Texas Instruments

DS90CR286ASLC - 28-Bit LVDS Channel-Link Receiver | Texas Instruments

Teilenummer: DS90CR286ASLC ✓ Aktiv
3 V to 3.6 V Vdss 64-pin NFBGA, 8 x 8 mm Package 66 MHz Speed
MOQ: 1 |

DS90CR286ASLC Übersicht

The Texas Instruments DS90CR286ASLC is a 3.3 V rising-edge data-strobe LVDS receiver that converts four differential LVDS data streams into 28 parallel CMOS/TTL data bits. It is designed for 28-bit Channel Link communication at up to 66 MHz and uses a 64-pin NFBGA package, identified in distributor information as an 8 x 8 mm package. The receiver is intended for high-speed point-to-point links where four LVDS data channels and a separate clock channel carry data from a transmitter to a receiving device.

A Channel Link receiver is an interface IC that reconstructs parallel digital data from differential low-voltage differential signaling pairs. LVDS, or low-voltage differential signaling, is a high-speed electrical interface designed to reduce common-mode noise and support reliable data transfer over balanced conductors. The DS90CR286ASLC is therefore positioned within the interface-IC hierarchy, alongside parallel-to-serial and serial-to-parallel data converters, rather than with general-purpose logic or memory devices.

The main functional characteristics visible in the manufacturer and distributor information are the 4-to-28 LVDS-to-parallel conversion, 3 V to 3.6 V supply range, 66 MHz channel-link operating frequency, and up to 1.848 Gbps throughput or 231 MB/s bandwidth. The rising-edge data-strobe architecture allows the receiver to transfer 28 data bits in parallel while the companion DS90CR285 transmitter serializes the corresponding data stream. The use of LVDS can help reduce signal-integrity problems associated with single-ended high-speed interconnects.

The DS90CR286ASLC is used in industrial data acquisition, test and measurement equipment, instrumentation, communications equipment, and other systems requiring a high-speed parallel data interface. The receiver can be paired with a compatible transmitter and an FPGA or other parallel-processing device. Designers must account for the specified 3.3 V supply, correct LVDS input termination and topology, clock/data-strobe alignment, decoupling, and the package's thermal and layout requirements.

For PCB implementation, place the receiver close to the LVDS connector or transmitter, follow the manufacturer's recommended decoupling and controlled-impedance routing, and keep unused inputs in the states specified by the datasheet. The package pinout and detailed electrical limits should be taken from the current Texas Instruments DS90CR286 datasheet before final schematic and layout release. This page organizes the available technical information, sourcing guidance, comparison points, and design considerations around the DS90CR286ASLC.

Drop-in-Alternativen für DS90CR286ASLC – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

DS90CR286A

✅ Drop-In
📦 64-pin NFBGA (8 x 8 mm)
Revised A-family timing or device revision versus the original DS90CR286 family; electrical differences require datasheet confirmation.

📋 Referenzalternative (nicht im Katalog)

DS90CR285

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 64-pin NFBGA (8 x 8 mm)
Companion transmitter rather than receiver; it provides the transmit side of the Channel Link and is not an electrical replacement for the DS90CR286ASLC receiver.

📋 Referenzalternative (nicht im Katalog)

DS90CR285A

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 64-pin NFBGA (8 x 8 mm)
Companion A-family transmitter with a revised device designation; it is not a functional substitute for the receiver.

📋 Referenzalternative (nicht im Katalog)

DS90CR286

✅ Drop-In
📦 64-pin NFBGA (8 x 8 mm)
Base-family device designation for the same 4-to-28 66 MHz LVDS receiver function; suffix and orderable details must be checked.

📋 Referenzalternative (nicht im Katalog)

DS90CR216A

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 64-pin NFBGA (8 x 8 mm)
Different 3-to-21 LVDS Channel Link receiver channel count; lower data width than the DS90CR286ASLC despite the similar family package.

📋 Referenzalternative (nicht im Katalog)

DS90CR286ASLC Technische Daten

Product Type LVDS to parallel CMOS/TTL receiver
Funktion 4 differential LVDS data streams to 28 parallel data bits
Supply Voltage Range 3 V to 3.6 V
Nominal Supply Voltage 3.3 V
Channel-Link Operating Frequency 66 MHz
Data Throughput Up to 1.848 Gbps
Bandwidth 231 MB/s
Number of Drivers 4
Number of Receivers 28
Receiver Type LVDS receiver
Data Interface CMOS/TTL parallel output
Signal Type LVDS
Edge Type Rising edge data strobe
Gehäuse 64-pin NFBGA, 8 x 8 mm
Packaging Tube
Lead-Free Status Contains lead per distributor listing

DS90CR286ASLC 64-pin nfbga, 8 x 8 mm Pinbelegungsleitfaden

Pinbelegung für DS90CR286ASLC (64-pin nfbga, 8 x 8 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für DS90CR286ASLC im 64-pin nfbga, 8 x 8 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für DS90CR286ASLC.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

DS90CR286ASLC ist geeignet für 6 Anwendungs: Industrial Data Acquisition, FPGA Parallel Data Interface, Test and Measurement Equipment, Communications and Networking Equipment, Instrumentation and Control Systems, High-Speed Digital Backplane Interface.

🏭

Industrial Data Acquisition

The DS90CR286ASLC is suitable for industrial data-acquisition systems that receive 28-bit parallel data over a high-speed LVDS link. Its four differential LVDS inputs provide a noise-resistant transfer path between a remote transmitter and a controller, while the 66 MHz Channel Link rate supports data movement at up to 1.848 Gbps. The receiver can feed a parallel FPGA interface when voltage, clocking, and timing requirements match. Designers should use the manufacturer application guidance for input termination, controlled-impedance routing, BGA layout, and power decoupling.

🖥️

FPGA Parallel Data Interface

The DS90CR286ASLC can serve as the LVDS-to-parallel interface between a high-speed link and an FPGA. Its 28 CMOS/TTL outputs provide a wide parallel bus, while the rising-edge data-strobe relationship supports deterministic sampling by the receiving logic. At 66 MHz, the documented throughput reaches 1.848 Gbps before protocol overhead. The FPGA design must match the receiver's 3.3 V interface, establish the correct data-strobe phase, and provide timing margin for cable skew, jitter, and board propagation delay.

📡

Test and Measurement Equipment

The DS90CR286ASLC is appropriate for test and measurement instrumentation that transports a 28-bit measurement or control word over a high-speed differential link. LVDS reduces susceptibility to common-mode interference compared with a single-ended implementation, which is useful in equipment containing switching supplies, clocks, and analog sections. The receiver's 66 MHz operation and 231 MB/s bandwidth allow rapid parallel data transfer. Grounding, return paths, connector transitions, shielding, and power-supply separation should be designed to preserve signal integrity across the complete instrument enclosure.

🌐

Communications and Networking Equipment

The DS90CR286ASLC can be used in communications equipment that needs a reliable parallel data path between line-card or backplane electronics and a processing section. Four LVDS channels and 28 recovered data bits provide a compact interface for high-speed serialized transfers without exposing the full parallel bus to board-level noise. The 3.3 V operating range and NFBGA footprint support compact designs, but the system must verify connector and cable loss, clock recovery, grounding, and any regulatory EMC requirements before production use.

🔧

Instrumentation and Control Systems

The DS90CR286ASLC is useful in instrumentation and control systems that exchange wide parallel words with external sensors, programmable instruments, or remote I/O. A differential LVDS link can improve noise immunity while the receiver reconstructs the original 28-bit word for local processing. The 66 MHz data-strobe rate permits frequent updates without exposing long single-ended traces. Implementers should validate timing at the slowest and fastest cable conditions, use the recommended receiver network, and keep the BGA power and ground distribution symmetrical.

🏭

High-Speed Digital Backplane Interface

The DS90CR286ASLC can support high-speed digital backplane links where a transmitter is located on one card and the receiver on another. Balanced LVDS pairs are well suited to controlled-impedance printed-circuit paths and help maintain signal integrity over distance. The receiver's 28-bit parallel output can connect to an FPGA or ASIC after proper timing control. Key design checks include differential impedance, pair-length matching, layer transitions, connector pin assignment, supply-plane noise, and the manufacturer's recommended 64-ball BGA land pattern.

Zusammenfassung der empfohlenen Produkte

DS90CR285 Compatible Channel Link transmitter Verwendet in: Industrial Data Acquisition, FPGA Parallel Data Interface, Test and Measurement Equipment, Communications and Networking Equipment, High-Speed Digital Backplane Interface DS90CR286A Same-family LVDS receiver option Verwendet in: Industrial Data Acquisition, Test and Measurement Equipment, Communications and Networking Equipment, High-Speed Digital Backplane Interface DS90CR286 Base-family receiver reference Verwendet in: FPGA Parallel Data Interface, Instrumentation and Control Systems DS90CR285A A-family transmitter for link pairing Verwendet in: Instrumentation and Control Systems
What is the DS90CR286ASLC?
The DS90CR286ASLC is a Texas Instruments 4-to-28 LVDS receiver for 66 MHz Channel Link communication. According to the Texas Instruments product information, it converts four LVDS data streams into parallel CMOS/TTL data and operates from a 3.3 V supply. The device is supplied in a 64-pin NFBGA package.
What is the operating voltage of DS90CR286ASLC?
The DS90CR286ASLC operates from 3 V to 3.6 V. The Texas Instruments product description identifies it as a +3.3 V rising-edge data-strobe LVDS receiver, while distributor specifications list the supply-voltage range as 3 V to 3.6 V. Confirm the final rail tolerance and decoupling requirements against the current manufacturer datasheet.
How many LVDS data channels does DS90CR286ASLC support?
The DS90CR286ASLC supports four LVDS data streams and converts them into 28 parallel CMOS/TTL data bits. The manufacturer describes the device as a 28-bit Channel Link receiver operating at 66 MHz. It is intended to work with a compatible DS90CR285-family transmitter and a downstream parallel-processing device.
What is the maximum data throughput of DS90CR286ASLC?
The DS90CR286ASLC supports up to 1.848 Gbps throughput, equivalent to 231 MB/s bandwidth as described in the device documentation. The 28-bit parallel output is received on the rising edge of the data strobe. Actual usable throughput depends on cable length, clocking, signal integrity, and the connected transmitter and receiver system.
Is DS90CR286ASLC a drop-in replacement for another LVDS receiver?
The DS90CR286ASLC can be evaluated as a replacement only when the candidate has the same 64-pin NFBGA footprint, pin-to-pin signal assignments, compatible supply voltage, and equivalent LVDS and parallel-output timing. The available cross-reference information identifies the DS90CR286A family but does not establish that every similarly named part is a drop-in replacement. Verify the pinout and timing specifications in the manufacturer datasheet before substitution.
What is the DS90CR286ASLC package?
The DS90CR286ASLC is packaged in a 64-pin NFBGA with an 8 x 8 mm outline. Distributor product information identifies the package as 64-NFBGA (8 x 8), and another listing identifies the component as a 64-LFBGA. The exact ball assignments and exposed-pad treatment should be checked in the current TI package drawing before PCB layout.
What is the difference between DS90CR286 and DS90CR286A?
The DS90CR286A is the revised product family listed by Texas Instruments, while DS90CR286ASLC is the orderable A-version receiver in the 64-pin NFBGA package. The available product descriptions both identify a +3.3 V, 66 MHz, 28-bit LVDS Channel Link receiver. Exact electrical and timing differences must be established from the revision-specific datasheets rather than assumed from the family name.
Where can I download the DS90CR286ASLC datasheet?
The official Texas Instruments DS90CR286 product page and datasheet link are the preferred download locations for DS90CR286ASLC documentation. The manufacturer also provides a product-information entry for DS90CR286A. Use the current DS90CR286 datasheet to verify the complete pin list, recommended application circuit, electrical characteristics, and package dimensions before design release.
Where can I find the DS90CR286ASLC pinout?
The DS90CR286ASLC pinout is defined in the Texas Instruments DS90CR286 datasheet. Because this part is a 64-ball BGA, use the manufacturer pin configuration and land-pattern information rather than assigning connections from a generic package diagram. Confirm power, ground, LVDS data inputs, clock input, parallel outputs, and any configuration or control balls directly from the datasheet.
How do I design the PCB layout for DS90CR286ASLC?
Route the four LVDS data pairs and the associated clock as controlled-impedance differential signals, keep the receiver close to the connector or transmitter, and minimize stubs and unnecessary vias. Follow the Texas Instruments datasheet for decoupling, LVDS input topology, BGA ball assignments, and exposed-pad connection. Check differential impedance, pair length matching, return-path continuity, and connector pinout during layout review.
What is the role of DS90CR286ASLC in a Channel Link system?
The DS90CR286ASLC serves as the receiving endpoint of a 28-bit Channel Link connection. It accepts four differential LVDS data streams, reconstructs 28 parallel CMOS/TTL data bits, and uses the data-strobe timing relationship to transfer data into a connected FPGA or other digital device. A compatible transmitter is required for a complete link.
Can DS90CR286ASLC be used with an FPGA parallel interface?
The DS90CR286ASLC is suitable for a parallel FPGA interface when the FPGA can accept 28 CMOS/TTL data bits and use the compatible rising-edge data-strobe signal. The design must support 3.3 V signaling, match the receiver's timing expectations, and provide a correctly terminated LVDS link. Validate setup and hold timing at the system level with the actual transmitter and cabling.
What should I check when selecting a replacement for DS90CR286ASLC?
Select a replacement by checking the 64-pin NFBGA footprint, ball-to-ball pin compatibility, 3 V to 3.6 V supply operation, four LVDS input channels, 28 parallel outputs, clock polarity, data-strobe timing, and operating-temperature requirements. The DS90CR286A family is the closest documented family candidate, but a true drop-in claim requires confirmation against the revision-specific manufacturer datasheets.
Is DS90CR286ASLC suitable for industrial equipment?
The DS90CR286ASLC is functionally suitable for industrial equipment that uses a 28-bit Channel Link interface and operates within the device's specified electrical limits. The available distributor and manufacturer information does not state the operating-temperature range, so temperature qualification, EMC requirements, power regulation, and isolation or protection requirements must be confirmed separately for the finished industrial system.
How do I request a quote for DS90CR286ASLC?
Use the Request a Quote form on this XAIPART product page to request current commercial terms, stock, and lead time for DS90CR286ASLC. The available distributor listings identify the exact part and package, but the quoted commercial result should be confirmed through the request form because supply and pricing can change.
What are the key specifications engineers should know about DS90CR286ASLC?
The key specifications are a 3 V to 3.6 V supply, four LVDS input streams, 28 parallel CMOS/TTL outputs, 66 MHz Channel Link operation, up to 1.848 Gbps throughput, 231 MB/s bandwidth, and a 64-pin NFBGA package in an 8 x 8 mm outline. According to Texas Instruments product information, the device is a rising-edge data-strobe receiver. Detailed timing, current, temperature, and pin limits should be taken from the current datasheet.

Technische Referenzdaten für DS90CR286ASLC – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose DS90CR286ASLC when the design needs a 3.3 V, four-lane LVDS receiver that converts a 28-bit Channel Link stream into parallel CMOS/TTL data at 66 MHz. Its 64-pin NFBGA package, 3 V to 3.6 V supply range, and documented 1.848 Gbps throughput suit compact FPGA, instrumentation, backplane, and industrial data-acquisition links. DS90CR286A is the closest same-family documented alternative and should be selected when the current TI product listing is preferred, but revision-specific electrical and timing differences must be checked. DS90CR285 and DS90CR285A are transmitters and make useful companion devices rather than receiver replacements. DS90CR216A is appropriate only when a 21-bit receiver and three LVDS lanes are acceptable; it is not equivalent in bus width or throughput. For every candidate, confirm ball assignments, clocking, timing, power, temperature, and footprint before approving a substitution.

Vergleich mit Alternativen

Parameter Dieses Produkt DS90CR286A DS90CR285 DS90CR285A DS90CR286 DS90CR216A
Package 64-pin NFBGA (8 x 8 mm) 64-pin NFBGA (8 x 8 mm) 64-pin NFBGA (8 x 8 mm) 64-pin NFBGA (8 x 8 mm) 64-pin NFBGA (8 x 8 mm) 64-pin NFBGA (8 x 8 mm)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Function 4-to-28 LVDS receiver 4-to-28 LVDS receiver 28-to-4 transmitter 28-to-4 transmitter 4-to-28 LVDS receiver 3-to-21 LVDS receiver
Data Width 28 bits 28 bits 28 bits 28 bits 28 bits 21 bits
LVDS Data Channels 4 4 4 4 4 3

Wichtigste Unterscheidungsmerkmale

  • Four-lane 28-bit receiver architecture (vs. DS90CR216A)
  • Documented 66 MHz Channel Link performance (vs. DS90CR216A)
  • A-version orderable family member (vs. DS90CR286)

Designhinweise

Use the current Texas Instruments DS90CR286 datasheet as the authority for the 64-ball NFBGA land pattern and pin assignments. Place the receiver close to the LVDS connector or transmitter, route each differential pair over a continuous reference plane, and avoid test pads, stubs, and layer changes where possible. Confirm differential impedance, pair-length tolerance, and BGA escape routing against the PCB stack-up.

Provide a clean 3.3 V rail within the documented 3 V to 3.6 V supply range. Place local bulk and high-frequency decoupling capacitors at the device's supply and ground balls using the manufacturer layout recommendation, while maintaining low-impedance power and ground distribution. Check supply-noise tolerance and decouple nearby switching circuits to prevent LVDS receiver jitter or false transitions.

Follow the manufacturer's recommended LVDS input network and termination arrangement. Keep the four data pairs and clock connection physically consistent, and verify differential impedance, connector loss, cable skew, and data-strobe timing across the intended operating environment. Do not substitute a generic termination or data-strobe arrangement without checking the exact DS90CR286A electrical characteristics.

A transmitter is not a receiver even when it uses the same family package. DS90CR285 and DS90CR285A are companion Channel Link transmitters, while DS90CR286ASLC is the receiver endpoint. Likewise, DS90CR216A uses a different 21-bit channel width. Confirm direction, clock polarity, supply levels, pin assignments, and timing before treating any family member as a substitution.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
No
Halogenfrei
Unknown
Konfliktmineralien
Unknown

A distributor listing states that the part contains lead and provides a RoHS field, but the complete compliance status cannot be confirmed from the available information. The manufacturer product and datasheet should be checked for current environmental, material, and quality declarations.

Daten verifiziert am: 2026-11-10 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

DS90CR286ASLC DS90CR286ASLC datasheet DS90CR286ASLC datasheet pdf DS90CR286ASLC pinout DS90CR286ASLC equivalent DS90CR286ASLC replacement DS90CR286ASLC cross reference DS90CR286ASLC schematic DS90CR286ASLC application circuit DS90CR286ASLC 64 NFBGA DS90CR286ASLC price DS90CR286ASLC stock Texas Instruments DS90CR286ASLC DS90CR286ASLC vs DS90CR286A

Verwandte Bauteile & Begriffe

Texas Instruments DS90CR286ASLC DS90CR286 DS90CR286A DS90CR285 DS90CR285A DS90CR216A LVDS low-voltage differential signaling Channel Link LVDS receiver parallel CMOS/TTL interface serial-to-parallel converter interface IC data strobe rising-edge data strobe 3.3 V logic 64-pin NFBGA BGA package surface mount 1.848 Gbps throughput 66 MHz operating frequency 28-bit parallel bus controlled-impedance routing RoHS REACH
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen