INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI
N.º de pieza: INA2141UA ✓ ActivoINA2141UA Descripción general
An instrumentation amplifier is a precision analog amplifier optimized for differential signals. Its internal architecture amplifies the voltage difference between two inputs while rejecting common-mode noise, which is important when a sensor output is small relative to the surrounding electrical environment. The INA2141 belongs to the wider category of operational amplifier ICs and analog signal-chain devices used to condition, scale, and route sensor signals before conversion or control.
Key confirmed features include dual amplifier channels, low-power operation, selectable gains of 10 and 100, a 200 kHz listed bandwidth figure, and a 16-pin SOIC package. The dual configuration allows one device to serve two independent analog channels, reducing component count when the board area is constrained. The two gain settings also support different sensor ranges without changing the overall signal-chain architecture.
The device uses a three-operational-amplifier instrumentation-amplifier approach to provide differential input handling and high common-mode rejection. Exact input common-mode range, output swing, supply range, input bias current, offset voltage, noise density, and quiescent current should be confirmed in the manufacturer datasheet before the circuit is released for production.
Typical uses include bridge-sensor front ends, pressure and force measurement, current-shunt monitoring, battery-cell sensing, and industrial instrumentation. The dual-channel arrangement is particularly useful when two sensors must be measured under similar electrical conditions, while the 200 kHz gain-bandwidth figure supports signal bandwidths appropriate for many slow-to-moderate industrial sensing tasks.
Design layouts should provide short, symmetric input traces, a stable reference configuration, and careful grounding around the analog inputs. Because the INA2141UA operates in a differential measurement environment, input filtering, protection, and connector grounding determine whether the amplifier sees the intended signal or external interference.
This page consolidates the confirmed ordering information, package details, functional attributes, application fit, and replacement considerations. It also identifies the technical parameters that should be checked in the manufacturer datasheet before schematic sign-off, helping engineers move from part selection to a validated analog front-end design.
Alternativas directas para INA2141UA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasINA2141UA Valores máximos y características eléctricas
| Device Type | Dual instrumentation amplifier |
| Number of Channels | 2 channels |
| Gain | 10 or 100 V/V |
| Listed Gain-Bandwidth Product | 200 kHz |
| Supply Type | Low power |
| Encapsulado | 16-pin SOIC, 0.295 inch (7.50 mm) width |
| Tipo de montaje | Surface mount |
| Input Type | Differential |
Guía de configuración de pines de INA2141UA 16-pin soic, 0.295 inch (7.50 mm) width
Configuración de pines para INA2141UA (encapsulado 16-pin soic, 0.295 inch (7.50 mm) width). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para INA2141UA.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
INA2141UA es adecuado para 6 aplicacións: Bridge Sensor Measurement, Current Shunt Amplification, Pressure and Force Transducers, Battery Cell Monitoring, Industrial Process Sensing, Precision Instrumentation Signal Conditioning.
Bridge Sensor Measurement
The INA2141UA suits Wheatstone-bridge front ends because each channel amplifies the differential voltage generated by a small change in bridge balance while the two inputs share a larger excitation-related voltage. The confirmed gain settings of 10 and 100 let the same analog front end support sensors with different sensitivities. Use the 16-pin SOIC device when two bridge channels must fit in a compact board area, and verify the bridge excitation voltage against the amplifier input common-mode range before layout release.
Current Shunt Amplification
A low-ohm current shunt produces a small differential voltage proportional to the monitored current, and the INA2141UA is suited to amplifying that voltage without adding a separate differential amplifier stage. Gain of 10 offers a lower-noise route for larger shunt drops, while gain of 100 increases sensitivity for smaller drops. Place the shunt close to the amplifier inputs, route the pair symmetrically, and confirm the maximum input common-mode voltage for the highest shunt current in the design.
Pressure and Force Transducers
Piezoresistive pressure cells and strain-gauge force sensors commonly deliver a small differential output around a substantial common-mode bias. The differential input architecture of the INA2141UA is appropriate for conditioning these outputs, and the dual 16-SOIC package can serve two sensors under similar mechanical conditions. Confirm the selected gain against sensor sensitivity, then check offset, bias current, and common-mode rejection requirements in the manufacturer datasheet.
Battery Cell Monitoring
Battery-management systems often use instrumentation amplifiers to measure small differential cell voltages with a high common-mode potential relative to ground. The INA2141UA's dual-channel configuration can process two monitored inputs while its gain settings of 10 or 100 provide useful scaling options. Verify the complete battery-pack voltage against the device supply rating, keep the input pair short, and confirm that the reference configuration permits accurate midpoint measurement.
Industrial Process Sensing
Temperature, level, and process-control sensors can present low-level differential outputs that must be amplified before an ADC or controller samples them. The INA2141UA combines two low-power instrumentation-amplifier channels in a 16-pin SOIC package, reducing board area in multi-channel industrial equipment. The listed 200 kHz gain-bandwidth product supports moderate-bandwidth process signals, while the selected gain determines the practical closed-loop bandwidth and should be checked against required settling time.
Precision Instrumentation Signal Conditioning
Laboratory and test instruments frequently need to reject noise shared by a pair of sensor lines while amplifying a small differential command or measurement. The INA2141UA provides a matched dual-channel implementation in a 16-pin SOIC package, and each channel can operate at gain 10 or 100. Use matched input filtering and solid grounding to preserve differential accuracy, and confirm the output swing and settling behavior needed by the measurement acquisition chain.
Datos de referencia de ingeniería para INA2141UA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Texas Instruments |
| Package | 16-pin SOIC, 0.295 inch (7.50 mm) width |
| Device Type | Dual instrumentation amplifier |
| Number of Channels | 2 channels |
| Gain | 10 or 100 V/V |
| Listed Gain-Bandwidth Product | 200 kHz |
| Power Class | Low power |
| Input Architecture | Differential |
| Mounting Type | Surface mount |
Diferenciadores clave
- Two instrumentation-amplifier channels in one package (frente a Single-channel instrumentation amplifiers)
- Two confirmed gain settings (frente a Fixed-gain instrumentation amplifiers)
- Low-power dual analog front end (frente a Discrete three-op-amp instrumentation amplifier circuits)
Notas de diseño
Route each differential input pair as a short, tightly coupled trace pair and minimize the area enclosed by the two conductors. This reduces pickup from switching nodes and prevents common-mode interference from converting into differential error. Keep the two channels' input networks physically similar when they measure matched sensors, and place any input protection or filtering components close to the amplifier pins.
Assign every net from the pin-description table in the Texas Instruments INA2141 datasheet rather than relying on the 16-pin SOIC outline alone. Two amplifier channels share package-level resources and must not be treated as two unrelated single-channel parts. Verify the recommended land pattern, solder-reflow profile, and exposed-thermal requirements against the manufacturer's package drawing before releasing artwork.
Choose the gain according to both signal amplitude and required bandwidth. Estimated from the listed 200 kHz gain-bandwidth product, gain 10 corresponds to approximately 20 kHz and gain 100 to approximately 2 kHz. These are design estimates rather than guaranteed ac specifications; confirm the datasheet bandwidth, settling-time, and gain-error curves for the operating mode selected in the schematic.
Do not select the excitation or signal common-mode voltage without checking the INA2141UA input common-mode range and supply limits. A bridge or sensor output can remain well within its own signal range while exceeding the amplifier's permissible input window. Also confirm output swing at the required gain, since a gain-setting network and reference configuration can change the usable output range.
Información de cumplimiento
The Texas Instruments product page confirms INA2141 as an active product but does not provide the compliance values required for this field. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations on the current manufacturer product documentation.