Texas Instruments

DS90LV012ATMFX - 400 Mbps LVDS Receiver | Texas Instruments

Teilenummer: DS90LV012ATMFX ✓ Aktiv
3-V CMOS Vdss SOT-23-5 (DBV) Package
MOQ: 1 |

DS90LV012ATMFX Übersicht

The Texas Instruments DS90LV012ATMFX is a 3-V LVDS single CMOS differential line receiver designed for high-speed digital interfaces. It accepts low-voltage differential signals, with a typical differential input level of 350 mV, and translates them into 3-V CMOS output levels. The receiver supports data rates up to 400 Mbps and is supplied in a 5-pin SOT-23 package, making it suitable for compact point-to-point communication equipment.

A low-voltage differential signaling receiver is an interface IC that converts a small differential voltage between two conductors into a single-ended CMOS logic signal. LVDS belongs to the broader differential line-driver and line-receiver family within interface ICs. Its differential signal method improves noise immunity by comparing the voltage on a positive input with the voltage on a negative input, which helps preserve data integrity when signals are transmitted across cables, backplanes, or circuit-board interconnects.

The DS90LV012ATMFX is intended for systems requiring low power dissipation, low noise, and high data rates. The manufacturer describes the device as a single CMOS differential-line receiver capable of operating in excess of 400 Mbps, corresponding to approximately 200 MHz. Its 3-V CMOS output interface makes it suitable for connecting LVDS physical-layer links to digital logic, controllers, FPGAs, ASICs, and other CMOS-based systems.

The receiver family provides fail-safe behavior for open, shorted, and terminated input conditions. Under those fail-safe conditions, the receiver output remains HIGH. This behavior helps system designers establish a defined state when a cable is disconnected, improperly terminated, or otherwise faulted. The DS90LV012A family also uses a pinout intended to simplify PCB layout, while the related DS90LT012A includes an input line-termination resistor for point-to-point applications.

Typical uses include industrial control links, test and measurement equipment, video and data transmission interfaces, embedded systems, and communications equipment. When placing the receiver in a design, preserve the differential pair geometry between the source and receiver, maintain suitable return paths, and follow the manufacturer’s input termination and bypass recommendations. The device must also be evaluated against the system’s required data rate, voltage levels, propagation-delay budget, and fault-state expectations.

This page combines the manufacturer’s device description, ordering information, package information, and cross-reference information into an application-focused guide. It highlights the distinction between the standard LVDS receiver and the related terminated DS90LT012A, clarifies the role of the SOT-23-5 package, and identifies the technical checks required before using DS90LV012ATMFX as a replacement candidate.

Drop-in-Alternativen für DS90LV012ATMFX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

DS90LV012ATMFX/NOPB

✅ Drop-In
📦 SOT-23-5 (DBV)
Same 400 Mbps and 3-V CMOS receiver ratings; the NOPB ordering code identifies the green, lead-free procurement option

📋 Referenzalternative (nicht im Katalog)

DS90LV012ATMF/NOPB

✅ Drop-In
📦 SOT-23-5 (DBV)
Same DS90LV012A electrical family, 400 Mbps rating, and 3-V CMOS output; ordering suffix and marking differ

📋 Referenzalternative (nicht im Katalog)

DS90LV011AQMFE/NOPB

✅ Drop-In
📦 SOT-23-5
Uses the same SOT-23-5 package class, but the receiver family and channel architecture differ; verify pin assignment and signal timing

📋 Referenzalternative (nicht im Katalog)

DS90LV012ATMFX Technische Daten

Product Type LVDS single CMOS differential line receiver
Maximum Data Rate 400 Mbps
Differential Input Signal 350 mV typical
Output Voltage Level 3-V CMOS
Receiver Architecture Single differential line receiver
Fail-Safe Input States Open, shorted, and 100-ohm terminated inputs
Fail-Safe Output State HIGH
Gehäuse SOT-23-5 (DBV)
Anzahl der Pins 5 pins
Betriebstemperaturbereich -40 °C to +85 °C
Montageart Surface mount
Input Termination External termination; related DS90LT012A includes an input termination resistor

DS90LV012ATMFX sot-23-5 (dbv) Pinbelegungsleitfaden

Pinbelegung für DS90LV012ATMFX (sot-23-5 (dbv)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für DS90LV012ATMFX im sot-23-5 (dbv)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für DS90LV012ATMFX.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

DS90LV012ATMFX ist geeignet für 6 Anwendungs: Industrial Point-to-Point Control Links, FPGA and ASIC Communication Interfaces, Test and Measurement Data Paths, Video and Display Control Interfaces, Communications Equipment Backplanes, Embedded Data Acquisition Modules.

🔧

Industrial Point-to-Point Control Links

The DS90LV012ATMFX fits industrial point-to-point control links that require a 400-Mbps LVDS receiver and a 3-V CMOS logic interface. It converts the typical 350 mV differential input into a single-ended CMOS output while operating across a -40 °C to +85 °C range. Use it when the transmitter, cable, and receiver form a controlled impedance-aware connection and the receiver has no integrated 100-ohm termination. The defined HIGH fail-safe output for open, shorted, or terminated inputs helps the controller recognize a disturbed link, although a complete system still needs deliberate fault detection and isolation.

🔧

FPGA and ASIC Communication Interfaces

The DS90LV012ATMFX is appropriate for FPGA or ASIC communication interfaces where an external LVDS physical layer terminates onto a 3-V CMOS logic domain. Its 400-Mbps data-rate capability provides ample margin for common parallel-to-serial control, status, and instrumentation links. Place the receiver close to the FPGA or ASIC and route the differential pair without stubs. Verify the receiver output voltage, propagation delay, setup and hold requirements, and the FPGA input threshold before releasing the layout. The device also provides a defined HIGH output during specified fail-safe input conditions.

🔧

Test and Measurement Data Paths

The DS90LV012ATMFX can be used in test and measurement equipment that transports high-rate status or trigger information over a compact LVDS connection. Its single-receiver architecture is useful when each signal pair has a dedicated endpoint, while the 400-Mbps rating supports data rates commonly required for synchronized acquisition and control electronics. Keep the differential trace pair coupled over its entire route, maintain a continuous reference plane, and minimize connector-to-receiver distance. Review the complete timing budget because the receiver output delay and source skew determine whether the downstream instrument can sample the data reliably.

🔧

Video and Display Control Interfaces

The DS90LV012ATMFX is suitable for auxiliary control or low-latency data links within professional video, display, and broadcast equipment. It accepts a low-amplitude differential signal and produces a 3-V CMOS output suitable for a controller or FPGA. The receiver’s small SOT-23-5 package helps conserve board area in dense processing cards, while the 400-Mbps capability supports high-speed command and status traffic. Ensure the video system’s LVDS voltage, termination, timing, and connector pin assignment agree with the receiver datasheet, and route away from switching-power and motor-control nodes.

🔧

Communications Equipment Backplanes

The DS90LV012ATMFX can serve as a board-edge receiver for short-haul communications links where differential signaling is used to reduce noise pickup and provide stable logic thresholds. A 400-Mbps single-channel receiver is suitable for dedicated control, management, or synchronization paths in network and embedded communications equipment. The external termination arrangement must match the intended topology, and the PCB should provide an uninterrupted reference plane beneath the differential pair. Verify the receiver’s propagation delay, supply requirements, and fail-safe behavior against the system’s loss-of-link requirements before production release.

🔧

Embedded Data Acquisition Modules

The DS90LV012ATMFX is appropriate for compact embedded data-acquisition modules that receive high-speed differential commands or synchronization signals from a remote sensor or processing board. Its 3-V CMOS output connects naturally to digital logic, and the 400-Mbps rating accommodates demanding transfer periods without requiring a large parallel bus. Keep the receiver away from high-current switching paths and use a controlled differential trace pair with matched length and minimal vias. If the link can be disconnected, software should use the specified HIGH fail-safe output as part of a deliberate safe-state strategy.

