Texas Instruments

INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI

Teilenummer: INA2141UA ✓ Aktiv
Low power Vdss 16-pin SOIC, 0.295 inch (7.50 mm) width Package
MOQ: 1 |

INA2141UA Übersicht

The Texas Instruments INA2141UA is a dual, low-power instrumentation amplifier in a 16-pin SOIC package, with signal gain options of 10 and 100 and a listed gain-bandwidth product of 200 kHz. It is designed for amplifying small differential sensor signals in industrial measurement, instrumentation, and analog front-end systems. The package is identified as 16-SOIC, measuring 0.295 inch, or 7.50 mm, in body width.

An instrumentation amplifier is a precision analog amplifier optimized for differential signals. Its internal architecture amplifies the voltage difference between two inputs while rejecting common-mode noise, which is important when a sensor output is small relative to the surrounding electrical environment. The INA2141 belongs to the wider category of operational amplifier ICs and analog signal-chain devices used to condition, scale, and route sensor signals before conversion or control.

Key confirmed features include dual amplifier channels, low-power operation, selectable gains of 10 and 100, a 200 kHz listed bandwidth figure, and a 16-pin SOIC package. The dual configuration allows one device to serve two independent analog channels, reducing component count when the board area is constrained. The two gain settings also support different sensor ranges without changing the overall signal-chain architecture.

The device uses a three-operational-amplifier instrumentation-amplifier approach to provide differential input handling and high common-mode rejection. Exact input common-mode range, output swing, supply range, input bias current, offset voltage, noise density, and quiescent current should be confirmed in the manufacturer datasheet before the circuit is released for production.

Typical uses include bridge-sensor front ends, pressure and force measurement, current-shunt monitoring, battery-cell sensing, and industrial instrumentation. The dual-channel arrangement is particularly useful when two sensors must be measured under similar electrical conditions, while the 200 kHz gain-bandwidth figure supports signal bandwidths appropriate for many slow-to-moderate industrial sensing tasks.

Design layouts should provide short, symmetric input traces, a stable reference configuration, and careful grounding around the analog inputs. Because the INA2141UA operates in a differential measurement environment, input filtering, protection, and connector grounding determine whether the amplifier sees the intended signal or external interference.

This page consolidates the confirmed ordering information, package details, functional attributes, application fit, and replacement considerations. It also identifies the technical parameters that should be checked in the manufacturer datasheet before schematic sign-off, helping engineers move from part selection to a validated analog front-end design.

Drop-in-Alternativen für INA2141UA – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

INA2141UA Grenzwerte & elektrische Eigenschaften

Device Type Dual instrumentation amplifier
Number of Channels 2 channels
Gain 10 or 100 V/V
Listed Gain-Bandwidth Product 200 kHz
Supply Type Low power
Gehäuse 16-pin SOIC, 0.295 inch (7.50 mm) width
Montageart Surface mount
Input Type Differential

INA2141UA 16-pin soic, 0.295 inch (7.50 mm) width Pinbelegungsleitfaden

Pinbelegung für INA2141UA (16-pin soic, 0.295 inch (7.50 mm) width-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für INA2141UA im 16-pin soic, 0.295 inch (7.50 mm) width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für INA2141UA.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

INA2141UA ist geeignet für 6 Anwendungs: Bridge Sensor Measurement, Current Shunt Amplification, Pressure and Force Transducers, Battery Cell Monitoring, Industrial Process Sensing, Precision Instrumentation Signal Conditioning.

🏭

Bridge Sensor Measurement

The INA2141UA suits Wheatstone-bridge front ends because each channel amplifies the differential voltage generated by a small change in bridge balance while the two inputs share a larger excitation-related voltage. The confirmed gain settings of 10 and 100 let the same analog front end support sensors with different sensitivities. Use the 16-pin SOIC device when two bridge channels must fit in a compact board area, and verify the bridge excitation voltage against the amplifier input common-mode range before layout release.

⚡

Current Shunt Amplification

A low-ohm current shunt produces a small differential voltage proportional to the monitored current, and the INA2141UA is suited to amplifying that voltage without adding a separate differential amplifier stage. Gain of 10 offers a lower-noise route for larger shunt drops, while gain of 100 increases sensitivity for smaller drops. Place the shunt close to the amplifier inputs, route the pair symmetrically, and confirm the maximum input common-mode voltage for the highest shunt current in the design.

