ICS542MIT - 1:2 156 MHz Clock Fanout Buffer | Renesas
MPN: ICS542MIT ✓ सक्रियICS542MIT अवलोकन
A clock fanout buffer is a clock and timing IC that reproduces or distributes a clock signal while controlling impedance, loading, and signal timing. The ICS542MIT belongs to the broader clock buffer and driver hierarchy, where clock distribution devices isolate a source from downstream capacitance and provide predictable edge propagation into logic circuits. Its 3 V to 5.5 V supply range allows operation across common low-voltage digital systems.
The device combines a 1:2 divider function with clock fanout capability. Its three-state CMOS outputs can place individual outputs into a high-impedance state when the receiving circuitry does not need a clock, while the 156 MHz maximum frequency supports common communications, control, and digital-logic clock domains. The 8-SOIC package is suitable for conventional surface-mount PCB assembly and offers a practical upgrade path for designs requiring more than a direct clock connection.
Clock distribution requires careful attention to edge rate, output loading, return path continuity, and trace length. The three-state outputs make output-enable control relevant to system power management and bus segmentation. Because the ICS542MIT divides the input clock, downstream logic should be evaluated against the divided output frequency rather than assuming the source frequency appears unchanged at the receiver.
Typical applications include communication equipment, control systems, test and measurement products, and general-purpose digital platforms that require one input clock to feed two destinations. The device is particularly useful where one subsystem needs a divided clock or where multiple clock domains must receive independently controlled outputs. Its 156 MHz ceiling also makes it applicable to systems operating below that frequency without requiring a higher-speed clock distribution architecture.
When laying out the circuit, keep clock traces short, provide a continuous ground reference, and place decoupling close to the supply pins. Treat output-enable and input-clock timing as part of the system-level timing budget, especially when the buffer feeds a counter, latch, or communications transceiver. Confirm all timing, output-enable, and propagation-delay requirements against the manufacturer datasheet before release.
This product page consolidates the confirmed ICS542MIT electrical and packaging details, practical clock-distribution guidance, a strict drop-in cross-reference, and design considerations that help engineers evaluate the device before schematic capture and PCB layout.
के लिए ड्रॉप-इन विकल्प ICS542MIT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
542MILFT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS542MIT विशेषताएं
| Device Type | Clock fanout buffer and divider |
| Division Ratio | 1:2 |
| Maximum Frequency | 156 MHz |
| Input Logic | CMOS |
| Output Logic | 3-state CMOS |
| Supply Voltage Range | 3 V to 5.5 V |
| पैकेज | 8-SOIC, 3.90 mm width |
| माउंटिंग प्रकार | Surface mount |
| Output Count | 2 outputs |
ICS542MIT 8-soic, 3.90 mm width पिन कॉन्फ़िगरेशन गाइड
ICS542MIT (8-soic, 3.90 mm width पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ICS542MIT.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ICS542MIT के लिए उपयुक्त है 6 अनुप्रयोगs: Communications Clock Distribution, Industrial Control Systems, Test and Measurement Equipment, Digital Logic Fanout, Data Acquisition and Conversion, General-Purpose Digital Platforms.
Communications Clock Distribution
The ICS542MIT is suitable for communications equipment that must distribute a divided CMOS clock to two receiving circuits. Its 1:2 division ratio provides a defined clock relationship at the outputs, while the 156 MHz maximum input frequency accommodates many legacy and industrial interface clocking schemes. The two three-state CMOS outputs allow clock destinations to be isolated when their receiving logic is inactive or held in a reset state. Because the outputs are divided, downstream serializers, counters, and protocol engines must use the correct reduced frequency when calculating timeouts and setup margins. A short clock distribution area with continuous ground references helps preserve edge quality.
Industrial Control Systems
Industrial control systems often require one system clock to feed separate processing and peripheral sections. The ICS542MIT accepts a CMOS clock input up to 156 MHz and supplies two three-state CMOS outputs at the divided rate, allowing clock destinations to be controlled independently through output-enable signals. This arrangement is useful when a controller and an external interface need related but non-identical timing. Designers should include the divider ratio in the control-loop timing budget and verify propagation delay against the relevant task period. Short traces, solid ground-plane continuity, and localized supply bypassing are important in control systems where switching equipment may create ground and supply disturbances.
Test and Measurement Equipment
The ICS542MIT can provide a divided and distributed clock for test and measurement equipment that contains several clocked subcircuits. Its two three-state outputs can feed separate acquisition, conversion, or processing stages, while the 1:2 ratio provides a convenient frequency relationship. The 156 MHz maximum operating frequency makes it appropriate for systems whose internal reference clocks remain below that limit. Instrument designs should account for output jitter, propagation delay, and load-dependent behavior against the measurement accuracy budget. Keeping the clock path compact and referencing it to an uninterrupted ground plane helps reduce sensitivity to digital coupling and ground bounce.
Digital Logic Fanout
The ICS542MIT is useful when a CMOS clock source must drive more than one digital destination without directly loading the source. Its two three-state CMOS outputs isolate the source from downstream loads, and the 1:2 division ratio gives each receiving circuit a defined divided clock. This arrangement can simplify designs that previously required multiple distribution buffers or explicit output gating. The receiving logic must be checked for valid setup and hold margins at the divided frequency, and unused outputs should be controlled rather than left without a defined state. The 8-SOIC package supports conventional surface-mount routing on both new and existing controller boards.
Data Acquisition and Conversion
Data-acquisition systems often distribute a sampling or conversion clock to multiple analog and digital sections. The ICS542MIT provides a divided clock through two independently controllable three-state CMOS outputs, allowing acquisition channels or converter banks to be isolated when not required. Its 156 MHz input ceiling supports common control-clock rates, while the divided output timing must be included in conversion-valid and data-capture windows. Designers should verify the exact propagation and output-enable timing in the manufacturer datasheet, especially where acquisition starts or stops dynamically. Controlled return paths and nearby bypass capacitance help maintain clock and reference integrity in mixed-signal systems.
General-Purpose Digital Platforms
The ICS542MIT fits general-purpose digital platforms that require a compact clock-distribution stage for two logic blocks. Its 3 V to 5.5 V operating range supports common digital supply systems, and the 8-SOIC package is straightforward to assemble using standard surface-mount processes. Two three-state outputs provide basic isolation and gating functions, but enable sequencing must be designed around the output-state requirements of each load. Because the device divides the source clock, downstream frequency-sensitive functions should be checked carefully. The principal implementation benefits are fewer interconnections from the clock source, controlled output loading, and a defined divider relationship across the two destinations.
के लिए इंजीनियरिंग संदर्भ डेटा ICS542MIT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | 542MILFT |
|---|---|---|
| Manufacturer | Renesas Electronics | Microchip Technology |
| Package | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width |
| Device Type | Clock fanout buffer and divider | Clock fanout buffer and divider |
| Division Ratio | 1:2 | 1:2 |
| Maximum Frequency | 156 MHz | 156 MHz |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Output Logic | 3-state CMOS | 3-state CMOS |
| Pin Compatibility | 8-SOIC reference footprint | Terminals and package consistent with ICS542MIT |
मुख्य विशेषताएँ
- Combined clock division and two-output distribution (बनाम542MILFT)
- Confirmed 156 MHz operating class (बनाम542MILFT)
- Drop-in package continuity (बनाम542MILFT)
डिज़ाइन नोट्स
Route the input clock and both outputs as short, direct paths on a continuous ground reference. Avoid crossing clock traces over noisy power-switching nodes or splitting the ground reference beneath the routes. Place any required bypass capacitor close to the supply pins, and minimize stubs because additional trace capacitance can affect clock edge rate and output timing.
Include the 1:2 division ratio in the timing budget for every receiving circuit. Confirm propagation delay, output rise and fall times, and output-enable setup and hold requirements in the manufacturer datasheet. If the outputs drive longer cables or higher capacitance than the reference circuit, re-evaluate edge degradation and termination rather than assuming the 156 MHz rating alone guarantees acceptable behavior.
Do not treat the three-state outputs as automatically safe to leave floating. Define the state of every output during reset, power sequencing, and unused intervals, and ensure output-enable polarity matches the receiving logic. Also verify that downstream devices tolerate the divided clock frequency; replacing the source with a different frequency can change divider alignment even when the nominal input limit remains unchanged.
अनुपालन जानकारी
The available product information does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is not applicable because the device is an industrial/commercial clock and timing IC, not an automotive-qualified product.