Renesas Electronics

ICS542MIT - 1:2 156 MHz Clock Fanout Buffer | Renesas

Teilenummer: ICS542MIT ✓ Aktiv
3 V to 5.5 V Vdss 8-SOIC, 3.90 mm width Package 156 MHz Speed
MOQ: 1 |

ICS542MIT Übersicht

Renesas Electronics ICS542MIT is a clock fanout buffer and divider integrated circuit with a 1:2 division ratio, a maximum operating frequency of 156 MHz, and an 8-SOIC package measuring 3.90 mm in width. It accepts a CMOS clock input and provides two three-state CMOS outputs, making it suitable for distributing a divided clock to multiple digital loads.

A clock fanout buffer is a clock and timing IC that reproduces or distributes a clock signal while controlling impedance, loading, and signal timing. The ICS542MIT belongs to the broader clock buffer and driver hierarchy, where clock distribution devices isolate a source from downstream capacitance and provide predictable edge propagation into logic circuits. Its 3 V to 5.5 V supply range allows operation across common low-voltage digital systems.

The device combines a 1:2 divider function with clock fanout capability. Its three-state CMOS outputs can place individual outputs into a high-impedance state when the receiving circuitry does not need a clock, while the 156 MHz maximum frequency supports common communications, control, and digital-logic clock domains. The 8-SOIC package is suitable for conventional surface-mount PCB assembly and offers a practical upgrade path for designs requiring more than a direct clock connection.

Clock distribution requires careful attention to edge rate, output loading, return path continuity, and trace length. The three-state outputs make output-enable control relevant to system power management and bus segmentation. Because the ICS542MIT divides the input clock, downstream logic should be evaluated against the divided output frequency rather than assuming the source frequency appears unchanged at the receiver.

Typical applications include communication equipment, control systems, test and measurement products, and general-purpose digital platforms that require one input clock to feed two destinations. The device is particularly useful where one subsystem needs a divided clock or where multiple clock domains must receive independently controlled outputs. Its 156 MHz ceiling also makes it applicable to systems operating below that frequency without requiring a higher-speed clock distribution architecture.

When laying out the circuit, keep clock traces short, provide a continuous ground reference, and place decoupling close to the supply pins. Treat output-enable and input-clock timing as part of the system-level timing budget, especially when the buffer feeds a counter, latch, or communications transceiver. Confirm all timing, output-enable, and propagation-delay requirements against the manufacturer datasheet before release.

This product page consolidates the confirmed ICS542MIT electrical and packaging details, practical clock-distribution guidance, a strict drop-in cross-reference, and design considerations that help engineers evaluate the device before schematic capture and PCB layout.

Drop-in-Alternativen für ICS542MIT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

542MILFT

✅ Drop-In
📦 8-SOIC, 3.90 mm width
0% stated difference in the cited principal performance characteristics; terminal assignments and package are consistent

📋 Referenzalternative (nicht im Katalog)

ICS542MIT Technische Daten

Device Type Clock fanout buffer and divider
Division Ratio 1:2
Maximum Frequency 156 MHz
Input Logic CMOS
Output Logic 3-state CMOS
Supply Voltage Range 3 V to 5.5 V
Gehäuse 8-SOIC, 3.90 mm width
Montageart Surface mount
Output Count 2 outputs

ICS542MIT 8-soic, 3.90 mm width Pinbelegungsleitfaden

Pinbelegung für ICS542MIT (8-soic, 3.90 mm width-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für ICS542MIT im 8-soic, 3.90 mm width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ICS542MIT.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ICS542MIT ist geeignet für 6 Anwendungs: Communications Clock Distribution, Industrial Control Systems, Test and Measurement Equipment, Digital Logic Fanout, Data Acquisition and Conversion, General-Purpose Digital Platforms.

🌐

Communications Clock Distribution

The ICS542MIT is suitable for communications equipment that must distribute a divided CMOS clock to two receiving circuits. Its 1:2 division ratio provides a defined clock relationship at the outputs, while the 156 MHz maximum input frequency accommodates many legacy and industrial interface clocking schemes. The two three-state CMOS outputs allow clock destinations to be isolated when their receiving logic is inactive or held in a reset state. Because the outputs are divided, downstream serializers, counters, and protocol engines must use the correct reduced frequency when calculating timeouts and setup margins. A short clock distribution area with continuous ground references helps preserve edge quality.

🏭

Industrial Control Systems

Industrial control systems often require one system clock to feed separate processing and peripheral sections. The ICS542MIT accepts a CMOS clock input up to 156 MHz and supplies two three-state CMOS outputs at the divided rate, allowing clock destinations to be controlled independently through output-enable signals. This arrangement is useful when a controller and an external interface need related but non-identical timing. Designers should include the divider ratio in the control-loop timing budget and verify propagation delay against the relevant task period. Short traces, solid ground-plane continuity, and localized supply bypassing are important in control systems where switching equipment may create ground and supply disturbances.

📺

Test and Measurement Equipment

The ICS542MIT can provide a divided and distributed clock for test and measurement equipment that contains several clocked subcircuits. Its two three-state outputs can feed separate acquisition, conversion, or processing stages, while the 1:2 ratio provides a convenient frequency relationship. The 156 MHz maximum operating frequency makes it appropriate for systems whose internal reference clocks remain below that limit. Instrument designs should account for output jitter, propagation delay, and load-dependent behavior against the measurement accuracy budget. Keeping the clock path compact and referencing it to an uninterrupted ground plane helps reduce sensitivity to digital coupling and ground bounce.

🔧

Digital Logic Fanout

The ICS542MIT is useful when a CMOS clock source must drive more than one digital destination without directly loading the source. Its two three-state CMOS outputs isolate the source from downstream loads, and the 1:2 division ratio gives each receiving circuit a defined divided clock. This arrangement can simplify designs that previously required multiple distribution buffers or explicit output gating. The receiving logic must be checked for valid setup and hold margins at the divided frequency, and unused outputs should be controlled rather than left without a defined state. The 8-SOIC package supports conventional surface-mount routing on both new and existing controller boards.

📡

Data Acquisition and Conversion

Data-acquisition systems often distribute a sampling or conversion clock to multiple analog and digital sections. The ICS542MIT provides a divided clock through two independently controllable three-state CMOS outputs, allowing acquisition channels or converter banks to be isolated when not required. Its 156 MHz input ceiling supports common control-clock rates, while the divided output timing must be included in conversion-valid and data-capture windows. Designers should verify the exact propagation and output-enable timing in the manufacturer datasheet, especially where acquisition starts or stops dynamically. Controlled return paths and nearby bypass capacitance help maintain clock and reference integrity in mixed-signal systems.

🖥️

General-Purpose Digital Platforms

The ICS542MIT fits general-purpose digital platforms that require a compact clock-distribution stage for two logic blocks. Its 3 V to 5.5 V operating range supports common digital supply systems, and the 8-SOIC package is straightforward to assemble using standard surface-mount processes. Two three-state outputs provide basic isolation and gating functions, but enable sequencing must be designed around the output-state requirements of each load. Because the device divides the source clock, downstream frequency-sensitive functions should be checked carefully. The principal implementation benefits are fewer interconnections from the clock source, controlled output loading, and a defined divider relationship across the two destinations.

