ICS574MIT - 160MHz 1:4 Zero-Delay Buffer | Renesas
MPN: ICS574MIT ✓ פעילICS574MIT סקירה
A zero-delay buffer is a clock-distribution device that uses phase-locked-loop technology to compensate for internal and board propagation delay. In the clock and timing hierarchy, the ICS574MIT belongs to the fanout-buffer class, where a single periodic input is reproduced across multiple outputs with tightly controlled skew. This makes it useful when several sequential logic sections must receive a common clock without accumulating separate distribution delays.
The ICS574MIT provides a maximum operating frequency of 160 MHz, four outputs, and a 1:4 fanout ratio. Its CMOS input and output interface operates from a 3.3 V supply. Connecting one output directly to the FBIN feedback input aligns the rising edge of each output with the rising edge of the feedback signal, supporting deterministic clock relationships across the distributed network.
Internally, the device uses proprietary low-jitter PLL techniques to generate four low-skew outputs. This architecture is intended for high-speed processor, memory, networking, and communications systems where clock skew can limit setup and hold timing margin. Its single-input, four-output organization reduces the number of separate buffers required when several destination devices must operate from the same source clock.
Typical uses include memory clock distribution, network-interface clock fanout, high-speed digital backplanes, processor clock routing, and communication equipment. The device is particularly useful where the source clock must reach multiple endpoints while maintaining a controlled relationship between output edges. The compact 8-pin SOIC package also supports conventional surface-mount PCB assembly.
For implementation, reserve the feedback path as a short, controlled connection from one clock output to FBIN, and observe the maximum operating frequency, supply-voltage, and output-loading limits in the manufacturer datasheet. Confirm the pin assignment and input/output timing relationship against the selected package suffix before releasing a PCB layout.
This product reference combines the Renesas manufacturer description, distributor specifications, package information, operating characteristics, and practical replacement guidance. It also identifies where a drop-in substitute cannot be established without additional manufacturer timing data, preventing a package-compatible candidate from being presented incorrectly as a production replacement.
חלופות תחליף ישיר עבור ICS574MIT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותICS574MIT מפרטים
| Device Type | PLL-based zero-delay fanout buffer |
| Maximum Frequency | 160 MHz |
| Input-to-Output Ratio | 1:4 |
| מספר יציאות | 4 outputs |
| Number of Circuits | 1 circuit |
| מתח אספקה | 3.3 V |
| Input Logic Level | CMOS |
| Output Logic Level | CMOS |
| PLL | Yes |
| מארז | 8-pin SOIC, 3.90 mm width |
| Package Body Width | 3.90 mm |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של ICS574MIT 3.90 mm
תצורת פינים עבור ICS574MIT (מארזת 3.90 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור ICS574MIT.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
ICS574MIT מתאים עבור 6 יישוםs: Memory Clock Distribution, Processor Clock Routing, Network Interface Clock Fanout, High-Speed Digital Backplane, Communications Equipment, High-Speed Digital Logic Trees.
Memory Clock Distribution
The ICS574MIT is well suited to distributing one periodic clock to as many as four memory-facing sections at rates up to 160 MHz. Its 1:4 fanout ratio and PLL-based zero-delay operation help reduce differences in clock arrival time, supporting setup and hold margin in high-speed memory interfaces. Connect the source clock to the input and use one output as the FBIN feedback path according to the Renesas datasheet. Keep that feedback route short, provide a continuous ground reference, and account for capacitive loading at every destination. Before deployment, verify the memory controller's maximum clock rate and its tolerance for output skew, jitter, and edge distortion.
מומלץ
Processor Clock Routing
The ICS574MIT can fan one processor clock into four low-skew destinations when a system requires synchronized clock arrival across a processor and nearby logic. Its PLL-based architecture compensates propagation delay through the feedback loop, while the 160 MHz maximum frequency covers many legacy high-speed digital platforms. The circuit uses one CMOS clock input, four CMOS outputs, and an FBIN connection from one output. Keep the feedback connection compact and match trace geometry where channel-to-channel skew matters. Validate the design against processor timing specifications, supply sensitivity, output loading, and the maximum transition-rate requirement of each receiver.
מומלץ
Network Interface Clock Fanout
The ICS574MIT is appropriate for network-interface clock trees that require one source to feed up to four endpoint circuits with controlled phase relationships. Four outputs at up to 160 MHz reduce the number of separate buffer stages and support a compact 8-pin SOIC implementation. The PLL feedback arrangement can compensate edge delay, but only if the FBIN path is routed as an intentional part of the timing loop. Keep traces short, terminate them according to the actual receiver topology, and avoid adding unverified stubs. Confirm skew and jitter limits against the network controller and physical-layer devices, especially when parallel data and clock travel across a backplane.
מומלץ
High-Speed Digital Backplane
The ICS574MIT can serve as a central fanout element in a high-speed digital backplane when several logic devices must launch from a common clock. Its four low-skew outputs and maximum 160 MHz operation help maintain edge alignment across several branches, while zero-delay feedback operation compensates much of the buffer propagation path. The design must still account for trace-length differences, connector and via discontinuities, receiver threshold variation, and capacitive loading. Use the shortest practical FBIN route and a low-impedance ground plane. Bench validation should measure output-to-output skew at the relevant supply voltage and temperature before the clock network is released for production.
מומלץ
Communications Equipment
The ICS574MIT fits communications equipment requiring several synchronized digital clock destinations within a compact package. A 1:4 fanout ratio permits one source to feed four CMOS logic blocks at up to 160 MHz, reducing component count compared with multiple single-output buffers. The PLL-based zero-delay architecture is valuable where predictable phase relationships matter more than a fixed propagation delay. Place the device near the clock-consuming circuitry, use a low-impedance supply and ground arrangement, and route FBIN directly from an output. Confirm the interface timing budget, allowable jitter, and operating temperature range for every connected communications block.
מומלץ
High-Speed Digital Logic Trees
The ICS574MIT can organize a high-speed digital logic tree by distributing one clock to four local destinations without relying on multiple unrelated buffer paths. This application benefits from the device's low-skew outputs, zero-delay feedback behavior, and operation up to 160 MHz. The four outputs should be routed according to the destination timing requirements, while FBIN is connected to the designated feedback output with minimal trace length. Maintain a continuous return path beneath clock traces and use consistent layer transitions where possible. Before implementation, verify output loading, rise and fall time at each receiver, duty-cycle distortion, and the relationship between internal clock boundaries and external system timing.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ICS574MIT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Package | 8-pin SOIC, 3.90 mm width |
| Brand | Renesas Electronics |
| Device Type | PLL-based zero-delay fanout buffer |
| Maximum Frequency | 160 MHz |
| Input-to-Output Ratio | 1:4 |
| Number of Outputs | 4 outputs |
| Supply Voltage | 3.3 V |
| Logic Interface | CMOS input and CMOS output |
| PLL Architecture | Yes |
| Feedback Connection | FBIN connected to an output |
מבדילים עיקריים
- PLL-based zero-delay clock compensation (לעומתA conventional CMOS fanout buffer)
- Four outputs from one clock input (לעומתA single-output CMOS buffer)
- Compact high-speed integration (לעומתA discrete multi-stage clock tree)
הערות תכנון
Treat FBIN as a timing-critical feedback route rather than an ordinary clock branch. Connect one of the four outputs directly to FBIN as specified by the Renesas ICS574 datasheet, minimize vias and stubs, and keep the route short enough to preserve the intended phase relationship. Place the device close to the clock-consuming logic when possible, use consistent trace geometry for adjacent outputs, and provide a continuous ground reference beneath the clock routing.
Validate the complete clock tree at the receiver rather than relying only on the nominal 160 MHz rating. Measure output rise and fall times, duty-cycle distortion, output-to-output skew, and edge alignment at the intended load. Include realistic PCB capacitance and connector loading in the evaluation. If a substitute device is considered, compare its feedback topology and measured timing behavior because a conventional four-output buffer can have a different propagation-delay relationship even when its frequency rating is identical.
Do not assume that any 1:4 CMOS buffer with a 160 MHz rating is interchangeable with the ICS574MIT. A valid replacement must also preserve the 8-pin SOIC pin map, 3.3 V operating conditions, four-output arrangement, PLL-based phase compensation, and FBIN implementation. Check the exact ordering suffix before assembly because package, temperature, and shipping codes can differ. Confirm the manufacturer pin table and the Renesas timing specification before approving a substitution.
מידע על תאימות
The manufacturer description and distributor records do not state the requested compliance classifications. The ICS574MIT is an 8-pin SOIC clock-generation and timing IC, so SOA is not applicable.