DS90CR286ASLC - 28-Bit LVDS Channel-Link Receiver | Texas Instruments
Référence : DS90CR286ASLC ✓ ActifDS90CR286ASLC Présentation
A Channel Link receiver is an interface IC that reconstructs parallel digital data from differential low-voltage differential signaling pairs. LVDS, or low-voltage differential signaling, is a high-speed electrical interface designed to reduce common-mode noise and support reliable data transfer over balanced conductors. The DS90CR286ASLC is therefore positioned within the interface-IC hierarchy, alongside parallel-to-serial and serial-to-parallel data converters, rather than with general-purpose logic or memory devices.
The main functional characteristics visible in the manufacturer and distributor information are the 4-to-28 LVDS-to-parallel conversion, 3 V to 3.6 V supply range, 66 MHz channel-link operating frequency, and up to 1.848 Gbps throughput or 231 MB/s bandwidth. The rising-edge data-strobe architecture allows the receiver to transfer 28 data bits in parallel while the companion DS90CR285 transmitter serializes the corresponding data stream. The use of LVDS can help reduce signal-integrity problems associated with single-ended high-speed interconnects.
The DS90CR286ASLC is used in industrial data acquisition, test and measurement equipment, instrumentation, communications equipment, and other systems requiring a high-speed parallel data interface. The receiver can be paired with a compatible transmitter and an FPGA or other parallel-processing device. Designers must account for the specified 3.3 V supply, correct LVDS input termination and topology, clock/data-strobe alignment, decoupling, and the package's thermal and layout requirements.
For PCB implementation, place the receiver close to the LVDS connector or transmitter, follow the manufacturer's recommended decoupling and controlled-impedance routing, and keep unused inputs in the states specified by the datasheet. The package pinout and detailed electrical limits should be taken from the current Texas Instruments DS90CR286 datasheet before final schematic and layout release. This page organizes the available technical information, sourcing guidance, comparison points, and design considerations around the DS90CR286ASLC.
Alternatives de remplacement direct pour DS90CR286ASLC — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
DS90CR286A
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR285
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DS90CR285A
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DS90CR286
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR216A
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DS90CR286ASLC Spécifications
| Product Type | LVDS to parallel CMOS/TTL receiver |
| Fonction | 4 differential LVDS data streams to 28 parallel data bits |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Channel-Link Operating Frequency | 66 MHz |
| Data Throughput | Up to 1.848 Gbps |
| Bandwidth | 231 MB/s |
| Number of Drivers | 4 |
| Number of Receivers | 28 |
| Receiver Type | LVDS receiver |
| Data Interface | CMOS/TTL parallel output |
| Signal Type | LVDS |
| Edge Type | Rising edge data strobe |
| Boîtier | 64-pin NFBGA, 8 x 8 mm |
| Packaging | Tube |
| Lead-Free Status | Contains lead per distributor listing |
Guide de configuration des broches du DS90CR286ASLC 64-pin nfbga, 8 x 8 mm
Configuration des broches du DS90CR286ASLC (boîtier 64-pin nfbga, 8 x 8 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DS90CR286ASLC.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DS90CR286ASLC convient pour 6 applications: Industrial Data Acquisition, FPGA Parallel Data Interface, Test and Measurement Equipment, Communications and Networking Equipment, Instrumentation and Control Systems, High-Speed Digital Backplane Interface.
Industrial Data Acquisition
The DS90CR286ASLC is suitable for industrial data-acquisition systems that receive 28-bit parallel data over a high-speed LVDS link. Its four differential LVDS inputs provide a noise-resistant transfer path between a remote transmitter and a controller, while the 66 MHz Channel Link rate supports data movement at up to 1.848 Gbps. The receiver can feed a parallel FPGA interface when voltage, clocking, and timing requirements match. Designers should use the manufacturer application guidance for input termination, controlled-impedance routing, BGA layout, and power decoupling.
Recommandé
FPGA Parallel Data Interface
The DS90CR286ASLC can serve as the LVDS-to-parallel interface between a high-speed link and an FPGA. Its 28 CMOS/TTL outputs provide a wide parallel bus, while the rising-edge data-strobe relationship supports deterministic sampling by the receiving logic. At 66 MHz, the documented throughput reaches 1.848 Gbps before protocol overhead. The FPGA design must match the receiver's 3.3 V interface, establish the correct data-strobe phase, and provide timing margin for cable skew, jitter, and board propagation delay.
