Renesas Electronics

ICS558G-01 - 250 MHz 2:4 CMOS Clock Buffer | Renesas

MPN: ICS558G-01 ✓ فعال
2.375 V to 5.5 V Vdss 16-TSSOP Package 250 MHz Speed
MOQ: 1 |

ICS558G-01 جائزہ

The Renesas ICS558G-01 is a 2:4 fanout clock buffer that distributes a high-speed clock to four low-skew CMOS outputs. The device accepts either CMOS or PECL input, operates from a 2.375 V to 5.5 V supply, and supports frequencies up to 250 MHz. It is packaged in a 16-pin TSSOP measuring 0.173 inch, or 4.40 mm, in width.

A clock fanout buffer, also called a clock distribution buffer, is a clock and timing IC that receives one clock signal and reproduces it across multiple outputs. It belongs to the clock buffer and driver family within the broader clock and timing IC category. Clock buffers isolate the source from downstream loading, provide multiple usable clock destinations, and can reduce the timing disturbance that would otherwise appear when several circuits were connected directly to one clock source.

The ICS558G-01 provides four CMOS outputs with three-state capability, allowing one, three, or all four outputs to be disabled independently through the output-enable controls. Its input stage supports CMOS and PECL signaling, giving it utility in systems that translate or distribute clocks between different logic families. The 250 MHz maximum operating frequency places it in applications such as telecommunications, networking equipment, industrial control, and general-purpose digital logic.

Renesas describes the ICS558-01 as a TO CMOS clock driver with an integrated divide-by-4 function and four low-skew outputs. The divide capability allows the device to support clock distribution arrangements where a divided reference is needed in addition to distributed outputs. The configurable output-enable inputs add bus-management flexibility, particularly in test systems and backplane systems where clock outputs must be parked while a channel is inactive.

Typical uses include switching and routing fabrics in telecommunications equipment, parallel clock distribution in network interfaces, synchronization in industrial controllers, and clock generation stages in test and measurement instruments. The device is also suitable for backplane applications because its three-state outputs can be disabled when a module is not selected, reducing contention and unwanted clock activity.

The principal design consideration is signal integrity. Because the ICS558G-01 is intended for high-speed distribution, trace length matching, controlled impedance routing, and short output stub lengths help preserve edge quality and maintain usable skew. Decoupling should be placed close to the supply pins, and unused outputs should be disabled rather than left permanently enabled if downstream channels are not required.

This page combines the principal electrical specifications, interface details, application guidance, design notes, and verified sourcing information for the ICS558G-01. It also provides a framework for evaluating compatible replacements without changing the 16-TSSOP board footprint or the 2:4 clock-distribution function.

کے لیے ڈراپ اِن متبادل ICS558G-01 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

ICS558G-01T

✅ ڈراپ-اِن
📦 16-TSSOP
Same 2:4 function, 250 MHz maximum frequency, and 16-TSSOP footprint; ordering code differs by tape-and-reel packaging

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

558G-01LFT

✅ ڈراپ-اِن
📦 16-TSSOP
Same 2:4 clock-buffer function and package characteristics; ordering code and associated grade terms differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ICS558G-01 تفصیلات

Device Type Clock fanout buffer, divider, and multiplexer
Fanout Ratio 2:4
Maximum Frequency 250 MHz
Input Signal Type CMOS or PECL
Output Signal Type 3-state CMOS
Supply Voltage Range 2.375 V to 5.5 V
آؤٹ پٹس کی تعداد 4
Output Enable Control Individual three-state output enables
Integrated Divider Divide-by-4
Number of Circuits 1
پیکیج 16-TSSOP
Package Width 0.173 inch (4.40 mm)
ماؤنٹنگ ٹائپ Surface mount
Logic Family CMOS / PECL input, CMOS output

ICS558G-01 0.173 inch (4.40 mm) پن کنفیگریشن گائیڈ

ICS558G-01 (0.173 inch (4.40 mm) پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

ICS558G-01 کے لیے 0.173 inch (4.40 mm) پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ICS558G-01.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

ICS558G-01 کے لیے موزوں ہے 6 ایپلیکیشنs: Telecommunications Backplane Clock Distribution, Network Interface Clock Fanout, Industrial Control and Synchronization, Test and Measurement Clock Trees, Data Converter and Processor Clocking, Mixed PECL and CMOS Clock Translation.

🌐

Telecommunications Backplane Clock Distribution

The ICS558G-01 fits telecommunications backplane designs that must deliver one reference clock to several line cards while parking unused destinations. Its 2:4 fanout provides four CMOS clock outputs, while the three-state controls allow a disabled output to be held in a high-impedance state when a module is inactive. The 250 MHz maximum frequency supports high-speed backplane logic, and the 2.375 V to 5.5 V supply range covers low- and nominal-voltage rails. The principal engineering trade-off is that a long backplane trace can accumulate skew and reflections, so route each destination with controlled impedance and verify edge quality at the far end under representative loading.

🖥️

Network Interface Clock Fanout

The ICS558G-01 can distribute a high-speed reference into network interface sections that require separate clock destinations for serialization, framing, and control logic. Its CMOS or PECL input capability allows the source clock to remain in the logic family already used by the system, while the four CMOS outputs provide local, low-skew copies. This arrangement can reduce the load presented to the oscillator or transceiver by isolating downstream branches behind the buffer. Because the device operates up to 250 MHz, trace geometry becomes critical: use short branches, avoid unnecessary vias, and maintain consistent return paths so reflections do not degrade the clock edge.

🏭

Industrial Control and Synchronization

The ICS558G-01 is useful in industrial controllers where multiple subsystems must operate from a common timing reference. The integrated divide-by-4 function can support a lower-rate destination alongside the distributed clock, while the 250 MHz capability leaves performance margin for faster control or communications blocks. The three-state outputs let firmware isolate a branch during a controlled transition instead of leaving an unloaded destination permanently active. For industrial equipment, pay particular attention to supply-noise isolation, bypass-capacitor placement, and ground continuity, since clock edges must remain predictable even when adjacent power stages are switching.

🔧

Test and Measurement Clock Trees

The ICS558G-01 can fan out a reference clock inside test and measurement instruments that feed acquisition, processing, and conversion sections. Four independently enabled CMOS outputs allow unused destinations to be tri-stated, reducing unwanted activity and helping isolate a channel under test. Its divider capability offers an additional divided clock relationship that can support slower instrumentation blocks. The key performance consideration is edge quality rather than only nominal frequency, so characterize the source impedance, output loading, cable or trace topology, and receiver thresholds before relying on 250 MHz operation across the complete instrument.

💡

Data Converter and Processor Clocking

The ICS558G-01 can provide local clock copies to processors, data converters, and interface blocks that need a common but physically separated timing source. The input divider provides flexibility in generating related clock domains, while the four outputs can feed several destinations without connecting each load directly to the source. At 250 MHz, the buffer supports demanding digital systems, but the benefit depends on sound board implementation. Keep output traces short, match them where required, and provide a continuous reference plane so that the low-skew output specification is preserved rather than degraded by board discontinuities.

📡

Mixed PECL and CMOS Clock Translation

The ICS558G-01 is suited to systems in which an upstream clock source uses PECL and downstream destinations require CMOS. Its input stage accepts either CMOS or PECL, and the four outputs are CMOS, allowing the device to serve as the distribution and level-conversion stage in one package. This can simplify board partitioning compared with a separate level translator followed by a fanout buffer. The trade-off is that the actual logic levels and timing margins depend on supply voltage and input configuration, so reference-voltage and termination values must be confirmed in the manufacturer electrical tables before layout release.

