INA121UAG4 - Low-Power FET Instrumentation Amplifier | Texas Instruments
Teilenummer: INA121UAG4 ✗ AbgekündigtINA121UAG4 Übersicht
An instrumentation amplifier is a differential amplifier optimized for amplifying a small voltage difference between two inputs while rejecting common-mode voltage. The INA121 belongs to the broader hierarchy of differential amplifiers, analog signal-chain ICs, and amplifiers used within electronic instrumentation. Its three-op-amp architecture provides precision differential amplification in a compact surface-mount package without requiring separate precision resistor networks.
The INA121's principal benefits include programmable gain from 1 V/V to 1000 V/V, low quiescent current, low input offset voltage, and high common-mode rejection ratio. The internal gain-setting resistor allows the gain to be selected with one external resistor while preserving the small package size. These characteristics are useful when the measured differential voltage is much smaller than the voltage common to both input terminals.
The INA121 uses a three-op-amp signal architecture with FET-input stages to provide high input impedance. The differential input is amplified according to the selected external gain resistor, while internal feedback networks reject common-mode voltage and improve gain accuracy. Input protection and feedback arrangements should be checked against the operating input range before connecting sensors whose outputs may exceed the electrical limits.
Typical uses include bridge-transducer measurement, current sensing, biomedical instrumentation, portable measurement equipment, and industrial sensor interfaces. The device can also amplify differential voltages in test and measurement systems when its input, output, supply, and common-mode limits are respected. Its surface-mount package supports compact analog front ends but requires careful grounding and stable reference arrangements.
For best results, place the gain-setting resistor close to the gain pin, connect the reference connection to a low-impedance ground for unipolar output or to a precision midpoint for bipolar output, and provide adequate supply bypassing. Output-voltage headroom, common-mode range, input bias-current effects, and resistor tolerance must all be considered when defining the usable measurement range.
This page combines the manufacturer product information, lifecycle and package details, sourced cross-reference candidates, application guidance, and practical design considerations. It also distinguishes confirmed package and lifecycle facts from electrical parameters that require direct confirmation against the current Texas Instruments datasheet before a new design is released.
Drop-in-Alternativen für INA121UAG4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit INA121UAG4 (gleiche Bauform und Footprint) – abweichend in Architecture, Package, Quiescent Current, Gain Configuration, Gain Range.
INA126U
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →INA126UA
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →INA129U
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →INA121UAG4 Grenzwerte & elektrische Eigenschaften
| Keine Spezifikationen verfügbar |
INA121UAG4 standard Pinbelegungsleitfaden
Pinbelegung für INA121UAG4 (standard-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für INA121UAG4.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
INA121UAG4 ist geeignet für 6 Anwendungs: Bridge Transducer Amplification, Precision Current Sensing, Biomedical Sensor Signal Conditioning, Portable Instrumentation, Laboratory Data Acquisition, Industrial Sensor Interface.
Bridge Transducer Amplification
The INA121UAG4 suits Wheatstone bridge sensing because its FET-input instrumentation-amplifier architecture amplifies the small differential voltage generated by resistance changes while rejecting common-mode voltage. A programmed gain from 1 V/V to 1000 V/V allows the output range to be matched to a bridge excitation and ADC input. The external gain resistor should use a low-tolerance, low-temperature-coefficient network because its error directly becomes gain error. Verify bridge excitation voltage, input common-mode range, output swing, and reference configuration before operation.
Empfohlen
Precision Current Sensing
INA121UAG4 can amplify the differential voltage produced by a current-sense shunt when the signal is small relative to the shunt's common-mode voltage. Its high-impedance FET inputs reduce disturbance of the shunt and support programmed gain up to 1000 V/V. Layout should use a short Kelvin-style connection from the shunt to the amplifier, separate input returns from power-return currents, and local supply bypass. Confirm the shunt voltage, common-mode limits, output swing, and amplifier settling behavior before selecting a gain.
Empfohlen
Biomedical Sensor Signal Conditioning
The INA121UAG4 is applicable to low-amplitude differential sensor signals in biomedical and diagnostic equipment when high input impedance and common-mode rejection are important. Its compact 8-pin SOIC footprint permits placement close to the sensor connector, while programmable gain adapts the signal to an ADC or controller input. For patient-connected designs, isolation, protection, leakage, creepage, and applicable medical-device requirements must be evaluated separately; the amplifier's specified operating range alone does not establish patient-safety compliance.
Empfohlen
Portable Instrumentation
INA121UAG4 fits portable measurement systems where power efficiency, compactness, and accurate differential amplification are required. The low-power instrumentation-amplifier configuration combines a small SOIC footprint with a gain range of 1 V/V to 1000 V/V, allowing one analog-front-end design to cover multiple sensor sensitivities. Battery-operated equipment should account for quiescent current, startup behavior, reference current, and the input bias current required by the chosen gain resistor when estimating battery life.
Empfohlen
Laboratory Data Acquisition
INA121UAG4 provides the analog front end for laboratory DAQ modules that must measure small differential voltages superimposed on larger common-mode levels. The FET-input stage and selectable gain support compatibility with sensors such as strain gauges, thermocouple interfaces, and bridge transducers. Keep the gain resistor and bypass capacitors close to the device, use a stable reference for bipolar signals, and provide analog and digital ground routing that avoids forcing return currents through the measurement node. Confirm settling and input-range requirements against the actual signal bandwidth.
Empfohlen
Industrial Sensor Interface
INA121UAG4 can condition differential outputs from industrial sensors when the system operates within the amplifier's 4 V to 36 V supply range and -40 °C to +85 °C temperature range. Its three-op-amp architecture provides gain and common-mode rejection in a compact 8-pin SOIC, reducing the number of discrete precision elements required. Industrial equipment should add appropriate surge and transient protection, isolate long sensor wiring from sensitive inputs, and verify that normal signal excursions remain inside the electrical limits throughout the complete gain range.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für INA121UAG4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | INA126U | INA126UA | INA129U |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | FET-input instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier |
| Maximum Gain | 1000 V/V | 10000 V/V | 10000 V/V | 10000 V/V |
| Special Features | Three-op-amp architecture and low-power operation | Gain up to 10000 V/V | Gain up to 10000 V/V | Gain up to 10000 V/V |
Wichtigste Unterscheidungsmerkmale
- Focused gain range for precision differential measurement (vs. INA126U)
- Established low-power FET-input architecture (vs. INA129U)
- Compact eight-pin surface-mount implementation (vs. INA126UA)
Designhinweise
Place the gain-setting resistor close to its designated INA121 pin and keep the input traces short, symmetrical, and away from switching nodes. Connect the amplifier's reference pin directly to a low-impedance analog ground for unipolar operation or to a carefully filtered precision midpoint for bipolar signals. A high-impedance reference node can introduce offset and noise, so avoid routing the reference connection beside digital clocks or power inductors.
Provide local supply bypass close to the device and maintain the required voltage difference between input, output, and supply pins at every selected gain. Higher gain does not simply increase output amplitude; it also narrows the usable input and output common-mode range. Validate the signal excursion against those limits across temperature and tolerance, and verify startup behavior if the measurement system must distinguish valid readings from an unpowered or settling amplifier.
Do not select INA121UAG4 solely from the 8-pin SOIC outline when comparing it with INA126U, INA126UA, or INA129U. Check the gain-resistor connection, input and output common-mode limits, supply range, reference configuration, and absolute maximum ratings. The three related candidates support gains up to 10000 V/V, whereas INA121UAG4 reaches 1000 V/V, so a footprint-compatible device may still be electrically unsuitable for the original board.
Use a solid ground reference and return sensor current directly to the analog supply ground without routing it through the measurement reference node. For bridge and shunt measurements, use paired input routing to minimize differential pickup from adjacent switching signals. Input filtering, if required, should preserve phase margin and sensor bandwidth; excessive series resistance can combine with input bias current to create gain error, while excessive capacitance can impair settling.
Compliance-Informationen
The component listing identifies the part as ROHS3 compliant. No separate REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was confirmed for this exact order code.