJ+ price DG441CJ+ stock DG441CJ+ sensor multiplexing

関連部品&用語

Analog Devices Maxim Integrated DG441CJ+ DG441 DG442 DG444DJ+ quad SPST analog switch normally closed switch CMOS analog switch analog multiplexer interface IC semiconductor on-resistance on-resistance matching on-resistance flatness charge injection bidirectional switch 16-pin DIP through-hole package lead-free packaging ESD tolerance sensor multiplexing automated test equipment data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示