🔧

Pressure and Force Transducers

Piezoresistive pressure cells and strain-gauge force sensors commonly deliver a small differential output around a substantial common-mode bias. The differential input architecture of the INA2141UA is appropriate for conditioning these outputs, and the dual 16-SOIC package can serve two sensors under similar mechanical conditions. Confirm the selected gain against sensor sensitivity, then check offset, bias current, and common-mode rejection requirements in the manufacturer datasheet.

🔋

Battery Cell Monitoring

Battery-management systems often use instrumentation amplifiers to measure small differential cell voltages with a high common-mode potential relative to ground. The INA2141UA's dual-channel configuration can process two monitored inputs while its gain settings of 10 or 100 provide useful scaling options. Verify the complete battery-pack voltage against the device supply rating, keep the input pair short, and confirm that the reference configuration permits accurate midpoint measurement.

🌐

Industrial Process Sensing

Temperature, level, and process-control sensors can present low-level differential outputs that must be amplified before an ADC or controller samples them. The INA2141UA combines two low-power instrumentation-amplifier channels in a 16-pin SOIC package, reducing board area in multi-channel industrial equipment. The listed 200 kHz gain-bandwidth product supports moderate-bandwidth process signals, while the selected gain determines the practical closed-loop bandwidth and should be checked against required settling time.

📟

Precision Instrumentation Signal Conditioning

Laboratory and test instruments frequently need to reject noise shared by a pair of sensor lines while amplifying a small differential command or measurement. The INA2141UA provides a matched dual-channel implementation in a 16-pin SOIC package, and each channel can operate at gain 10 or 100. Use matched input filtering and solid grounding to preserve differential accuracy, and confirm the output swing and settling behavior needed by the measurement acquisition chain.

What is the INA2141UA?
The INA2141UA is a Texas Instruments dual, low-power instrumentation amplifier in a 16-pin SOIC package. According to the Texas Instruments INA2141 product page, it supports gain settings of 10 and 100, while distributor product records identify a 200 kHz gain-bandwidth figure. It is intended for differential sensor-signal conditioning where small sensor outputs must be amplified without responding strongly to voltage common to both inputs.
How many amplifiers are in the INA2141UA package?
The INA2141UA contains two independent instrumentation-amplifier circuits. The Texas Instruments product page identifies the device as a dual amplifier, and distributor records describe it as a two-circuit 16-SOIC package. Using both channels can reduce board area when two similar sensors require differential measurement, although each channel needs its own input, reference, feedback, and output network.
What gain settings does the INA2141UA support?
The INA2141UA supports gain settings of 10 and 100 V/V. The Texas Instruments INA2141 product page lists the device as a dual instrumentation amplifier with G = 10 and G = 100 options. Gain selection is implemented through the device's gain-setting network, so the final gain should be verified against the pin-connection table and reference configuration in the manufacturer datasheet.
What is the bandwidth of the INA2141UA?
The INA2141UA is listed with a 200 kHz gain-bandwidth product. This figure should be interpreted together with the selected gain: a gain of 10 gives an approximate closed-loop bandwidth of 20 kHz, while a gain of 100 gives approximately 2 kHz when the listed gain-bandwidth product is assumed to remain constant. Confirm the exact frequency response, settling time, and gain-error curves in the manufacturer datasheet.
What package does the INA2141UA use?
The INA2141UA is supplied in a 16-pin SOIC package with a listed body width of 0.295 inch, or 7.50 mm. Distributor records identify the package as 16-SOIC, and the corresponding package-diagram asset is soic-16. Confirm pin assignment and exposed-pad requirements from the manufacturer datasheet before assigning PCB tracks or defining the assembly footprint.
Where can I download the INA2141UA datasheet?
The INA2141UA datasheet is available through the Texas Instruments INA2141 product page and the manufacturer datasheet link listed on this page. The document provides the authoritative pinout, recommended application circuits, electrical characteristics, gain-setting configuration, and recommended PCB layout. Use the pin-description table when assigning board nets and verify the latest manufacturer revision before releasing the design.
Where is the INA2141UA pinout?
The INA2141UA pinout is documented in the Texas Instruments INA2141 datasheet because it uses a 16-pin SOIC package with two amplifier channels. Each channel includes differential inputs and its own signal-path pins, while power and common pins are shared. Assign PCB nets directly from the manufacturer pin-description table rather than inferring the arrangement from a generic SOIC footprint.
Can the INA2141UA be used for bridge sensor measurement?
Yes, the INA2141UA is suitable for differential bridge-sensor front ends because its instrumentation-amplifier architecture amplifies the difference between two input voltages. A typical circuit connects the bridge excitation to the supply or a regulated excitation rail, applies the two bridge nodes to a channel input pair, and returns a differential voltage proportional to bridge imbalance. Confirm the input common-mode range before choosing the excitation voltage.
Is the INA2141UA suitable for current-shunt monitoring?
Yes, the INA2141UA can amplify the small differential voltage generated by a low-ohm current shunt. A gain of 10 preserves low-level measurements that might otherwise be buried in offset or noise, while gain of 100 increases sensitivity when the shunt drop is small. Keep the shunt and amplifier input traces compact and place filtering close to the input pins to limit pickup from surrounding switching circuitry.
When should I choose the INA2141UA over a general-purpose op amp?
Choose the INA2141UA when the source is differential and common-mode rejection matters more than using three discrete amplifiers. Its instrumentation-amplifier configuration is intended to amplify a small difference between two inputs while rejecting a larger shared voltage, and the dual 16-SOIC package integrates two matching channels. A general-purpose op amp may be preferable for single-ended signals, special filtering functions, or applications outside its confirmed input and output ranges.
What is the best drop-in replacement for the INA2141UA?
No verified drop-in replacement for the INA2141UA is identified in the available cross-reference records. A genuine drop-in candidate must preserve the 16-pin SOIC footprint, pin-to-pin function, dual-channel architecture, and operation across the required supply and common-mode ranges. Submit the target MPN and required electrical limits through the cross-reference workflow for evaluation, and confirm any proposed substitute against the manufacturer datasheet before PCB release.
What can replace the INA2141UA in an analog front end?
The INA2141UA can be functionally replaced only after verifying supply voltage, gain configuration, common-mode range, output swing, bandwidth, and noise requirements. An instrumentation amplifier with a different pin arrangement may require PCB changes even if its electrical performance is acceptable. Request a pin-to-pin cross-reference review for this MPN, and treat the Request a Quote form on this page as the commercial contact for supply and replacement-part inquiries.
Is the INA2141UA better than the INA213 for dual-channel designs?
The INA2141UA provides two instrumentation-amplifier channels in one 16-pin SOIC package, whereas the INA213 is identified as a single-channel device. A dual-channel design can therefore reduce package count and simplify board-area allocation when two similar differential measurements are required. The final comparison must also confirm that each device's gain settings, bandwidth, common-mode range, and supply limits meet the system requirements.
What are the key specifications of the INA2141UA that engineers should know?
The key confirmed characteristics are a dual instrumentation-amplifier configuration, selectable gains of 10 and 100, a listed 200 kHz gain-bandwidth product, and a 16-pin SOIC package measuring 0.295 inch or 7.50 mm in width. These facts make the device suitable for paired differential measurement channels. Supply limits, input offset, bias current, noise, common-mode range, and output swing must be taken from the manufacturer datasheet.
How do I reduce noise around the INA2141UA inputs?
Reduce noise by routing the two input lines as a short, tightly coupled pair, minimizing their enclosed area and keeping them away from switching nodes and high-current traces. Place input filtering capacitors close to the relevant pins, use a solid ground plane, and avoid routing inputs beneath noisy circuits. These layout measures preserve the differential nature of the measurement and prevent common-mode interference from being converted into differential error.
Where can I buy the INA2141UA online?
The INA2141UA is listed by Texas Instruments as an active part and is carried in distributor catalogs under the exact INA2141UA ordering code. Use the Request a Quote form on this page for current commercial availability, quantity, and lead-time confirmation. The form allows the request to be tied to the exact MPN without relying on a static pricing table that can become outdated.
What is the price of the INA2141UA?
Current INA2141UA pricing is not stated in this page because commercial prices change with inventory, quantity, and purchasing conditions. Use the Request a Quote form on this page to request the current price for the exact 16-pin SOIC ordering code. Confirm the quoted line item includes INA2141UA and the intended pack quantity before issuing a purchase order.
What is the lead time for the INA2141UA?
The current production and delivery lead time should be confirmed at the time of quotation because availability can change with demand and packaging requirements. Submit an INA2141UA request through the Request a Quote form on this page and state the required quantity and target ship date. The request should also confirm whether the standard 16-SOIC shipping configuration meets your assembly plan.
Is the INA2141UA in stock?
Inventory status changes continuously and should not be inferred from a distributor search-result page. The Texas Instruments product page identifies INA2141UA as an active product, while current quantity and delivery scheduling should be confirmed through the Request a Quote form on this page. Include your required quantity, annual usage, and target delivery date in the request for a practical supply assessment.

Technische Referenzdaten für INA2141UA – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the INA2141UA when the design needs two differential measurement channels, selectable gains of 10 or 100, and a compact 16-pin SOIC implementation. Its instrumentation-amplifier architecture is a strong fit for bridge sensors, strain gauges, and low-ohm shunts where a large common-mode voltage accompanies a small useful signal. Consider a general-purpose op amp instead when the source is single-ended or when the required gain, bandwidth, and output swing fall outside the INA2141 specifications. Do not treat a generic instrumentation amplifier as a drop-in replacement merely because it also uses a 16-pin package. A valid substitute must preserve pin-to-pin connectivity and channel organization while meeting the supply, common-mode, output-swing, noise, and bandwidth requirements. Because no confirmed pin-compatible alternatives are available, request a formal cross-reference evaluation before changing the component on an existing board.

Vergleich mit Alternativen

Parameter Dieses Produkt
Brand Texas Instruments
Package 16-pin SOIC, 0.295 inch (7.50 mm) width
Device Type Dual instrumentation amplifier
Number of Channels 2 channels
Gain 10 or 100 V/V
Listed Gain-Bandwidth Product 200 kHz
Power Class Low power
Input Architecture Differential
Mounting Type Surface mount

Wichtigste Unterscheidungsmerkmale

  • Two instrumentation-amplifier channels in one package (vs. Single-channel instrumentation amplifiers)
  • Two confirmed gain settings (vs. Fixed-gain instrumentation amplifiers)
  • Low-power dual analog front end (vs. Discrete three-op-amp instrumentation amplifier circuits)

Designhinweise

Route each differential input pair as a short, tightly coupled trace pair and minimize the area enclosed by the two conductors. This reduces pickup from switching nodes and prevents common-mode interference from converting into differential error. Keep the two channels' input networks physically similar when they measure matched sensors, and place any input protection or filtering components close to the amplifier pins.

Assign every net from the pin-description table in the Texas Instruments INA2141 datasheet rather than relying on the 16-pin SOIC outline alone. Two amplifier channels share package-level resources and must not be treated as two unrelated single-channel parts. Verify the recommended land pattern, solder-reflow profile, and exposed-thermal requirements against the manufacturer's package drawing before releasing artwork.

Choose the gain according to both signal amplitude and required bandwidth. Estimated from the listed 200 kHz gain-bandwidth product, gain 10 corresponds to approximately 20 kHz and gain 100 to approximately 2 kHz. These are design estimates rather than guaranteed ac specifications; confirm the datasheet bandwidth, settling-time, and gain-error curves for the operating mode selected in the schematic.

Do not select the excitation or signal common-mode voltage without checking the INA2141UA input common-mode range and supply limits. A bridge or sensor output can remain well within its own signal range while exceeding the amplifier's permissible input window. Also confirm output swing at the required gain, since a gain-setting network and reference configuration can change the usable output range.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The Texas Instruments product page confirms INA2141 as an active product but does not provide the compliance values required for this field. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations on the current manufacturer product documentation.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

INA2141UA INA2141UA datasheet INA2141UA datasheet pdf INA2141UA pinout INA2141UA equivalent INA2141UA replacement INA2141UA cross reference INA2141UA price INA2141UA stock Texas Instruments INA2141UA INA2141UA 16 SOIC INA2141UA gain 10 100

Verwandte Bauteile & Begriffe

Texas Instruments INA2141UA INA2141 dual instrumentation amplifier instrumentation amplifier operational amplifier IC analog signal-chain IC semiconductor differential input common-mode rejection common-mode voltage gain of 10 gain of 100 200 kHz gain-bandwidth product 16-pin SOIC SOIC package family surface-mount package bridge sensor strain gauge current shunt battery monitoring industrial instrumentation low-power analog front end Texas Instruments INA2141 product page
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen