DG441CY+T - 4-Channel SPST Analog Switch | Analog Devices
Teilenummer: DG441CY+T ✓ AktivDG441CY+T Übersicht
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG441 belongs to the analog switch category within the broader signal-path and power-management ecosystem. Its four independent SPST channels can connect or disconnect analog, audio, instrumentation, communication, and battery-powered system signals while minimizing insertion loss and distortion.
Key features include 85 ohm maximum on-resistance, on-resistance matching of 4 ohm maximum between switches, and guaranteed on-resistance flatness of 9 ohm maximum over the signal range. The switching characteristics include turn-on time below 250 ns and turn-off time below 170 ns. These parameters make the device useful where controlled analog routing must coexist with digital control logic.
The DG441 family uses a 44 V silicon-gate CMOS process. Its logic-compatible control inputs and symmetric on-state conduction support signal routing in either direction. The low matching and flatness specifications help preserve amplitude consistency when multiple channels must behave similarly, which is important in measurement, communication, and audio systems.
Typical applications include audio-signal routing, battery-powered equipment, communication systems, fax equipment, instrumentation, and test systems. The device can be used to select between sensor sources, route test signals, disconnect loads, or preserve a common analog path while keeping control logic separated from the analog signal.
Designers should verify the positive and negative supply limits, control-logic levels, signal-range restrictions, and maximum switch current in the manufacturer datasheet. Place bypass capacitors close to the supply pins and route control traces away from sensitive analog inputs to reduce coupling and switching transients.
This product page combines package, performance, application, and selection guidance with a focused comparison against pin-compatible DG441-family devices. It is intended to help engineers identify the correct supply configuration, package variant, and replacement option before integrating the switch into a PCB design.
Drop-in-Alternativen für DG441CY+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DG441CY+T (gleiche Bauform und Footprint) – abweichend in Package, Switch Configuration, Bipolar Supply Range, Logic Input Compatibility, Number of Switches.
DG441CY+
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →DG441DY-T1-E3
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DG441DY+T
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →DG441DYZ
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →DG441DYZ
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →DG441CY+T Grenzwerte & elektrische Eigenschaften
| Number of Channels | 4 channels |
| Switch Configuration | 4 x SPST, normally closed |
| On-Resistance | 85 ohm maximum |
| On-Resistance Matching | 4 ohm maximum between switches |
| On-Resistance Flatness | 9 ohm maximum over the signal range |
| Turn-On Time | Less than 250 ns |
| Turn-Off Time | Less than 170 ns |
| Positive Single-Supply Range | +10 V to +30 V |
| Bipolar Supply Range | +/-4.5 V to +/-20 V |
| Process Technology | 44 V silicon-gate CMOS |
| Gehäuse | 16-lead SOIC |
| Montageart | Surface mount |
| Control Logic Compatibility | TTL and CMOS compatible |
| Signal Conduction | Symmetric, in either direction |
DG441CY+T 16-lead soic Pinbelegungsleitfaden
Pinbelegung für DG441CY+T (16-lead soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für DG441CY+T.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DG441CY+T ist geeignet für 6 Anwendungs: Audio Signal Routing, Communication Signal Routing, Battery-Powered Instrumentation, Test and Measurement Systems, Battery-Powered Signal Isolation, Analog Multiplexing.
Audio Signal Routing
The DG441CY+T suits audio-signal routing because each of its four SPST channels has an 85 ohm maximum on-resistance, while channel matching is specified at 4 ohm maximum and flatness at 9 ohm maximum. This helps maintain consistent signal amplitude when routing audio between amplifier, source, and test paths. The symmetric CMOS switch conducts in either direction, so the same device can support source selection or load isolation. According to the Analog Devices DG441 documentation, audio routing is an intended application. Designers should still verify bandwidth, distortion, signal amplitude, and switch-current limits for the specific audio circuit.
Empfohlen
Communication Signal Routing
The DG441CY+T can route communication signals through four independently controlled, normally closed SPST channels. Its 85 ohm maximum on-resistance is suitable for many moderate-impedance routing paths, while less than 250 ns turn-on and less than 170 ns turn-off timing support controlled signal selection. The Analog Devices DG441 family explicitly identifies communication systems as an application. For higher-frequency or low-impedance nodes, engineers should confirm the complete frequency-response, capacitance, insertion-loss, and signal-range specifications before assigning the switch to a critical path.
Empfohlen
Battery-Powered Instrumentation
The DG441CY+T is suitable for battery-powered instrumentation where four analog paths must be selected while preserving signal integrity and maintaining controlled off-state isolation. The family supports +10 V to +30 V single-supply or ±4.5 V to ±20 V bipolar operation, allowing integration into both single-ended and split-supply analog systems. Its 44 V silicon-gate process and improved channel matching can support repeatable measurements across multiple inputs. Because battery systems are sensitive to leakage and supply demand, the exact off-leakage, power-consumption, and allowable voltage limits must be checked in the manufacturer specifications.
Empfohlen
Test and Measurement Systems
The DG441CY+T provides four normally closed switch sections for connecting test signals, selecting instrument paths, and isolating unused inputs. A maximum on-resistance of 85 ohm, matching of 4 ohm maximum between switches, and flatness of 9 ohm maximum help reduce channel-to-channel measurement variation. Its fast turn-on and turn-off timing also make it practical for automated routing sequences. The manufacturer lists test systems among the DG441 applications. For precision measurement, validate leakage, input impedance, contact resistance in the complete path, and ground offsets against the accuracy required by the instrument.
Empfohlen
Battery-Powered Signal Isolation
The DG441CY+T can isolate inactive loads or disconnect alternate signal sources in battery-powered products because each SPST channel can be placed in a normally closed or open state through its control input. Four channels provide compact multiplexing without requiring four separate packages, and the 85 ohm maximum on-resistance can provide an acceptable insertion loss in suitable moderate-impedance circuits. The family explicitly supports battery-powered applications. Check the off-state leakage carefully because it can dominate standby power, and confirm that the control polarity and inactive-state behavior match the surrounding system logic.
Empfohlen
Analog Multiplexing
The four SPST channels in the DG441CY+T can be combined with external circuitry to create compact analog multiplexing and source-selection arrangements. The normally closed topology provides a defined default connection, while the 85 ohm maximum on-resistance and 9 ohm maximum flatness help preserve signal consistency as different paths are selected. The manufacturer identifies communication and signal-routing uses for the DG441 family. When multiplexing precision sensors, verify the switch's leakage, charge injection, off-state isolation, and behavior over the full input range so the practical resolution remains suitable for the measurement system.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DG441CY+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DG441CY | DG441DY-T1-E3 | DG441DY+T | DG441DY | DG441DYZ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 x SPST, normally closed | SPST, normally closed | SPST, normally closed | SPST, normally closed | SPST, normally closed | SPST, normally closed |
| On-Resistance | 85 ohm maximum | 85 ohm | 85 ohm | 85 ohm | 85 ohm | 85 ohm |
Wichtigste Unterscheidungsmerkmale
- Identified pin-compatible second-source architecture (vs. DG441DY-T1-E3)
- Documented channel-to-channel resistance matching (vs. DG441DY+T)
- Fast control response for analog selection (vs. DG441DYZ)
- Manufacturer-direct DG441 documentation (vs. DG441DY-T1-E3)
Designhinweise
Route each control input away from the four analog signal paths and connect the device ground pins with a low-impedance return. Place supply bypass capacitors close to the supply pins, and keep the analog traces short where the switched source has high impedance. Because the DG441 provides four independently controlled channels, consistent grounding and short control traces help prevent switching transients from appearing as signal errors in adjacent channels.
Choose the supply arrangement from the Analog Devices operating conditions: +10 V to +30 V for single-supply operation or ±4.5 V to ±20 V for bipolar operation. Ensure that every signal remains within the permitted input range and that the control levels are valid for the selected rails. Do not assume that a logic-compatible control input permits operation outside the specified supply range; check absolute maximum and recommended operating conditions before power sequencing the board.
Do not treat the 85 ohm maximum on-resistance as a constant value across every signal condition. The DG441 family specifies 4 ohm maximum matching between switches and 9 ohm maximum flatness over the signal range, so the resistance can vary with signal amplitude and device conditions. Use the complete electrical-characteristics curves when designing divider networks, high-impedance sensors, precision gain stages, or paths where channel-to-channel resistance variation would affect the final measurement.
Check the physical pinout for the exact ordering code before placing a cross-manufacturer alternative. The DG441DY-T1-E3, DG441DY+T, DG441DY, and DG441DYZ candidates share the 16-SOIC package family, but package equivalence alone does not prove that control polarity, logic thresholds, supply limits, leakage, and absolute maximum conditions are identical. Perform a complete manufacturer-datasheet comparison before treating any listed alternative as a production drop-in replacement.
Compliance-Informationen
Compliance status for the exact DG441CY+T ordering code was not established by the available manufacturer and distributor information. Automotive qualification is not claimed.