What is DS90LV012ATMFX?
The DS90LV012ATMFX is a Texas Instruments 3-V LVDS single CMOS differential line receiver for high-speed digital interfaces. According to the TI product page, the DS90LV012A family supports data rates up to 400 Mbps and is packaged in a 5-pin SOT-23 configuration. The device converts a small differential LVDS input into a 3-V CMOS logic output.
What is the maximum data rate of DS90LV012ATMFX?
The DS90LV012ATMFX supports data rates up to 400 Mbps, equivalent to approximately 200 MHz for a typical NRZ data stream. Texas Instruments describes the DS90LV012A and DS90LT012A as single CMOS differential receivers designed for high data rates and low power dissipation. Confirm channel-length and skew limits against the complete manufacturer datasheet.
What input voltage does DS90LV012ATMFX accept?
The DS90LV012ATMFX accepts a low-voltage differential input with a typical magnitude of 350 mV. The input consists of a positive and negative signal pair, and the receiver evaluates the difference between the two conductors. This differential sensing improves rejection of noise that affects both conductors equally.
Does DS90LV012ATMFX support fail-safe operation?
Yes. The DS90LV012A family supports open, shorted, and terminated input fail-safe conditions, and the receiver output remains HIGH in those conditions. This defined output state helps a system detect an interrupted or improperly terminated link rather than leaving the downstream CMOS logic in an indeterminate state.
Where can I download the DS90LV012ATMFX datasheet PDF?
The official Texas Instruments datasheet is available at https://www.ti.com/lit/ds/symlink/ds90lv012a.pdf. The document covers the DS90LV012A and DS90LT012A receivers, including the 3-V CMOS output architecture, 350 mV typical differential input, fail-safe behavior, ordering information, and application details. Use the manufacturer PDF for authoritative pin and electrical details.
Where is the DS90LV012ATMFX pinout located?
The DS90LV012ATMFX pinout is located in the DS90LV012A manufacturer datasheet. The exact ordering variant is identified in the TI part-details listing as a 5-pin SOT-23, DBV package. Use the pin-description table in that datasheet when assigning power, ground, differential inputs, and the CMOS output on the PCB.
Is DS90LV012ATMFX suitable for industrial control systems?
The DS90LV012ATMFX is suitable for industrial control systems that use a 3-V CMOS LVDS receiver and operate within the stated -40 °C to +85 °C temperature range. Its 400-Mbps capability supports high-speed point-to-point links. The overall industrial suitability still depends on system EMC requirements, isolation strategy, fault tolerance, and qualification of the assembled equipment.
How is DS90LV012ATMFX different from DS90LT012A?
DS90LV012ATMFX is the standard DS90LV012A-family receiver, while the related DS90LT012A includes an input line-termination resistor for point-to-point applications. Both accept low-voltage differential signals and produce 3-V CMOS outputs. The integrated termination should not be assumed to be interchangeable without checking the package pinout and required network topology.
DS90LV012ATMFX vs DS90LV011AQMFE/NOPB — which should be selected?
DS90LV012ATMFX should be selected when the design requires a single 3-V LVDS receiver with a 400-Mbps rating in the 5-pin SOT-23 package. The comparison candidate DS90LV011AQMFE/NOPB belongs to a different receiver family, so its channel count, package, logic levels, and pin assignment must be checked before substitution. It is not automatically a drop-in replacement.
When should I choose DS90LV012ATMFX over a terminated LVDS receiver?
Choose DS90LV012ATMFX when the board already provides the required LVDS termination and its SOT-23-5 pinout matches the layout. Choose a receiver with integrated termination when the design uses a simple point-to-point link and the manufacturer specifies the termination network. External termination can be selected for impedance control or shared-bus implementations.
What is the best drop-in replacement for DS90LV012ATMFX?
DS90LV012ATMFX/NOPB is the closest ordering form identified for the same Texas Instruments DS90LV012A receiver in the 5-pin SOT-23 package. It retains the 400-Mbps, 3-V CMOS receiver configuration, but purchasing-code and lead-finish details should be confirmed before approval. Cross-family parts require pin-by-pin and termination-network validation.
Can DS90LV012ATMFX be used with an FPGA or ASIC?
Yes, when the FPGA or ASIC input supports the receiver’s 3-V CMOS output and the system can meet LVDS timing requirements. The receiver can convert a differential link into a single-ended logic signal, but the designer must verify input thresholds, propagation delay, output timing, supply voltage, and signal-return requirements in the complete interface specification.
How should DS90LV012ATMFX be laid out for high-speed LVDS?
Place the receiver close to the connector or transceiver and route the differential pair as a tightly coupled impedance-controlled pair. Keep the pair length and differential skew minimized, provide a continuous reference plane, and avoid stubs or abrupt changes in trace geometry. The manufacturer states that the pinout is designed to simplify PCB layout.
How much power does DS90LV012ATMFX consume?
The DS90LV012A is designed for low power dissipation, but a specific power figure requires the operating voltage, supply-current value, and logic state. Use the Electrical Characteristics table in the TI datasheet for the applicable quiescent-current and dynamic-current conditions. A valid worst-case power estimate must include both supply current and the output transition rate.
Is DS90LV012ATMFX currently in stock and what is its lead time?
Current stock, quantity breaks, and lead time should be requested through the Request a Quote form on this page. The manufacturer part-details listing identifies the DS90LV012ATMFX/NOPB configuration, while distributor availability changes independently of the device specification. Submit the required quantity, package preference, and production schedule with the quote request.
Where can I buy DS90LV012ATMFX?
Use the Request a Quote form on this page to request DS90LV012ATMFX pricing, stock confirmation, minimum order quantity, and lead time. The manufacturer lists the device in the 5-pin SOT-23, DBV package with a -40 °C to +85 °C operating range. The quote request should include the exact MPN and required production quantity.

Technische Referenzdaten für DS90LV012ATMFX – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose DS90LV012ATMFX for a compact point-to-point interface requiring a single 400-Mbps LVDS receiver with a 3-V CMOS output. Its 5-pin SOT-23 package is useful in space-constrained control, test, communications, and embedded systems, while the specified fail-safe HIGH output provides a defined state for open, shorted, or terminated inputs. Choose DS90LV012ATMFX/NOPB when that green procurement ordering form is preferred for the same receiver configuration. DS90LV012ATMF/NOPB belongs to the same electrical family and package class but uses a different ordering suffix, so markings and purchasing requirements should be checked. Consider DS90LT012A instead when an integrated input termination is specifically required for a point-to-point link, but do not assume its pinout and termination function are interchangeable. Use DS90LV011AQMFE/NOPB only after verifying its channel architecture, timing, logic levels, and pin functions against the PCB footprint.

Vergleich mit Alternativen

Parameter Dieses Produkt DS90LV012ATMFX/NOPB DS90LV012ATMF/NOPB DS90LV011AQMFE/NOPB
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOT-23-5 (DBV) SOT-23-5 (DBV) SOT-23-5 (DBV) SOT-23-5
Product Type Single LVDS differential line receiver Single LVDS differential line receiver Single LVDS differential line receiver LVDS interface receiver
Number of Pins 5 pins 5 pins 5 pins 5 pins

Wichtigste Unterscheidungsmerkmale

  • Direct ordering counterpart with the same electrical configuration (vs. DS90LV012ATMFX/NOPB)
  • Same DS90LV012A family and 400-Mbps receiver performance (vs. DS90LV012ATMF/NOPB)
  • Single-channel architecture simplifies point-to-point routing (vs. DS90LV011AQMFE/NOPB)

Designhinweise

Route the differential input as a tightly coupled pair over a continuous reference plane. Keep the receiver close to the connector or line-driver output, minimize stubs and layer transitions, and match the pair geometry to the intended board impedance. Avoid placing the pair alongside switching-power nodes, clock sources, or high-speed memory traces because those signals can couple into the small differential input.

Determine whether the board requires an external 100-ohm termination before finalizing the schematic. The DS90LV012A family is related to the DS90LT012A version that includes an input line-termination resistor for point-to-point use, but the standard DS90LV012A should not be assumed to contain that resistor. Confirm the exact pinout and termination arrangement in the manufacturer datasheet before fabrication.

Do not treat the HIGH fail-safe output as a substitute for a complete link-error strategy. The receiver defines its state for open, shorted, and terminated inputs, but downstream software still needs a timeout, heartbeat, or physical-layer fault indication. Also verify that the source uses compatible 350 mV typical LVDS signaling and that the cable, connector, and receiver topology are appropriate for the intended data rate.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance attributes require confirmation from the manufacturer product page or the current manufacturer datasheet. The NOPB ordering code is an ordering identifier and is not treated by itself as proof of a specific compliance status.

Ähnliche Suchanfragen

ds90lv012atmfx nopb DS90LV012ATMFX datasheet DS90LV012ATMFX datasheet pdf DS90LV012ATMFX pinout DS90LV012ATMFX equivalent DS90LV012ATMFX replacement DS90LV012ATMFX cross reference DS90LV012ATMFX vs DS90LV011AQMFE DS90LV012ATMFX SOT-23-5 receiver DS90LV012ATMFX 400 Mbps LVDS DS90LV012ATMFX price DS90LV012ATMFX stock

Verwandte Bauteile & Begriffe

Texas Instruments DS90LV012ATMFX DS90LV012ATMFX/NOPB DS90LV012ATMF/NOPB DS90LV011AQMFE/NOPB DS90LV012A DS90LT012A LVDS Low Voltage Differential Signaling differential line receiver interface IC 3-V CMOS 400 Mbps 350 mV differential input SOT-23-5 DBV package surface mount fail-safe receiver point-to-point link signal integrity differential pair industrial control FPGA interface test and measurement RoHS REACH AEC-Q100
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen