Renesas Electronics

ICS527R-02 - 160MHz Zero-Delay Clock Slicer | Renesas

Teilenummer: ICS527R-02 ✓ Aktiv
28-SSOP, 0.154 inch width, 3.90 mm width Package 160 MHz Speed
MOQ: 1 |

ICS527R-02 Übersicht

The Renesas Electronics ICS527R-02 is a user-configurable clock slicer and zero-delay buffer with a maximum frequency of 160 MHz, one PECL input, and CMOS clock outputs, housed in a 28-SSOP package. It aligns the rising edges of PECLIN and FBIN according to divider ratios programmed by external reference and feedback components, allowing nearly any related output frequency to be generated from a PECL source clock.

A clock slicer is a specialized timing IC that divides and recombines clock signals to provide adjustable phase relationships. Clock slicers sit within the clock and timing hierarchy as clock buffers and fanout devices, where low skew and predictable edge alignment are more important than simply regenerating a clock. The ICS527-02 family uses a PLL-based architecture to create zero-skew PECL-to-CMOS clocking relationships for communications, processor, and data-conversion systems.

The ICS527R-02 supports a maximum operating frequency of 160 MHz and has one clock circuit. Its user-configurable reference and feedback dividers allow multiplication or division of the input clock, while the zero-delay architecture minimizes the skew between the relevant rising edges. PECL input support is useful in high-speed telecommunications and industrial clocking systems where the source clock is already distributed using ECL-family logic levels.

Operationally, the device accepts a PECL reference clock and returns related CMOS clock outputs. The two CMOS outputs support fanout and clock distribution, reducing the need for separate logic buffers when several domains require the same derived timing signal. Zero-delay operation is intended for systems in which source and feedback clocks must be phase-aligned with very little edge displacement.

Typical uses include telecom line-card clocking, data-converter clock generation, processor reference-clock distribution, network-interface timing, and industrial control systems. The 160 MHz ceiling makes the ICS527R-02 most appropriate for designs operating below that limit, while the 28-SSOP package supports compact, surface-mounted assemblies.

PCB implementation requires careful treatment of high-speed clock inputs and outputs. Keep PECL traces short, provide a continuous reference plane, avoid stubs, and place termination and decoupling components close to the device. Confirm input/output timing, divider ratios, and supply sequencing against the manufacturer datasheet before releasing production artwork.

This product page combines the manufacturer function description with package, frequency, interface, and architecture details, then adds application guidance, drop-in replacement limits, comparison parameters, and practical layout considerations. These engineering-oriented notes help distinguish a true PCB-compatible replacement from a merely similar clock-buffer product.

Drop-in-Alternativen für ICS527R-02 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

527R-02LF

✅ Drop-In
📦 28-SSOP
Same ICS527-02 family and 28-SSOP terminal/package arrangement; maximum frequency is shown as 140 MHz versus 160 MHz, a 12.5% reduction

📋 Referenzalternative (nicht im Katalog)

ICS527R-02T

✅ Drop-In
📦 28-SSOP
Same ICS527R-02 clock-slicer configuration and 28-SSOP footprint; suffix-specific packing and qualification details require confirmation

📋 Referenzalternative (nicht im Katalog)

ICS527R-01I

✅ Drop-In
📦 28-SSOP
Same 28-SSOP clock-slicer package and closely related family; the -01 divider configuration differs from -02 and must be checked against the required ratio

📋 Referenzalternative (nicht im Katalog)

ICS527R-02 Technische Daten

Product Type User-configurable clock slicer and zero-delay buffer
Maximum Frequency 160 MHz
Number of Circuits 1 circuit
Input Logic Type PECL
Output Logic Type CMOS
Input-to-Output Ratio 1:2
PLL Yes
Architecture PLL-based clock slicer with zero-skew alignment
Anzahl der Ausgänge 2 true outputs
Number of Inverted Outputs 0 inverted outputs
Gehäuse 28-SSOP, 0.154 inch width, 3.90 mm width
Montageart Surface mount
Edge Alignment Rising edges aligned on PECLIN and FBIN
Ausgangskonfiguration Multiplied or divided from the PECL input clock

ICS527R-02 28-ssop, 0.154 inch width, 3.90 mm width Pinbelegungsleitfaden

Pinbelegung für ICS527R-02 (28-ssop, 0.154 inch width, 3.90 mm width-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für ICS527R-02 im 28-ssop, 0.154 inch width, 3.90 mm width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ICS527R-02.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ICS527R-02 ist geeignet für 6 Anwendungs: Telecommunications Clock Distribution, Data Converter Clocking, Processor Reference Clock, Industrial Control Timing, Audio Converter Clocking, Network Interface Timing.

🌐

Telecommunications Clock Distribution

The ICS527R-02 fits telecom clocking systems that receive a PECL reference and require related CMOS clocks with controlled edge relationships. Its maximum frequency of 160 MHz supports high-speed line-card, framer, and serial-interface timing, while two true outputs can distribute the derived clock within one subsystem. Configure the reference and feedback dividers for the required relationship, then keep PECLIN and FBIN routes short over a continuous ground plane. The main engineering trade-off is that a multiplier or divider must remain within the 160 MHz operating ceiling.

⚡

Data Converter Clocking

Use the ICS527R-02 when an ADC or DAC system needs a configurable CMOS clock derived from a PECL source. The zero-delay slicer architecture can align PECLIN and FBIN rising edges, helping create the exact related clock needed by sampling or conversion timing. Its 160 MHz maximum frequency covers many moderate- and high-speed converters, and the two outputs can feed converter and supporting digital logic. Select divider values that keep every derived clock below the operating limit and preserve the required conversion sampling relationship.

🖥️

Processor Reference Clock

The ICS527R-02 can derive and distribute a processor-related clock from a PECL-compatible source. Two true CMOS outputs allow a single device to feed related clock domains, reducing the number of separate buffers when the timing relationship must be controlled. The PLL-based divider arrangement is valuable when the downstream processor requires a ratio other than 1:1. Verify acquisition and hold requirements at the receiver, maintain continuous return paths, and ensure the selected output ratio does not exceed the 160 MHz device limit.

🏭

Industrial Control Timing

Industrial control modules can use the ICS527R-02 when multiple subsystems require related clock outputs and the source interface is PECL. The configurable divider ratios help adapt one incoming clock to several timing domains, while the zero-skew architecture supports predictable alignment. Operating below 160 MHz provides suitable performance for many control, monitoring, and communication subsystems. In factory equipment, isolate clock routing from noisy power stages, provide local decoupling, and validate timing margins over temperature and process variations.

🎧

Audio Converter Clocking

The ICS527R-02 is appropriate for audio systems that require a CMOS clock with a controlled relationship to a PECL-derived reference. Its two outputs can feed related converter and digital sections, and its user-configurable dividers support clock-ratio selection where a simple fanout is insufficient. For audio converters, keep the clock source and return path compact, minimize coupling from switching regulators and digital clocks, and verify the required sampling ratio. Confirm jitter performance for the complete clock-generation path rather than relying only on the 160 MHz frequency rating.

🌐

Network Interface Timing

The ICS527R-02 can support network-interface subsystems that need a PECL input converted into related CMOS clocks for controller, transceiver, or serializer logic. The maximum 160 MHz operating frequency is suitable for many interface clock trees, and two outputs reduce fanout complexity when the destinations must remain phase-related. Control impedance, avoid unnecessary vias, and separate the clock route from high-energy switching nodes. Validate setup and hold at each receiver because device skew and board routing contribute to the total timing margin.

What is the ICS527R-02 and what does it do?
The ICS527R-02 is a user-configurable PLL-based clock slicer and zero-delay buffer that generates CMOS clock outputs from a PECL input clock. According to the Renesas 527-02 datasheet, it aligns the rising edges of PECLIN with FBIN according to the selected reference and feedback divider ratios. The device supports one clock circuit, provides two true CMOS outputs, and operates up to 160 MHz in a 28-SSOP package.
What is the maximum frequency of the ICS527R-02?
The ICS527R-02 supports a maximum clock frequency of 160 MHz. This rating is stated in the Renesas 527-02 datasheet and distributor product listings. It is important to evaluate output-divider configurations as well as the input frequency because a multiplied output cannot exceed the device's supported operating range. The 160 MHz figure should therefore be treated as the design ceiling, not as a guarantee for every divider ratio.
What are the input and output logic levels of ICS527R-02?
The ICS527R-02 accepts a PECL reference input and produces CMOS clock outputs. The Renesas 527-02 datasheet identifies the PECLIN and FBIN timing relationship used for edge alignment, while product listings classify the output as CMOS. This interface combination is intended for systems that receive ECL-family clocking and require lower-voltage CMOS timing signals for downstream logic.
How does the ICS527R-02 zero-delay function work?
The ICS527R-02 uses a PLL-based clock-slicer architecture to align rising edges on PECLIN and FBIN. Renesas states that the alignment ratio is determined by the reference and feedback dividers, allowing the output clock to be multiplied or divided relative to the input. Zero-delay refers to the near-zero edge-skew objective between the designated clock paths; it does not mean that every output edge is simultaneously present at the input pins.
Where can I download the ICS527R-02 datasheet PDF?
The official ICS527R-02 family datasheet is available from the Renesas 527-02 document page at https://www.renesas.com/en/document/dst/527-02-datasheet. It is the primary document for pin assignments, divider configuration, electrical limits, application circuits, and timing characteristics. Use the manufacturer document rather than relying on a distributor summary when designing the SSOP-28 footprint or configuring the clock-divider network.
Where can I find the ICS527R-02 pinout and SSOP-28 footprint?
Use the pin-description table and land-pattern drawing in the Renesas 527-02 datasheet to determine the ICS527R-02 pinout and SSOP-28 footprint. The verified product records identify a 28-SSOP package, but they do not reproduce all terminal names and numbering. Confirm every power, ground, PECL, feedback, reference, and CMOS-output connection against the manufacturer document before placing components or assigning PCB nets.
What is the difference between ICS527R-02 and ICS527R-02T?
The ICS527R-02T is presented as the same ICS527R-02 clock-slicer family configuration in a different orderable suffix, and the distributor listing associates it with the 28-SSOP device family. The verified records do not quantify a functional difference between the two suffixes, so engineers should treat suffix-specific temperature, packing, and marking information as unconfirmed until checked in the ordering information. The ICS527R-02 remains the baseline catalog designation.
Can ICS527R-02T replace ICS527R-02 without PCB changes?
ICS527R-02T is a same-family candidate for replacement because distributor records associate it with the 28-SSOP ICS527R-02 family. However, suffix-specific qualification, temperature grade, packing, and marking must be compared with the installed part before production use. The verified records do not establish a complete commercial interchange matrix, so verify the manufacturer ordering table and inspect the existing PCB and assembly requirements.
What is the best drop-in replacement for ICS527R-02?
The closest documented same-brand candidates are 527R-02LF and ICS527R-02T, both associated with the ICS527-02 family and 28-SSOP format in the cross-reference records. A cross-brand drop-in replacement was not established by the verified results. Before substituting any candidate, confirm that the PECL interface, CMOS outputs, divider configuration, pin functions, supply requirements, frequency rating, and temperature grade match the original design.
What can replace the ICS527R-02?
The most defensible replacement path begins with the 527R-02LF and ICS527R-02T family orderings identified in the cross-reference results. Both remain tied to the ICS527-02 clock-slicer architecture, but a production substitution requires a manufacturer-level review of pinout, electrical limits, divider behavior, and orderable suffix. No verified cross-brand part was found that establishes the same PCB footprint and complete electrical behavior.
Is ICS527R-02 suitable for high-speed communications clocking?
The ICS527R-02 is suitable for communications clocking when the design operates within its 160 MHz limit and uses a PECL source with compatible CMOS clock loads. Its PLL-based zero-delay architecture supports edge alignment, while the two CMOS outputs can serve related downstream domains. Practical signal-integrity work is still required to control clock skew, jitter, reflections, supply noise, and crosstalk on the board.
When should I choose ICS527R-02 instead of a conventional clock buffer?
Choose the ICS527R-02 when the design must derive a multiplied or divided CMOS clock while maintaining a controlled edge relationship between PECLIN and FBIN. A conventional fanout buffer is simpler when only regeneration and distribution are required, without adjustable ratios or zero-skew alignment. The ICS527R-02 adds PLL-based flexibility, but that flexibility also requires careful divider, feedback, termination, and layout design.
How should I design the PCB layout for ICS527R-02?
Place the input, feedback, reference, and bypass connections close to their intended IC pins, and route high-speed clock traces over a continuous ground reference plane. Avoid long stubs and unnecessary test-point branches, match clock topology to the reference design, and place termination networks where they can minimize reflections. The Renesas 527-02 application guidance should govern final trace geometry and component placement.
Where can I buy ICS527R-02 and check current lead time?
Use the Request a Quote form on this page to ask about ICS527R-02 availability, order quantity, and current lead time. The verified distributor record confirms a 28-SSOP catalog listing but does not print a qualifying quantity-price table or a manufacturing lead time. A procurement request should state the required suffix, quantity, date code, and whether reel, tray, or another approved packing method is needed.
What is the lifecycle status and compliance of ICS527R-02?
The current lifecycle classification for ICS527R-02 should be confirmed through the manufacturer product and ordering records before a long-term production commitment. The verified records identify the device as a Renesas Electronics clock slicer but do not provide a definitive lifecycle statement or complete RoHS, REACH, AEC-Q100, lead-free, or halogen-free declarations. Request the current environmental and qualification documentation for the exact orderable part.

Technische Referenzdaten für ICS527R-02 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ICS527R-02 when the design requires a PECL-to-CMOS clock slicer, a PLL-based divider arrangement, two true outputs, and operation as high as 160 MHz. It is especially useful when rising edges on PECLIN and FBIN must be aligned rather than merely distributed. Select 527R-02LF when its 140 MHz ceiling provides enough margin and the orderable suffix is otherwise suitable. ICS527R-02T is the closest same-family option for an assembly comparison because it retains the -02 configuration and 28-SSOP footprint, but packing and qualification details should be confirmed. ICS527R-01I is appropriate only after checking its divider ratio against the target design. No cross-brand substitution should be considered without a manufacturer-confirmed pinout, electrical, timing, and package match.

Vergleich mit Alternativen

Parameter Dieses Produkt 527R-02LF ICS527R-02T ICS527R-01I
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 28-SSOP 28-SSOP - same package 28-SSOP - same package 28-SSOP - same package
Product Type Clock slicer and zero-delay buffer Clock slicer and zero-delay buffer Clock slicer and zero-delay buffer Clock slicer and zero-delay buffer
Divider Configuration -02 family configuration -02 family configuration -02 family configuration -01 family configuration

Wichtigste Unterscheidungsmerkmale

  • Higher documented maximum frequency than 527R-02LF (vs. 527R-02LF)
  • Direct ordering within the same -02 configuration (vs. ICS527R-02T)
  • Same package and core clock-slicer architecture as the -01 family (vs. ICS527R-01I)

Designhinweise

Treat PECLIN, FBIN, and the CMOS clock outputs as high-speed nets. Route them over a continuous ground plane, minimize vias and stubs, and keep input termination close to the receiving pin. Place the PLL support and bypass components according to the manufacturer reference design. The zero-delay relationship is measured at the device pins, so asymmetric traces can reintroduce board skew even when the chip is configured correctly.

Use the manufacturer's recommended supply topology and place local high-frequency bypass capacitance immediately across the appropriate supply and ground pins. Keep switching-regulator routing and magnetic fields away from FBIN because feedback-edge displacement can affect divider operation and alignment. Confirm capacitor voltage rating, DC-bias behavior, and stability requirements using the datasheet rather than substituting ceramic types by capacitance alone.

Do not interpret the 160 MHz rating as permission to drive every divider configuration at 160 MHz. Calculate the highest internal or output frequency from the selected reference and feedback ratios and compare it with all timing and operating limits. Also verify that the chosen suffix matches the required temperature grade, packing, and qualification. Reordering rules and suffix meanings must be checked in the current manufacturer ordering information.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The verified records do not include definitive environmental or automotive qualification declarations for this exact orderable part. Request the current manufacturer product-compliance documents before production release.

Ähnliche Suchanfragen

ICS527R-02 datasheet ICS527R-02 pinout ICS527R-02 datasheet pdf ICS527R-02 equivalent ICS527R-02 replacement ICS527R-02 cross reference ICS527R-02 vs 527R-02LF Renesas ICS527R-02 ICS527R-02 160MHz clock slicer ICS527R-02 SSOP-28 footprint ICS527R-02 PECL CMOS clock ICS527R-02 telecommunications clocking ICS527R-02 price ICS527R-02 stock ICS527R-02 application circuit

Verwandte Bauteile & Begriffe

Renesas Electronics ICS527R-02 527R-02LF ICS527R-02T ICS527R-01I clock slicer zero-delay buffer clock buffer fanout buffer PLL-based clock clock and timing IC PECL CMOS clock output zero-skew alignment rising-edge alignment feedback divider reference divider 160 MHz clock 28-SSOP surface-mount package telecommunications clocking data-converter clocking processor reference clock industrial control timing
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen