Renesas Electronics

ICS574MIT - 160MHz 1:4 Zero-Delay Buffer | Renesas

Teilenummer: ICS574MIT ✓ Aktiv
3.3 V Vdss 8-pin SOIC, 3.90 mm width Package 160 MHz Speed
MOQ: 1 |

ICS574MIT Übersicht

The Renesas Electronics ICS574MIT is a PLL-based zero-delay fanout buffer operating up to 160 MHz, with a 1:4 input-to-output ratio and four low-skew CMOS outputs in an 8-pin SOIC package. It is designed for high-speed systems requiring closely aligned clock signals and negligible propagation delay.

A zero-delay buffer is a clock-distribution device that uses phase-locked-loop technology to compensate for internal and board propagation delay. In the clock and timing hierarchy, the ICS574MIT belongs to the fanout-buffer class, where a single periodic input is reproduced across multiple outputs with tightly controlled skew. This makes it useful when several sequential logic sections must receive a common clock without accumulating separate distribution delays.

The ICS574MIT provides a maximum operating frequency of 160 MHz, four outputs, and a 1:4 fanout ratio. Its CMOS input and output interface operates from a 3.3 V supply. Connecting one output directly to the FBIN feedback input aligns the rising edge of each output with the rising edge of the feedback signal, supporting deterministic clock relationships across the distributed network.

Internally, the device uses proprietary low-jitter PLL techniques to generate four low-skew outputs. This architecture is intended for high-speed processor, memory, networking, and communications systems where clock skew can limit setup and hold timing margin. Its single-input, four-output organization reduces the number of separate buffers required when several destination devices must operate from the same source clock.

Typical uses include memory clock distribution, network-interface clock fanout, high-speed digital backplanes, processor clock routing, and communication equipment. The device is particularly useful where the source clock must reach multiple endpoints while maintaining a controlled relationship between output edges. The compact 8-pin SOIC package also supports conventional surface-mount PCB assembly.

For implementation, reserve the feedback path as a short, controlled connection from one clock output to FBIN, and observe the maximum operating frequency, supply-voltage, and output-loading limits in the manufacturer datasheet. Confirm the pin assignment and input/output timing relationship against the selected package suffix before releasing a PCB layout.

This product reference combines the Renesas manufacturer description, distributor specifications, package information, operating characteristics, and practical replacement guidance. It also identifies where a drop-in substitute cannot be established without additional manufacturer timing data, preventing a package-compatible candidate from being presented incorrectly as a production replacement.

Drop-in-Alternativen für ICS574MIT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

ICS574MIT Technische Daten

Device Type PLL-based zero-delay fanout buffer
Maximum Frequency 160 MHz
Input-to-Output Ratio 1:4
Anzahl der Ausgänge 4 outputs
Number of Circuits 1 circuit
Versorgungsspannung 3.3 V
Input Logic Level CMOS
Output Logic Level CMOS
PLL Yes
Gehäuse 8-pin SOIC, 3.90 mm width
Package Body Width 3.90 mm
Montageart Surface mount

ICS574MIT 3.90 mm Pinbelegungsleitfaden

Pinbelegung für ICS574MIT (3.90 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für ICS574MIT im 3.90 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ICS574MIT.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ICS574MIT ist geeignet für 6 Anwendungs: Memory Clock Distribution, Processor Clock Routing, Network Interface Clock Fanout, High-Speed Digital Backplane, Communications Equipment, High-Speed Digital Logic Trees.

🖥️

Memory Clock Distribution

The ICS574MIT is well suited to distributing one periodic clock to as many as four memory-facing sections at rates up to 160 MHz. Its 1:4 fanout ratio and PLL-based zero-delay operation help reduce differences in clock arrival time, supporting setup and hold margin in high-speed memory interfaces. Connect the source clock to the input and use one output as the FBIN feedback path according to the Renesas datasheet. Keep that feedback route short, provide a continuous ground reference, and account for capacitive loading at every destination. Before deployment, verify the memory controller's maximum clock rate and its tolerance for output skew, jitter, and edge distortion.

🖥️

Processor Clock Routing

The ICS574MIT can fan one processor clock into four low-skew destinations when a system requires synchronized clock arrival across a processor and nearby logic. Its PLL-based architecture compensates propagation delay through the feedback loop, while the 160 MHz maximum frequency covers many legacy high-speed digital platforms. The circuit uses one CMOS clock input, four CMOS outputs, and an FBIN connection from one output. Keep the feedback connection compact and match trace geometry where channel-to-channel skew matters. Validate the design against processor timing specifications, supply sensitivity, output loading, and the maximum transition-rate requirement of each receiver.

🌐

Network Interface Clock Fanout

The ICS574MIT is appropriate for network-interface clock trees that require one source to feed up to four endpoint circuits with controlled phase relationships. Four outputs at up to 160 MHz reduce the number of separate buffer stages and support a compact 8-pin SOIC implementation. The PLL feedback arrangement can compensate edge delay, but only if the FBIN path is routed as an intentional part of the timing loop. Keep traces short, terminate them according to the actual receiver topology, and avoid adding unverified stubs. Confirm skew and jitter limits against the network controller and physical-layer devices, especially when parallel data and clock travel across a backplane.

🌐

High-Speed Digital Backplane

The ICS574MIT can serve as a central fanout element in a high-speed digital backplane when several logic devices must launch from a common clock. Its four low-skew outputs and maximum 160 MHz operation help maintain edge alignment across several branches, while zero-delay feedback operation compensates much of the buffer propagation path. The design must still account for trace-length differences, connector and via discontinuities, receiver threshold variation, and capacitive loading. Use the shortest practical FBIN route and a low-impedance ground plane. Bench validation should measure output-to-output skew at the relevant supply voltage and temperature before the clock network is released for production.

🌐

Communications Equipment

The ICS574MIT fits communications equipment requiring several synchronized digital clock destinations within a compact package. A 1:4 fanout ratio permits one source to feed four CMOS logic blocks at up to 160 MHz, reducing component count compared with multiple single-output buffers. The PLL-based zero-delay architecture is valuable where predictable phase relationships matter more than a fixed propagation delay. Place the device near the clock-consuming circuitry, use a low-impedance supply and ground arrangement, and route FBIN directly from an output. Confirm the interface timing budget, allowable jitter, and operating temperature range for every connected communications block.

🔧

High-Speed Digital Logic Trees

The ICS574MIT can organize a high-speed digital logic tree by distributing one clock to four local destinations without relying on multiple unrelated buffer paths. This application benefits from the device's low-skew outputs, zero-delay feedback behavior, and operation up to 160 MHz. The four outputs should be routed according to the destination timing requirements, while FBIN is connected to the designated feedback output with minimal trace length. Maintain a continuous return path beneath clock traces and use consistent layer transitions where possible. Before implementation, verify output loading, rise and fall time at each receiver, duty-cycle distortion, and the relationship between internal clock boundaries and external system timing.

Zusammenfassung der empfohlenen Produkte

ICS574MIT Renesas Electronics Verwendet in: Memory Clock Distribution, Processor Clock Routing, Network Interface Clock Fanout, High-Speed Digital Backplane, Communications Equipment, High-Speed Digital Logic Trees ICS574 manufacturer clock-buffer family Verwendet in: Memory Clock Distribution, Processor Clock Routing, Network Interface Clock Fanout, High-Speed Digital Backplane, Communications Equipment, High-Speed Digital Logic Trees
What is the ICS574MIT?
The ICS574MIT is a Renesas Electronics PLL-based zero-delay fanout buffer with one CMOS clock input, four CMOS outputs, and a maximum operating frequency of 160 MHz. According to the Renesas ICS574 manufacturer datasheet, it uses proprietary low-jitter PLL techniques to provide four low-skew outputs for high-speed clock-distribution systems. The device is packaged in an 8-pin SOIC and is intended for applications where multiple logic sections need a closely aligned clock.
What is the maximum frequency of the ICS574MIT?
The ICS574MIT operates up to 160 MHz. The Renesas ICS574 datasheet identifies the part as a low-jitter, low-skew PLL-based zero-delay buffer providing four outputs at speeds up to 160 MHz at a 3.3 V supply. Actual usable clock rate also depends on output loading, trace topology, PCB skew, downstream timing margin, and the operating conditions of the connected devices.
Where can I download the ICS574MIT datasheet PDF?
The official ICS574MIT datasheet is available from Renesas Electronics at https://www.renesas.com/en/document/dst/574-datasheet. That document contains the device description, timing characteristics, electrical specifications, pin information, and application details for the ICS574 family. Use the manufacturer PDF when defining PCB connections, checking output loading, and confirming operating limits before releasing production hardware.
Where can I find the ICS574MIT pinout?
The ICS574MIT uses an 8-pin SOIC package, and its authoritative pin assignment is shown in the pin-description table of the Renesas ICS574 datasheet. Use that table when assigning the CMOS clock input, FBIN feedback connection, four clock outputs, supply, and ground. The distributor title identifies the package as 8-SOIC with a 3.90 mm body width, but package dimensions alone do not define the pin numbering.
How does the ICS574MIT achieve zero-delay operation?
The ICS574MIT achieves zero-delay operation by using PLL circuitry to compensate for buffer and feedback-path propagation time. The Renesas datasheet states that connecting one output directly to FBIN aligns the rising edge of each output with the rising edge of the feedback signal. The feedback route therefore forms part of the timing system and should be laid out as a short, controlled path.
When should I choose the ICS574MIT for clock distribution?
Choose the ICS574MIT when one periodic clock must drive four destinations while maintaining controlled output-edge relationships at rates up to 160 MHz. It is well suited to memory, processor, communications, and backplane clock trees because it combines one input, four outputs, low skew, and PLL compensation in an 8-pin SOIC. It is less suitable when only two destinations are needed or when a source already provides four independently buffered clock outputs.
What can replace the ICS574MIT?
A production drop-in replacement should provide the same 8-pin SOIC pin assignment, 1:4 clock ratio, 3.3 V operation, four outputs, PLL-based feedback behavior, and compatible timing characteristics. No verified alternate MPN with those requirements is identified for the ICS574MIT. Treat a generic PLL clock buffer as a redesign candidate rather than a guaranteed substitute, and verify its FBIN topology, output phase, load behavior, and timing margins.
Is the ICS574MIT the same as a standard fanout buffer?
The ICS574MIT is not merely an unbuffered four-way fanout; it contains a PLL-based zero-delay architecture. Renesas describes the device as using low-jitter PLL techniques and aligning output rising edges through the FBIN connection. A standard CMOS fanout buffer may replicate edges with fixed propagation delay, whereas the ICS574MIT compensates for delay within the feedback loop. The two devices therefore should not be treated as interchangeable without timing verification.
What are the key specifications engineers should know about the ICS574MIT?
The principal ICS574MIT specifications are a 160 MHz maximum clock frequency, 1:4 input-to-output ratio, four CMOS outputs, a 3.3 V supply, PLL-based zero-delay operation, and an 8-pin SOIC package. The Renesas manufacturer datasheet also identifies the device as a low-jitter, low-skew fanout buffer. Output skew, jitter, propagation delay, and temperature limits must be taken from the timing tables for the exact ordering code.
What is the best Renesas equivalent for the ICS574MIT?
No distinct Renesas drop-in equivalent is established for the ICS574MIT in the available cross-reference results. The manufacturer supports the ICS574 family, but an ordering suffix can represent package, temperature, or shipping-code differences rather than a distinct functional replacement. When a second source is required, request a Renesas-approved alternative and require written confirmation of SOIC-8 pin compatibility, 3.3 V operation, 160 MHz capability, and equivalent PLL feedback behavior.
How should the ICS574MIT FBIN connection be routed?
Route one of the four ICS574MIT outputs directly to FBIN as specified by the Renesas datasheet, keeping the feedback path short and electrically controlled. Because this connection establishes the phase relationship used by the PLL, unnecessary vias, long traces, and stubs can degrade edge alignment. Use a solid ground reference and place any required decoupling capacitors close to the device according to the manufacturer layout recommendations.
Does the ICS574MIT require an external crystal?
The ICS574MIT is listed as a zero-delay fanout buffer with a CMOS input, so its clock source is presented at the device input rather than generated from an internal crystal oscillator. The supplied manufacturer description identifies PLL-based feedback compensation but does not indicate an integrated oscillator or crystal oscillator. Connect the periodic source signal to the designated clock input and use FBIN as directed by the datasheet pin-description and application diagrams.
Is the ICS574MIT suitable for memory clock distribution?
The ICS574MIT is suitable for memory clock distribution when the target interface can operate at up to 160 MHz and requires four closely related outputs. Its PLL-based zero-delay function can reduce clock arrival differences among multiple destinations, while the 1:4 fanout ratio matches four clock-consuming sections. Confirm device-specific setup and hold timing, trace skew, load capacitance, and the maximum frequency permitted by each memory device.
Where can I buy the ICS574MIT, and what is its lead time?
Use the Request a Quote form on this page to ask for current ICS574MIT availability, unit pricing, minimum order quantity, and production lead time. The manufacturer and distributor records confirm an 8-pin SOIC device with a 160 MHz maximum frequency, but they do not state a current XAIPART stock quantity. The quote form is the appropriate route for obtaining a current commercial commitment before procurement.
How should I validate a possible ICS574MIT replacement?
Validate an ICS574MIT replacement by comparing the complete 8-pin SOIC pin map, 3.3 V supply range, 1:4 fanout ratio, four-output architecture, FBIN feedback topology, maximum frequency, output rise and fall times, output skew, jitter, and CMOS loading behavior. Compare worst-case values over temperature and supply voltage, then measure edge alignment on the assembled PCB. A matching package and frequency alone do not establish drop-in equivalence.

Technische Referenzdaten für ICS574MIT – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ICS574MIT when a 3.3 V system clock must feed four CMOS destinations at up to 160 MHz and the clock edges must remain closely aligned. Its PLL-based FBIN feedback arrangement is especially useful in legacy memory, processor, network-interface, backplane, and communications clock trees where multiple independent fanout stages would introduce additional propagation delay. The compact 8-pin SOIC also simplifies PCB placement compared with a multi-buffer implementation. A conventional fanout buffer may be preferable when fixed propagation delay is acceptable and absolute phase alignment is unnecessary. Do not select a substitute solely from its package and frequency rating: verify the complete pin map, output phase, feedback configuration, loading behavior, skew, jitter, and timing limits. When the requirement includes a second-source drop-in part, require manufacturer confirmation or demonstrate equivalence through worst-case timing measurements on representative hardware.

Vergleich mit Alternativen

Parameter Dieses Produkt
Package 8-pin SOIC, 3.90 mm width
Brand Renesas Electronics
Device Type PLL-based zero-delay fanout buffer
Maximum Frequency 160 MHz
Input-to-Output Ratio 1:4
Number of Outputs 4 outputs
Supply Voltage 3.3 V
Logic Interface CMOS input and CMOS output
PLL Architecture Yes
Feedback Connection FBIN connected to an output

Wichtigste Unterscheidungsmerkmale

  • PLL-based zero-delay clock compensation (vs. A conventional CMOS fanout buffer)
  • Four outputs from one clock input (vs. A single-output CMOS buffer)
  • Compact high-speed integration (vs. A discrete multi-stage clock tree)

Designhinweise

Treat FBIN as a timing-critical feedback route rather than an ordinary clock branch. Connect one of the four outputs directly to FBIN as specified by the Renesas ICS574 datasheet, minimize vias and stubs, and keep the route short enough to preserve the intended phase relationship. Place the device close to the clock-consuming logic when possible, use consistent trace geometry for adjacent outputs, and provide a continuous ground reference beneath the clock routing.

Validate the complete clock tree at the receiver rather than relying only on the nominal 160 MHz rating. Measure output rise and fall times, duty-cycle distortion, output-to-output skew, and edge alignment at the intended load. Include realistic PCB capacitance and connector loading in the evaluation. If a substitute device is considered, compare its feedback topology and measured timing behavior because a conventional four-output buffer can have a different propagation-delay relationship even when its frequency rating is identical.

Do not assume that any 1:4 CMOS buffer with a 160 MHz rating is interchangeable with the ICS574MIT. A valid replacement must also preserve the 8-pin SOIC pin map, 3.3 V operating conditions, four-output arrangement, PLL-based phase compensation, and FBIN implementation. Check the exact ordering suffix before assembly because package, temperature, and shipping codes can differ. Confirm the manufacturer pin table and the Renesas timing specification before approving a substitution.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer description and distributor records do not state the requested compliance classifications. The ICS574MIT is an 8-pin SOIC clock-generation and timing IC, so SOA is not applicable.

Daten verifiziert am: 2026-11-16 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

ICS574MIT datasheet ICS574MIT specifications ICS574MIT pinout ICS574MIT datasheet pdf ICS574MIT equivalent ICS574MIT replacement ICS574MIT cross reference ICS574MIT SOIC-8 footprint ICS574MIT price ICS574MIT stock Renesas ICS574MIT ICS574MIT 160MHz zero delay buffer ICS574MIT clock fanout what can replace ICS574MIT

Verwandte Bauteile & Begriffe

Renesas Electronics ICS574MIT ICS574 zero-delay buffer fanout buffer clock buffer clock distribution clock and timing IC PLL phase-locked loop CMOS FBIN 160 MHz 1:4 fanout four-output clock buffer low-skew clock low-jitter clock 8-pin SOIC SOIC-8 surface-mount package semiconductor memory clock distribution processor clock routing network interface clocking high-speed digital backplane
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen