DS90LV012ATMFX - 400 Mbps LVDS Receiver | Texas Instruments
MPN: DS90LV012ATMFX ✓ AktifDS90LV012ATMFX Ringkasan
A low-voltage differential signaling receiver is an interface IC that converts a small differential voltage between two conductors into a single-ended CMOS logic signal. LVDS belongs to the broader differential line-driver and line-receiver family within interface ICs. Its differential signal method improves noise immunity by comparing the voltage on a positive input with the voltage on a negative input, which helps preserve data integrity when signals are transmitted across cables, backplanes, or circuit-board interconnects.
The DS90LV012ATMFX is intended for systems requiring low power dissipation, low noise, and high data rates. The manufacturer describes the device as a single CMOS differential-line receiver capable of operating in excess of 400 Mbps, corresponding to approximately 200 MHz. Its 3-V CMOS output interface makes it suitable for connecting LVDS physical-layer links to digital logic, controllers, FPGAs, ASICs, and other CMOS-based systems.
The receiver family provides fail-safe behavior for open, shorted, and terminated input conditions. Under those fail-safe conditions, the receiver output remains HIGH. This behavior helps system designers establish a defined state when a cable is disconnected, improperly terminated, or otherwise faulted. The DS90LV012A family also uses a pinout intended to simplify PCB layout, while the related DS90LT012A includes an input line-termination resistor for point-to-point applications.
Typical uses include industrial control links, test and measurement equipment, video and data transmission interfaces, embedded systems, and communications equipment. When placing the receiver in a design, preserve the differential pair geometry between the source and receiver, maintain suitable return paths, and follow the manufacturer’s input termination and bypass recommendations. The device must also be evaluated against the system’s required data rate, voltage levels, propagation-delay budget, and fault-state expectations.
This page combines the manufacturer’s device description, ordering information, package information, and cross-reference information into an application-focused guide. It highlights the distinction between the standard LVDS receiver and the related terminated DS90LT012A, clarifies the role of the SOT-23-5 package, and identifies the technical checks required before using DS90LV012ATMFX as a replacement candidate.
Pilihan pengganti yang segera untuk DS90LV012ATMFX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
DS90LV012ATMFX/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90LV012ATMF/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90LV011AQMFE/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90LV012ATMFX Spesifikasi
| Product Type | LVDS single CMOS differential line receiver |
| Maximum Data Rate | 400 Mbps |
| Differential Input Signal | 350 mV typical |
| Output Voltage Level | 3-V CMOS |
| Receiver Architecture | Single differential line receiver |
| Fail-Safe Input States | Open, shorted, and 100-ohm terminated inputs |
| Fail-Safe Output State | HIGH |
| Kemasan | SOT-23-5 (DBV) |
| Bilangan Pin | 5 pins |
| Gambaran Suhu Operasi | -40 °C to +85 °C |
| Jenis Pemasangan | Surface mount |
| Input Termination | External termination; related DS90LT012A includes an input termination resistor |
Panduan Konfigurasi Pin DS90LV012ATMFX sot-23-5 (dbv)
Konfigurasi pin untuk DS90LV012ATMFX (sot-23-5 (dbv) pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DS90LV012ATMFX.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DS90LV012ATMFX patut untuk 6 aplikasis: Industrial Point-to-Point Control Links, FPGA and ASIC Communication Interfaces, Test and Measurement Data Paths, Video and Display Control Interfaces, Communications Equipment Backplanes, Embedded Data Acquisition Modules.
Industrial Point-to-Point Control Links
The DS90LV012ATMFX fits industrial point-to-point control links that require a 400-Mbps LVDS receiver and a 3-V CMOS logic interface. It converts the typical 350 mV differential input into a single-ended CMOS output while operating across a -40 °C to +85 °C range. Use it when the transmitter, cable, and receiver form a controlled impedance-aware connection and the receiver has no integrated 100-ohm termination. The defined HIGH fail-safe output for open, shorted, or terminated inputs helps the controller recognize a disturbed link, although a complete system still needs deliberate fault detection and isolation.
FPGA and ASIC Communication Interfaces
The DS90LV012ATMFX is appropriate for FPGA or ASIC communication interfaces where an external LVDS physical layer terminates onto a 3-V CMOS logic domain. Its 400-Mbps data-rate capability provides ample margin for common parallel-to-serial control, status, and instrumentation links. Place the receiver close to the FPGA or ASIC and route the differential pair without stubs. Verify the receiver output voltage, propagation delay, setup and hold requirements, and the FPGA input threshold before releasing the layout. The device also provides a defined HIGH output during specified fail-safe input conditions.
Test and Measurement Data Paths
The DS90LV012ATMFX can be used in test and measurement equipment that transports high-rate status or trigger information over a compact LVDS connection. Its single-receiver architecture is useful when each signal pair has a dedicated endpoint, while the 400-Mbps rating supports data rates commonly required for synchronized acquisition and control electronics. Keep the differential trace pair coupled over its entire route, maintain a continuous reference plane, and minimize connector-to-receiver distance. Review the complete timing budget because the receiver output delay and source skew determine whether the downstream instrument can sample the data reliably.
Video and Display Control Interfaces
The DS90LV012ATMFX is suitable for auxiliary control or low-latency data links within professional video, display, and broadcast equipment. It accepts a low-amplitude differential signal and produces a 3-V CMOS output suitable for a controller or FPGA. The receiver’s small SOT-23-5 package helps conserve board area in dense processing cards, while the 400-Mbps capability supports high-speed command and status traffic. Ensure the video system’s LVDS voltage, termination, timing, and connector pin assignment agree with the receiver datasheet, and route away from switching-power and motor-control nodes.
Communications Equipment Backplanes
The DS90LV012ATMFX can serve as a board-edge receiver for short-haul communications links where differential signaling is used to reduce noise pickup and provide stable logic thresholds. A 400-Mbps single-channel receiver is suitable for dedicated control, management, or synchronization paths in network and embedded communications equipment. The external termination arrangement must match the intended topology, and the PCB should provide an uninterrupted reference plane beneath the differential pair. Verify the receiver’s propagation delay, supply requirements, and fail-safe behavior against the system’s loss-of-link requirements before production release.
Embedded Data Acquisition Modules
The DS90LV012ATMFX is appropriate for compact embedded data-acquisition modules that receive high-speed differential commands or synchronization signals from a remote sensor or processing board. Its 3-V CMOS output connects naturally to digital logic, and the 400-Mbps rating accommodates demanding transfer periods without requiring a large parallel bus. Keep the receiver away from high-current switching paths and use a controlled differential trace pair with matched length and minimal vias. If the link can be disconnected, software should use the specified HIGH fail-safe output as part of a deliberate safe-state strategy.
Data referensi kejuruteraan untuk DS90LV012ATMFX — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DS90LV012ATMFX/NOPB | DS90LV012ATMF/NOPB | DS90LV011AQMFE/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 (DBV) | SOT-23-5 (DBV) | SOT-23-5 (DBV) | SOT-23-5 |
| Product Type | Single LVDS differential line receiver | Single LVDS differential line receiver | Single LVDS differential line receiver | LVDS interface receiver |
| Number of Pins | 5 pins | 5 pins | 5 pins | 5 pins |
Penyeberangsung Jelas
- Direct ordering counterpart with the same electrical configuration (vsDS90LV012ATMFX/NOPB)
- Same DS90LV012A family and 400-Mbps receiver performance (vsDS90LV012ATMF/NOPB)
- Single-channel architecture simplifies point-to-point routing (vsDS90LV011AQMFE/NOPB)
Catatan Desain
Route the differential input as a tightly coupled pair over a continuous reference plane. Keep the receiver close to the connector or line-driver output, minimize stubs and layer transitions, and match the pair geometry to the intended board impedance. Avoid placing the pair alongside switching-power nodes, clock sources, or high-speed memory traces because those signals can couple into the small differential input.
Determine whether the board requires an external 100-ohm termination before finalizing the schematic. The DS90LV012A family is related to the DS90LT012A version that includes an input line-termination resistor for point-to-point use, but the standard DS90LV012A should not be assumed to contain that resistor. Confirm the exact pinout and termination arrangement in the manufacturer datasheet before fabrication.
Do not treat the HIGH fail-safe output as a substitute for a complete link-error strategy. The receiver defines its state for open, shorted, and terminated inputs, but downstream software still needs a timeout, heartbeat, or physical-layer fault indication. Also verify that the source uses compatible 350 mV typical LVDS signaling and that the cable, connector, and receiver topology are appropriate for the intended data rate.
Maklumat Kesediaan
Compliance attributes require confirmation from the manufacturer product page or the current manufacturer datasheet. The NOPB ordering code is an ordering identifier and is not treated by itself as proof of a specific compliance status.