Recommandé
Test and Measurement Equipment
The DS90CR286ASLC is appropriate for test and measurement instrumentation that transports a 28-bit measurement or control word over a high-speed differential link. LVDS reduces susceptibility to common-mode interference compared with a single-ended implementation, which is useful in equipment containing switching supplies, clocks, and analog sections. The receiver's 66 MHz operation and 231 MB/s bandwidth allow rapid parallel data transfer. Grounding, return paths, connector transitions, shielding, and power-supply separation should be designed to preserve signal integrity across the complete instrument enclosure.
Recommandé
Communications and Networking Equipment
The DS90CR286ASLC can be used in communications equipment that needs a reliable parallel data path between line-card or backplane electronics and a processing section. Four LVDS channels and 28 recovered data bits provide a compact interface for high-speed serialized transfers without exposing the full parallel bus to board-level noise. The 3.3 V operating range and NFBGA footprint support compact designs, but the system must verify connector and cable loss, clock recovery, grounding, and any regulatory EMC requirements before production use.
Recommandé
Instrumentation and Control Systems
The DS90CR286ASLC is useful in instrumentation and control systems that exchange wide parallel words with external sensors, programmable instruments, or remote I/O. A differential LVDS link can improve noise immunity while the receiver reconstructs the original 28-bit word for local processing. The 66 MHz data-strobe rate permits frequent updates without exposing long single-ended traces. Implementers should validate timing at the slowest and fastest cable conditions, use the recommended receiver network, and keep the BGA power and ground distribution symmetrical.
Recommandé
High-Speed Digital Backplane Interface
The DS90CR286ASLC can support high-speed digital backplane links where a transmitter is located on one card and the receiver on another. Balanced LVDS pairs are well suited to controlled-impedance printed-circuit paths and help maintain signal integrity over distance. The receiver's 28-bit parallel output can connect to an FPGA or ASIC after proper timing control. Key design checks include differential impedance, pair-length matching, layer transitions, connector pin assignment, supply-plane noise, and the manufacturer's recommended 64-ball BGA land pattern.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DS90CR286ASLC — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DS90CR286A | DS90CR285 | DS90CR285A | DS90CR286 | DS90CR216A |
|---|---|---|---|---|---|---|
| Package | 64-pin NFBGA (8 x 8 mm) | 64-pin NFBGA (8 x 8 mm) | 64-pin NFBGA (8 x 8 mm) | 64-pin NFBGA (8 x 8 mm) | 64-pin NFBGA (8 x 8 mm) | 64-pin NFBGA (8 x 8 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | 4-to-28 LVDS receiver | 4-to-28 LVDS receiver | 28-to-4 transmitter | 28-to-4 transmitter | 4-to-28 LVDS receiver | 3-to-21 LVDS receiver |
| Data Width | 28 bits | 28 bits | 28 bits | 28 bits | 28 bits | 21 bits |
| LVDS Data Channels | 4 | 4 | 4 | 4 | 4 | 3 |
Principaux différenciateurs
- Four-lane 28-bit receiver architecture (vs DS90CR216A)
- Documented 66 MHz Channel Link performance (vs DS90CR216A)
- A-version orderable family member (vs DS90CR286)
Notes de conception
Use the current Texas Instruments DS90CR286 datasheet as the authority for the 64-ball NFBGA land pattern and pin assignments. Place the receiver close to the LVDS connector or transmitter, route each differential pair over a continuous reference plane, and avoid test pads, stubs, and layer changes where possible. Confirm differential impedance, pair-length tolerance, and BGA escape routing against the PCB stack-up.
Provide a clean 3.3 V rail within the documented 3 V to 3.6 V supply range. Place local bulk and high-frequency decoupling capacitors at the device's supply and ground balls using the manufacturer layout recommendation, while maintaining low-impedance power and ground distribution. Check supply-noise tolerance and decouple nearby switching circuits to prevent LVDS receiver jitter or false transitions.
Follow the manufacturer's recommended LVDS input network and termination arrangement. Keep the four data pairs and clock connection physically consistent, and verify differential impedance, connector loss, cable skew, and data-strobe timing across the intended operating environment. Do not substitute a generic termination or data-strobe arrangement without checking the exact DS90CR286A electrical characteristics.
A transmitter is not a receiver even when it uses the same family package. DS90CR285 and DS90CR285A are companion Channel Link transmitters, while DS90CR286ASLC is the receiver endpoint. Likewise, DS90CR216A uses a different 21-bit channel width. Confirm direction, clock polarity, supply levels, pin assignments, and timing before treating any family member as a substitution.
Informations de conformité
A distributor listing states that the part contains lead and provides a RoHS field, but the complete compliance status cannot be confirmed from the available information. The manufacturer product and datasheet should be checked for current environmental, material, and quality declarations.