تجویز کردہ پروڈکٹس کا خلاصہ

ICS558G-01T Tape-and-reel ordering configuration of the same clock-buffer device استعمال ہوتا ہے: Telecommunications Backplane Clock Distribution, Network Interface Clock Fanout, Industrial Control and Synchronization, Test and Measurement Clock Trees, Data Converter and Processor Clocking, Mixed PECL and CMOS Clock Translation
What is the ICS558G-01 clock buffer used for?
The ICS558G-01 is used to distribute one high-speed input clock across four low-skew CMOS outputs. Renesas describes the device as a TO CMOS clock driver with selectable three-state output enables, allowing one, three, or all four outputs to be disabled. The 250 MHz maximum operating frequency makes it appropriate for telecommunications, networking, industrial control, and test-equipment clock trees.
What is the maximum operating frequency of the ICS558G-01?
The ICS558G-01 operates at frequencies up to 250 MHz. DigiKey classifies the component as a 2:4 clock fanout buffer with a maximum frequency of 250 MHz, while the manufacturer datasheet identifies it as a high-speed TO CMOS clock driver. Actual usable frequency depends on supply voltage, output loading, trace impedance, and the clock-edge requirements of the receiving circuitry.
What input and output logic levels does the ICS558G-01 support?
The ICS558G-01 accepts CMOS or PECL clock inputs and drives three-state CMOS outputs. According to the Renesas ICS558-01 datasheet, the input stage supports either CMOS or PECL while the output stage provides four CMOS signals. Designers should still confirm input termination, reference voltage, and output-drive requirements against the detailed electrical tables before finalizing a board design.
What is the supply voltage range of the ICS558G-01?
The ICS558G-01 operates from 2.375 V to 5.5 V. The 2.375 V minimum supports low-voltage systems, while the 5.5 V maximum permits 5 V operation within the specified supply range. Place the recommended bypass capacitance close to the supply pins and route it through a short, low-inductance path to limit supply noise on the clock outputs.
How many outputs can the ICS558G-01 disable?
The ICS558G-01 can tri-state one, three, or all four of its CMOS outputs through its output-enable controls. This flexibility is useful in backplanes and modular systems where a disabled clock should not drive a disconnected or parked module. The exact output-enable logic and active polarity should be verified in the pin-description table of the manufacturer datasheet.
Where can I download the ICS558G-01 datasheet PDF?
The ICS558G-01 datasheet PDF is available from the Renesas-hosted copy linked on this page. It covers the input stage, divide-by-4 function, four low-skew CMOS outputs, three-state controls, and electrical characteristics. Use the pin-description and recommended-layout sections when assigning package pins and laying out the high-speed clock network.
What is the ICS558G-01 package and pin count?
The ICS558G-01 is packaged in a 16-TSSOP with a body width of 0.173 inch, or 4.40 mm. The package is identified as a 16-pin thin shrink small-outline package and is intended for surface-mount assembly. Confirm the exact land pattern and pin orientation against the package drawing in the manufacturer datasheet before layout release.
Can ICS558G-01T replace ICS558G-01 on an existing PCB?
The ICS558G-01T is the orderable tape-and-reel configuration associated with the ICS558G-01, and both are listed as 2:4, 250 MHz clock buffers in 16-TSSOP packages. It is therefore a packaging match for production orders that use the same board footprint. Verify the ordering code, temperature grade, and reel configuration against your purchasing requirements before substitution.
What is the best drop-in replacement for the ICS558G-01?
The closest documented drop-in option is ICS558G-01T, which retains the 2:4 fanout function, 250 MHz maximum frequency, and 16-TSSOP package. The verified cross-reference results did not identify additional pin-compatible parts, so board-layout changes or different-interface devices should not be treated as drop-in replacements. Always compare pinout, voltage range, divider configuration, and output-enable behavior before substitution.
Is the ICS558G-01 the same as the 558G-01LFT?
The 558G-01LFT is described as having the same principal clock-buffer function, terminals, and package characteristics as the ICS558G-01, but it is a different ordering code. Whether it is acceptable for a specific design depends on grade, temperature, and purchasing requirements rather than function alone. Review the manufacturer ordering information and compare the full electrical specifications before treating it as an equivalent.
When should I choose the ICS558G-01 instead of a plain clock buffer?
Choose the ICS558G-01 when the design needs more than a passive fanout: it accepts CMOS or PECL input, includes a divide-by-4 function, and provides four independently tri-statable CMOS outputs. A basic buffer may be sufficient for a single CMOS source with no source termination or output parking, while the ICS558G-01 offers more control for mixed-interface and multi-destination clock trees.
Is the ICS558G-01 suitable for networking and telecommunications equipment?
The ICS558G-01 is suitable for networking and telecommunications clock-distribution stages because it supports frequencies up to 250 MHz, CMOS or PECL inputs, and three-state outputs for module control. Its four-output architecture suits equipment with multiple processing or interface destinations. Signal-integrity verification under actual loading is still required because trace length, impedance, and clock topology determine edge quality.
Where can I buy the ICS558G-01 and what is the current price?
Use the Request a Quote form on this page to request current pricing, stock confirmation, minimum order quantity, and lead time for the ICS558G-01. Commercial terms can change with market conditions and quantity, so they are best confirmed for the exact ordering configuration. The manufacturer and distributor search results on this page identify the part but do not publish a complete quantity-break table for extraction.
What are the key specifications of the ICS558G-01 that engineers should know?
The key specifications are a 2:4 fanout ratio, 250 MHz maximum frequency, CMOS or PECL input, four three-state CMOS outputs, a 2.375 V to 5.5 V supply range, and a 16-TSSOP package. The manufacturer also identifies an integrated divide-by-4 function. These parameters establish the interface, timing, and board-layout constraints for a new clock-distribution design.
How should the ICS558G-01 outputs be routed on a PCB?
Route clock outputs as short, controlled-impedance traces with matched lengths where downstream devices require synchronous arrival. Avoid long stubs, abrupt impedance discontinuities, and proximity to switching nodes because these effects can distort edges and increase skew. Use the recommended decoupling arrangement from the manufacturer datasheet and verify the final clock waveform with an oscilloscope at each destination.
How do I request a lead time and stock check for the ICS558G-01?
Request a current lead time and stock confirmation through the Request a Quote form on this page. Include the required quantity, the ICS558G-01 ordering configuration, and your target delivery date so the request can be evaluated accurately. Lifecycle and availability should always be reconfirmed at the time of purchase rather than inferred from an old distributor listing.

کے لیے انجینئرنگ ریفرنس ڈیٹا ICS558G-01 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Select the ICS558G-01 when the design requires a 250 MHz clock source to feed up to four CMOS destinations with individual three-state control, mixed CMOS or PECL input compatibility, and an integrated divide-by-4 function. It is a strong fit for backplanes, network interfaces, industrial controllers, and test equipment where unused clock branches must be parked rather than left active. ICS558G-01T is the practical alternative when the same electrical device is required in a tape-and-reel production format. Consider 558G-01LFT only after confirming its ordering code, temperature grade, electrical limits, and pin-level behavior. A simple fanout IC is preferable when only passive distribution is needed, while a PLL-based clock generator is preferable when the source requires multiplication, jitter programming, or additional synthesis. In every case, verify the complete output timing and edge quality on the intended PCB.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ ICS558G-01T 558G-01LFT
Package 16-TSSOP 16-TSSOP 16-TSSOP
Brand Renesas Electronics Renesas Electronics Integrated Device Technology
Device Type Clock fanout buffer, divider, and multiplexer Clock fanout buffer, divider, and multiplexer 2:4 clock buffer
Fanout Ratio 2:4 2:4 2:4
Output Type Three-state CMOS Three-state CMOS CMOS
Number of Outputs 4 4 4

اہم امتیازی خصوصیات

  • Mixed PECL or CMOS input with four three-state CMOS outputs (بمقابلہICS558G-01T)
  • Integrated divide-by-4 function (بمقابلہ558G-01LFT)
  • Wide single-supply operating range (بمقابلہ558G-01LFT)

ڈیزائن نوٹس

Route all four clock outputs as controlled-impedance transmission lines and keep branches as short as practical. Match output-to-output trace lengths where the receiving devices require closely aligned edges. Avoid long stubs and abrupt layer changes because both can create reflections that degrade the clock edge even though the device itself has a 250 MHz maximum operating frequency.

Place the recommended bypass capacitance immediately across the supply pins and provide a low-inductance connection to the ground reference. Keep the clock-buffer region away from switching nodes and high-current return paths. A continuous reference plane beneath the clock traces is preferable to a fragmented plane, since discontinuities increase loop area and can couple noise into the distributed clock.

Do not assume that every similarly described 2:4 clock buffer is interchangeable. Compare the pin names, output-enable polarity, divider configuration, input reference requirements, supply limits, and maximum frequency before releasing a substitute to production. The ICS558G-01T packaging code is the closest ordering option, while other ordering codes require a full manufacturer specification review.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The verified manufacturer and distributor listings identify the device, electrical function, package, and supply range but do not provide explicit environmental-compliance declarations.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-11 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

ICS558G-01 datasheet ICS558G-01 datasheet pdf ICS558G-01 pinout ICS558G-01 equivalent ICS558G-01 drop-in replacement ICS558G-01 cross reference ICS558G-01 vs ICS558G-01T ICS558G-01 250 MHz clock buffer ICS558G-01 16-TSSOP footprint ICS558G-01 clock distribution application ICS558G-01 price ICS558G-01 stock Renesas ICS558G-01

متعلقہ اجزاء اور اصطلاحات

Renesas Electronics ICS558G-01 ICS558G-01T 558G-01LFT clock fanout buffer clock distribution buffer clock and timing IC CMOS PECL three-state output 2:4 fanout divide-by-4 250 MHz 2.375 V to 5.5 V supply 16-TSSOP TSSOP package family surface-mount package low-skew output telecommunications backplane network interface industrial control test and measurement signal integrity output enable
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں