ICS558G-01 - 250 MHz 2:4 CMOS Clock Buffer | Renesas
Teilenummer: ICS558G-01 ✓ AktivICS558G-01 Übersicht
A clock fanout buffer, also called a clock distribution buffer, is a clock and timing IC that receives one clock signal and reproduces it across multiple outputs. It belongs to the clock buffer and driver family within the broader clock and timing IC category. Clock buffers isolate the source from downstream loading, provide multiple usable clock destinations, and can reduce the timing disturbance that would otherwise appear when several circuits were connected directly to one clock source.
The ICS558G-01 provides four CMOS outputs with three-state capability, allowing one, three, or all four outputs to be disabled independently through the output-enable controls. Its input stage supports CMOS and PECL signaling, giving it utility in systems that translate or distribute clocks between different logic families. The 250 MHz maximum operating frequency places it in applications such as telecommunications, networking equipment, industrial control, and general-purpose digital logic.
Renesas describes the ICS558-01 as a TO CMOS clock driver with an integrated divide-by-4 function and four low-skew outputs. The divide capability allows the device to support clock distribution arrangements where a divided reference is needed in addition to distributed outputs. The configurable output-enable inputs add bus-management flexibility, particularly in test systems and backplane systems where clock outputs must be parked while a channel is inactive.
Typical uses include switching and routing fabrics in telecommunications equipment, parallel clock distribution in network interfaces, synchronization in industrial controllers, and clock generation stages in test and measurement instruments. The device is also suitable for backplane applications because its three-state outputs can be disabled when a module is not selected, reducing contention and unwanted clock activity.
The principal design consideration is signal integrity. Because the ICS558G-01 is intended for high-speed distribution, trace length matching, controlled impedance routing, and short output stub lengths help preserve edge quality and maintain usable skew. Decoupling should be placed close to the supply pins, and unused outputs should be disabled rather than left permanently enabled if downstream channels are not required.
This page combines the principal electrical specifications, interface details, application guidance, design notes, and verified sourcing information for the ICS558G-01. It also provides a framework for evaluating compatible replacements without changing the 16-TSSOP board footprint or the 2:4 clock-distribution function.
Drop-in-Alternativen für ICS558G-01 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
ICS558G-01T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
558G-01LFT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ICS558G-01 Technische Daten
| Device Type | Clock fanout buffer, divider, and multiplexer |
| Fanout Ratio | 2:4 |
| Maximum Frequency | 250 MHz |
| Input Signal Type | CMOS or PECL |
| Output Signal Type | 3-state CMOS |
| Supply Voltage Range | 2.375 V to 5.5 V |
| Anzahl der Ausgänge | 4 |
| Output Enable Control | Individual three-state output enables |
| Integrated Divider | Divide-by-4 |
| Number of Circuits | 1 |
| Gehäuse | 16-TSSOP |
| Package Width | 0.173 inch (4.40 mm) |
| Montageart | Surface mount |
| Logic Family | CMOS / PECL input, CMOS output |
ICS558G-01 0.173 inch (4.40 mm) Pinbelegungsleitfaden
Pinbelegung für ICS558G-01 (0.173 inch (4.40 mm)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ICS558G-01.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ICS558G-01 ist geeignet für 6 Anwendungs: Telecommunications Backplane Clock Distribution, Network Interface Clock Fanout, Industrial Control and Synchronization, Test and Measurement Clock Trees, Data Converter and Processor Clocking, Mixed PECL and CMOS Clock Translation.
Telecommunications Backplane Clock Distribution
The ICS558G-01 fits telecommunications backplane designs that must deliver one reference clock to several line cards while parking unused destinations. Its 2:4 fanout provides four CMOS clock outputs, while the three-state controls allow a disabled output to be held in a high-impedance state when a module is inactive. The 250 MHz maximum frequency supports high-speed backplane logic, and the 2.375 V to 5.5 V supply range covers low- and nominal-voltage rails. The principal engineering trade-off is that a long backplane trace can accumulate skew and reflections, so route each destination with controlled impedance and verify edge quality at the far end under representative loading.
Empfohlen
Network Interface Clock Fanout
The ICS558G-01 can distribute a high-speed reference into network interface sections that require separate clock destinations for serialization, framing, and control logic. Its CMOS or PECL input capability allows the source clock to remain in the logic family already used by the system, while the four CMOS outputs provide local, low-skew copies. This arrangement can reduce the load presented to the oscillator or transceiver by isolating downstream branches behind the buffer. Because the device operates up to 250 MHz, trace geometry becomes critical: use short branches, avoid unnecessary vias, and maintain consistent return paths so reflections do not degrade the clock edge.
Empfohlen
Industrial Control and Synchronization
The ICS558G-01 is useful in industrial controllers where multiple subsystems must operate from a common timing reference. The integrated divide-by-4 function can support a lower-rate destination alongside the distributed clock, while the 250 MHz capability leaves performance margin for faster control or communications blocks. The three-state outputs let firmware isolate a branch during a controlled transition instead of leaving an unloaded destination permanently active. For industrial equipment, pay particular attention to supply-noise isolation, bypass-capacitor placement, and ground continuity, since clock edges must remain predictable even when adjacent power stages are switching.
Empfohlen
Test and Measurement Clock Trees
The ICS558G-01 can fan out a reference clock inside test and measurement instruments that feed acquisition, processing, and conversion sections. Four independently enabled CMOS outputs allow unused destinations to be tri-stated, reducing unwanted activity and helping isolate a channel under test. Its divider capability offers an additional divided clock relationship that can support slower instrumentation blocks. The key performance consideration is edge quality rather than only nominal frequency, so characterize the source impedance, output loading, cable or trace topology, and receiver thresholds before relying on 250 MHz operation across the complete instrument.
Empfohlen
Data Converter and Processor Clocking
The ICS558G-01 can provide local clock copies to processors, data converters, and interface blocks that need a common but physically separated timing source. The input divider provides flexibility in generating related clock domains, while the four outputs can feed several destinations without connecting each load directly to the source. At 250 MHz, the buffer supports demanding digital systems, but the benefit depends on sound board implementation. Keep output traces short, match them where required, and provide a continuous reference plane so that the low-skew output specification is preserved rather than degraded by board discontinuities.
Empfohlen
Mixed PECL and CMOS Clock Translation
The ICS558G-01 is suited to systems in which an upstream clock source uses PECL and downstream destinations require CMOS. Its input stage accepts either CMOS or PECL, and the four outputs are CMOS, allowing the device to serve as the distribution and level-conversion stage in one package. This can simplify board partitioning compared with a separate level translator followed by a fanout buffer. The trade-off is that the actual logic levels and timing margins depend on supply voltage and input configuration, so reference-voltage and termination values must be confirmed in the manufacturer electrical tables before layout release.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ICS558G-01 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ICS558G-01T | 558G-01LFT |
|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Renesas Electronics | Renesas Electronics | Integrated Device Technology |
| Device Type | Clock fanout buffer, divider, and multiplexer | Clock fanout buffer, divider, and multiplexer | 2:4 clock buffer |
| Fanout Ratio | 2:4 | 2:4 | 2:4 |
| Output Type | Three-state CMOS | Three-state CMOS | CMOS |
| Number of Outputs | 4 | 4 | 4 |
Wichtigste Unterscheidungsmerkmale
- Mixed PECL or CMOS input with four three-state CMOS outputs (vs. ICS558G-01T)
- Integrated divide-by-4 function (vs. 558G-01LFT)
- Wide single-supply operating range (vs. 558G-01LFT)
Designhinweise
Route all four clock outputs as controlled-impedance transmission lines and keep branches as short as practical. Match output-to-output trace lengths where the receiving devices require closely aligned edges. Avoid long stubs and abrupt layer changes because both can create reflections that degrade the clock edge even though the device itself has a 250 MHz maximum operating frequency.
Place the recommended bypass capacitance immediately across the supply pins and provide a low-inductance connection to the ground reference. Keep the clock-buffer region away from switching nodes and high-current return paths. A continuous reference plane beneath the clock traces is preferable to a fragmented plane, since discontinuities increase loop area and can couple noise into the distributed clock.
Do not assume that every similarly described 2:4 clock buffer is interchangeable. Compare the pin names, output-enable polarity, divider configuration, input reference requirements, supply limits, and maximum frequency before releasing a substitute to production. The ICS558G-01T packaging code is the closest ordering option, while other ordering codes require a full manufacturer specification review.
Compliance-Informationen
The verified manufacturer and distributor listings identify the device, electrical function, package, and supply range but do not provide explicit environmental-compliance declarations.