What is the ICS542MIT?
The ICS542MIT is a Renesas Electronics clock fanout buffer and divider with a 1:2 division ratio and a maximum frequency of 156 MHz. According to the Renesas product listing and manufacturer datasheet, it accepts a CMOS clock input and provides two three-state CMOS outputs. The device is packaged in an 8-SOIC package measuring 3.90 mm in width.
What is the operating voltage of ICS542MIT?
The ICS542MIT operates from 3 V to 5.5 V. The Renesas product documentation identifies the supply range as 3 V to 5.5 V, allowing the same clock distribution circuit to support common 3.3 V and 5 V digital environments. Confirm signal-level compatibility and timing margins against the complete manufacturer datasheet.
What clock frequency does ICS542MIT support?
The ICS542MIT supports clock inputs up to 156 MHz. The Renesas product listing identifies 156 MHz as the maximum frequency, making the device suitable for communications, control, instrumentation, and digital logic that operate below that limit. Because it divides the clock, verify the required output frequency at each destination.
What is the division ratio of ICS542MIT?
The ICS542MIT has a 1:2 clock division ratio. Its CMOS input feeds two three-state CMOS outputs according to the Renesas product classification. Designers should use the divided output frequency when setting downstream prescaler, timeout, serialization, or sampling timing.
Where can I download the ICS542MIT datasheet PDF?
The ICS542MIT datasheet is available through the product-documentation link on this page. The Renesas product listing identifies the device as a 156 MHz, 1:2 clock fanout buffer and divider in an 8-SOIC package. Use the manufacturer datasheet for the authoritative pin description, timing diagrams, and electrical characteristics.
Where can I find the ICS542MIT pinout?
The ICS542MIT uses an 8-SOIC package, and its numbered pin assignment is defined in the manufacturer datasheet. Use the pin-description table and package drawing when assigning power, ground, clock input, outputs, and output-enable controls. The ICS542MIT package drawing confirms the eight-lead SOIC outline.
What can replace the ICS542MIT?
The 542MILFT from Microchip Technology is identified as a pin-compatible replacement for the ICS542MIT, with matching terminals and package characteristics. According to the published cross-reference comparison, its main performance parameters and functional characteristics are consistent. Validate timing, enable logic, supply operation, and lifecycle requirements before production substitution.
Is the 542MILFT the same as the ICS542MIT?
The 542MILFT is a cross-manufacturer equivalent identified as pin-compatible with the ICS542MIT. The published comparison states that the terminal assignments and packages are consistent and that the principal performance characteristics match. Despite that equivalence, confirm each device's output-enable polarity and full timing tables before treating them as interchangeable.
ICS542MIT vs 542MILFT - which is better for clock distribution?
The ICS542MIT and 542MILFT are both suitable for pin-compatible clock-distribution designs, with the 542MILFT identified as a direct replacement candidate. Choose based on confirmed lifecycle, regional sourcing, and device-specific timing requirements rather than assuming every electrical characteristic is identical. The 542MILFT provides an alternative source when its current status and qualifications satisfy the application.
When should I choose ICS542MIT over the 542MILFT?
Choose the ICS542MIT when it is the preferred maintained part for the specific suffix, package, qualification, and regional supply requirements of the design. Choose the 542MILFT when it offers an acceptable supply-chain advantage and its datasheet confirms equivalent timing and enable behavior. Both use the same stated package class for the cited replacement.
Is ICS542MIT suitable for digital control and communications systems?
The ICS542MIT is suitable for digital control and communications systems requiring a divided CMOS clock distributed to two destinations. Its 156 MHz maximum frequency, 3 V to 5.5 V supply range, and three-state CMOS outputs support common digital clocking architectures. The divided output must be included in the timing budget of every receiving circuit.
What design considerations apply to ICS542MIT clock routing?
Keep ICS542MIT clock traces short, provide a continuous ground reference, and place the required bypass capacitor close to the supply pins. Account for input-to-output propagation delay when designing feedback or cascaded clock paths. Use the manufacturer timing diagrams to verify output-enable setup and hold requirements.
How much power does the ICS542MIT consume?
The ICS542MIT supply-current and power-consumption figures must be taken from the manufacturer datasheet for the selected voltage and output-state conditions. Its confirmed operating supply range is 3 V to 5.5 V. Calculate worst-case dissipation with both outputs enabled and terminated for the actual board configuration before release.
Where can I buy the ICS542MIT?
Use the Request a Quote form on this page to request the current ICS542MIT quotation, availability, and lead time. Current commercial terms can change, so request them for the exact MPN ICS542MIT and the required SOIC package and quantity. The request should also specify the production quantity and delivery schedule.
What is the price of the ICS542MIT?
The current ICS542MIT price is shown through the Request a Quote form on this page after the required part, quantity, and delivery details are entered. Pricing depends on quantity, package configuration, current supply, and commercial terms. Submit an RFQ for the exact ICS542MIT MPN rather than relying on an outdated market summary.
What is the lead time and stock status for ICS542MIT?
Request the current lead time and stock status through the Request a Quote form on this page. Availability can vary with order quantity, suffix, region, and production schedule, so the RFQ response should be treated as the commercial commitment. Provide the required delivery date and annual usage with the request.

Technische Referenzdaten für ICS542MIT – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ICS542MIT when it is the preferred part for the exact suffix, qualification, lifecycle, and regional sourcing requirements of the design. Its confirmed 1:2 division ratio, 156 MHz maximum frequency, two three-state CMOS outputs, and 3 V to 5.5 V supply range make it suitable for clock distribution in communications, industrial control, test equipment, and digital systems. The 542MILFT is the relevant drop-in candidate when it offers a sourcing advantage and its manufacturer datasheet confirms equivalent pin behavior, timing, and output-enable polarity. Because the cited comparison describes matching terminals and principal characteristics, neither part should be selected solely on nominal frequency and package; lifecycle, qualifications, and device-specific timing data determine the better production choice.

Vergleich mit Alternativen

Parameter Dieses Produkt 542MILFT
Manufacturer Renesas Electronics Microchip Technology
Package 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width
Device Type Clock fanout buffer and divider Clock fanout buffer and divider
Division Ratio 1:2 1:2
Maximum Frequency 156 MHz 156 MHz
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V
Output Logic 3-state CMOS 3-state CMOS
Pin Compatibility 8-SOIC reference footprint Terminals and package consistent with ICS542MIT

Wichtigste Unterscheidungsmerkmale

  • Combined clock division and two-output distribution (vs. 542MILFT)
  • Confirmed 156 MHz operating class (vs. 542MILFT)
  • Drop-in package continuity (vs. 542MILFT)

Designhinweise

Route the input clock and both outputs as short, direct paths on a continuous ground reference. Avoid crossing clock traces over noisy power-switching nodes or splitting the ground reference beneath the routes. Place any required bypass capacitor close to the supply pins, and minimize stubs because additional trace capacitance can affect clock edge rate and output timing.

Include the 1:2 division ratio in the timing budget for every receiving circuit. Confirm propagation delay, output rise and fall times, and output-enable setup and hold requirements in the manufacturer datasheet. If the outputs drive longer cables or higher capacitance than the reference circuit, re-evaluate edge degradation and termination rather than assuming the 156 MHz rating alone guarantees acceptable behavior.

Do not treat the three-state outputs as automatically safe to leave floating. Define the state of every output during reset, power sequencing, and unused intervals, and ensure output-enable polarity matches the receiving logic. Also verify that downstream devices tolerate the divided clock frequency; replacing the source with a different frequency can change divider alignment even when the nominal input limit remains unchanged.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available product information does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is not applicable because the device is an industrial/commercial clock and timing IC, not an automotive-qualified product.

Daten verifiziert am: 2026-11-11 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

ICS542MIT datasheet ICS542MIT specifications ICS542MIT pinout ICS542MIT datasheet pdf ICS542MIT equivalent ICS542MIT replacement ICS542MIT vs 542MILFT ICS542MIT 156 MHz ICS542MIT 1:2 divider Renesas ICS542MIT ICS542MIT 8-SOIC ICS542MIT clock buffer application ICS542MIT price ICS542MIT stock

Verwandte Bauteile & Begriffe

Renesas Electronics ICS542MIT 542MILFT Microchip Technology clock fanout buffer clock divider clock distribution clock and timing IC CMOS input three-state CMOS output 1:2 division ratio 156 MHz 3 V to 5.5 V supply 8-SOIC SOIC package family surface mount SMD propagation delay output-enable clock routing signal integrity communications equipment industrial control systems test and measurement
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen