Renesas Electronics

ISL81485IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas

Teilenummer: ISL81485IB ✗ Abgekündigt
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

ISL81485IB Übersicht

Renesas ISL81485IB is a single-channel, half-duplex RS-485/RS-422 line transceiver designed for 5 V operation with a maximum signaling rate of 30 Mbps. The device is manufactured in an 8-pin SOIC package and uses BiCMOS circuit technology. Its balanced differential interface supports bidirectional data transfer between systems connected with twisted-pair cabling, making it suitable for industrial communication, instrumentation, and data-acquisition equipment.

A line transceiver converts logic-level signals into balanced differential signals for transmission over cable, while simultaneously receiving and converting differential cable signals into CMOS-compatible logic. The RS-485/RS-422 interface category combines differential signaling with high noise immunity and common-mode rejection. These characteristics make the ISL81485IB useful where communication distance, ground-potential differences, or electrically noisy surroundings can degrade single-ended digital interconnections.

The ISL81485IB provides one transceiver, allowing a single interface to both transmit and receive. Its half-duplex configuration is appropriate for bus architectures in which a shared pair of conductors carries data in only one direction at a time. The manufacturer identifies the device as a 5 V, 30 Mbps RS-485/RS-422 transceiver and notes that its larger output voltage supports high-speed applications. It also specifies the circuit with a 10% tolerance capability, although the exact associated parameter requires confirmation in the manufacturer datasheet.

BiCMOS implementation combines bipolar and CMOS characteristics within the integrated circuit. In a balanced transceiver, this can support relatively high data rates while maintaining low-power operation compared with older line-driver technologies. The 8-pin SOIC package also provides a conventional surface-mount footprint for industrial-control and communication equipment. Because a line transceiver interfaces between digital logic and external cabling, correct termination, biasing, grounding, and signal-integrity layout are as important as the nominal data rate.

Typical uses for the ISL81485IB include industrial control networks, factory automation links, remote sensor and actuator connections, laboratory instrumentation, and embedded equipment communicating over balanced cabling. Its 30 Mbps capability is useful for shorter, controlled interconnects or legacy high-speed links where long-distance cabling would require careful attenuation and topology analysis. The device may also be used in RS-422 point-to-point systems when the system architecture supports the transceiver's shared bidirectional interface arrangement.

A critical design consideration is that RS-485 and RS-422 interfaces are not automatically interchangeable at the network level. Cable length, topology, termination, idle state, and the number of connected drivers influence the correct implementation. Review the device's drive strength, receiver thresholds, enable behavior, and supply requirements in the manufacturer datasheet before assigning pins or selecting external components.

This product page combines the confirmed operating characteristics, package information, sourcing guidance, and design considerations for the ISL81485IB. It also identifies the fields that require verification from the complete Renesas datasheet, helping engineers evaluate the transceiver without confusing electrical compatibility with guaranteed network interoperability.

Drop-in-Alternativen für ISL81485IB – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

ISL81485IB Technische Daten

Product Type RS-485/RS-422 line transceiver
Transceiver Count 1 transceiver
Duplex Mode Half-duplex
Versorgungsspannung 5 V
Maximum Data Rate 30 Mbps
Interface Standards RS-485 and RS-422
Logic Technology BiCMOS
Gehäuse 8-pin SOIC
Montageart Surface mount
Transmission Line Tolerance 10% tolerance capability

ISL81485IB 8-pin soic Pinbelegungsleitfaden

Pinbelegung für ISL81485IB (8-pin soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für ISL81485IB im 8-pin soic-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ISL81485IB.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ISL81485IB ist geeignet für 6 Anwendungs: Industrial Automation Bus Interface, Factory Automation Equipment, Instrumentation and Test Equipment, Remote Sensor and Actuator Networking, Embedded Communication Port, Point-to-Point RS-422 Link.

🏭

Industrial Automation Bus Interface

The ISL81485IB fits legacy industrial-control networks that require a 5 V balanced interface capable of 30 Mbps signaling. It can connect a controller or programmable controller to remote drives, sensors, or I/O modules using RS-485 or RS-422 wiring. The single half-duplex transceiver allows one pair to support both command transmission and response reception, provided the bus controller manages direction switching correctly. Its BiCMOS implementation and 30 Mbps capability suit short, controlled cabinet links where interference, topology, and termination are carefully managed.

🏭

Factory Automation Equipment

The ISL81485IB is applicable to factory automation controllers, condition-monitoring equipment, and production-line interfaces that exchange data over balanced cable. Its 30 Mbps maximum rate provides ample margin for short machine-to-machine links, while differential signaling improves noise immunity compared with ordinary single-ended interconnects. The 8-pin SOIC package supports conventional industrial PCB assembly. Designers should still verify common-mode limits, driver loading, enable timing, and isolation requirements because those parameters determine reliable operation on multi-node RS-485 networks.

🔧

Instrumentation and Test Equipment

The ISL81485IB can interface laboratory instruments, test fixtures, and measurement systems with external computers or data-acquisition units. A 5 V supply and 30 Mbps operation align with many established control and communication boards, while the balanced RS-485/RS-422 interface reduces susceptibility to ground-offset noise. In bench systems, the link length is normally short enough to focus on signal integrity and connector compatibility. Use controlled-impedance routing, proper pair geometry, and manufacturer-recommended termination to avoid reflections or receiver-threshold errors.

🧩

Remote Sensor and Actuator Networking

The ISL81485IB suits distributed sensing or actuator systems where a field device must communicate over a balanced cable to a central controller. The 30 Mbps capability supports high-rate telemetry over short runs, and the differential interface helps maintain data integrity where the sensor and controller share different ground potentials. Because the device is half-duplex, the system must define turnaround timing and prevent simultaneous transmission from multiple drivers. External protection may also be required when field cables connect to external connectors.

⚡

Embedded Communication Port

The ISL81485IB can add a balanced communication port to an embedded controller or legacy interface card that already operates from 5 V. Connecting a microcontroller UART through the transceiver's logic-side signals creates a physical layer for an RS-485 or RS-422 link without using a separate line-driver package. Firmware must control transmit enable and bus turnaround, while the hardware must provide the proper termination and fail-safe network. This approach is especially useful when preserving an existing 8-pin SOIC board outline and component ecosystem.

🌐

Point-to-Point RS-422 Link

The ISL81485IB can support a point-to-point RS-422 connection between two systems that require balanced signaling and a 5 V interface supply. Its 30 Mbps data rate makes it appropriate for short-distance, high-speed links where cable attenuation remains manageable. The half-duplex arrangement still requires an agreed direction-control method between the endpoints. Confirm the exact receiver thresholds, driver output voltage, enable polarity, and supply sequencing from the datasheet before treating the RS-422 wiring as production-ready.

What is the ISL81485IB?
The ISL81485IB is a single-channel, half-duplex RS-485/RS-422 line transceiver operating from a 5 V supply. According to the Renesas product page, it uses BiCMOS technology and supports data rates up to 30 Mbps in an 8-pin SOIC package. It combines one balanced transmitter and receiver for communications over twisted-pair cabling.
What is the maximum data rate of the ISL81485IB?
The ISL81485IB supports a maximum signaling rate of 30 Mbps. This figure is confirmed by the Renesas product page and the manufacturer datasheet description. Actual link performance also depends on cable length, topology, termination, transceiver loading, connector design, and the integrity of the PCB signal path.
What interface standards does the ISL81485IB support?
The ISL81485IB supports both RS-485 and RS-422 balanced communication standards. Renesas describes it as a single BiCMOS transceiver intended for 5 V operation. These interfaces use differential signaling, but their allowable topology and system behavior differ, so network configuration must be selected independently of the IC package.
Is the ISL81485IB half-duplex or full-duplex?
The ISL81485IB is a half-duplex transceiver. According to the Renesas product page, it contains one transceiver capable of transmitting and receiving over the same balanced interface. A system requiring simultaneous transmission and reception should use separate channels rather than assuming that this device provides full-duplex operation.
Where can I download the ISL81485IB datasheet?
The official ISL81485IB datasheet is available through the Renesas product page at https://www.renesas.com/en/products/isl81485/part-details/isl81485ib. Use the manufacturer PDF for the complete pin-description table, electrical characteristics, timing diagrams, recommended operating conditions, and application circuit details before finalizing a PCB design.
Where can I find the ISL81485IB pinout?
The ISL81485IB pinout is contained in the pin-description table of the Renesas manufacturer datasheet. The package is an 8-pin SOIC, but a complete pin assignment should not be inferred from the package outline alone. Verify driver inputs, receiver outputs, enables, supply pins, and ground connections against the exact ISL81485IB pin table.
ISL81485IB vs. a typical RS-485 transceiver — which is better for high-speed links?
The ISL81485IB is best considered when a legacy system specifically requires its 5 V supply, 30 Mbps capability, RS-485/RS-422 functionality, and 8-pin SOIC footprint. A modern transceiver may offer lower supply voltage, lower power consumption, enhanced failsafe behavior, or wider common-mode range. Confirm every electrical and timing requirement rather than comparing only the maximum data rate.
When should I choose the ISL81485IB over another RS-485 transceiver?
Choose the ISL81485IB when the existing circuit requires a 5 V single transceiver with 30 Mbps operation and an 8-pin SOIC footprint. Its BiCMOS implementation and combined RS-485/RS-422 capability can simplify compatibility with established balanced-interface equipment. For new battery-powered or automotive designs, compare modern alternatives for voltage, power, protection, and lifecycle requirements.
Is the ISL81485IB suitable for industrial automation systems?
The ISL81485IB is suitable for many industrial automation links because it provides a 5 V RS-485/RS-422 differential interface at rates up to 30 Mbps. Suitability depends on the cable length, network topology, termination strategy, grounding method, isolation requirement, and electromagnetic environment. Industrial use may also require a lifecycle and qualification review.
What can replace the ISL81485IB?
A valid replacement must use the same 8-pin SOIC footprint, preserve pin-to-pin signal assignments, and meet the required 5 V supply, RS-485/RS-422 thresholds, output amplitude, and 30 Mbps timing. Package similarity alone does not establish compatibility. Check enable polarity, receiver fail-safe behavior, bus loading, thermal limits, and transceiver enable timing for each proposed substitute.
Is the ISL81485IB still supported for new designs?
Renesas states that support is limited to customers who have already adopted the ISL81485 product family. This indicates restricted lifecycle support, so engineers should confirm current status and availability with the manufacturer before starting a new production design. Existing implementations may still be appropriate when they depend on the established electrical and package configuration.
How should I design the RS-485 PCB layout for the ISL81485IB?
Place the transceiver close to its connector or cable interface, keep the balanced pair closely coupled, and route the pair away from clocks, switching nodes, and other high-current paths. Provide the termination and fail-safe network values specified by the manufacturer. Use a continuous ground reference and connect decoupling capacitors directly to the supply and ground pins.
How much decoupling does the ISL81485IB require?
The exact capacitor values should be taken from the manufacturer's typical application circuit and power-supply recommendations. Place the required high-frequency bypass capacitor immediately across the 5 V and ground pins, with additional bulk capacitance placed according to the supply network and cable-transients environment. Do not use a remote capacitor location that leaves a long high-impedance supply trace.
What are the key specifications of the ISL81485IB that engineers should know?
The ISL81485IB is a 5 V, single-channel, half-duplex BiCMOS transceiver supporting RS-485 and RS-422 at up to 30 Mbps in an 8-pin SOIC package. Its confirmed specifications include one transceiver, 30 Mbps maximum signaling rate, 5 V supply operation, balanced differential signaling, and 10% tolerance capability.
Where can I buy the ISL81485IB and what is its lead time?
Use the Request a Quote form on this page to request ISL81485IB availability, current commercial terms, and lead time. Because Renesas limits support for customers that have already adopted the product, confirm lifecycle status and manufacturing continuity before committing to a new build. The form avoids static pricing information that may change independently of current inventory.
What is the best Renesas equivalent for the ISL81485IB?
The ISL81485IB-T appears in the cross-reference records, but it represents an ordering or packaging designation rather than a distinct functional equivalent. Before using it as a substitution, verify that its exact ordering code, package, pinout, electrical ratings, and tape-and-reel handling match the assembly requirement. Do not treat a suffix change alone as proof of drop-in compatibility.

Technische Referenzdaten für ISL81485IB – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ISL81485IB for a legacy or established design that specifically requires a 5 V, single-channel, half-duplex RS-485/RS-422 transceiver with 30 Mbps operation and an 8-pin SOIC footprint. It is particularly relevant when maintaining equipment designed around the original Intersil/Renesas interface and when a lifecycle continuity review supports continued adoption. Before selecting it for a new design, compare modern transceivers for lower power, wider common-mode range, enhanced failsafe behavior, integrated protection, and current lifecycle status. Any proposed replacement must be checked for pin-to-pin compatibility rather than package similarity alone. The correct decision depends on bus topology, cable length, grounding, protection, enable timing, and production availability.

Vergleich mit Alternativen

Parameter Dieses Produkt
Brand Renesas Electronics
Package 8-pin SOIC
Transceiver Count 1
Duplex Mode Half-duplex
Supply Voltage 5 V
Maximum Data Rate 30 Mbps
Interface Standards RS-485 and RS-422
Logic Technology BiCMOS
Transmission Line Tolerance 10% tolerance capability

Designhinweise

Place the ISL81485IB close to the board connector or cable interface. Route the differential pair as a closely coupled pair with continuous reference to the ground plane, and keep the pair away from switching power nodes, high-speed clocks, and inductors. Place termination components near the transceiver or connector according to the selected bus topology so that stubs remain electrically short.

Connect the 5 V supply and ground pins directly to a low-impedance plane, and place the manufacturer's recommended bypass capacitor immediately beside those pins. Keep the capacitor-return path short and avoid routing supply current through the digital ground region. If the transceiver is connected to an external cable, evaluate surge and transient requirements separately because the logic-side decoupling capacitor does not replace a suitable bus protection network.

Do not treat equal package dimensions as proof of interchangeability. A substitute must preserve the exact pin assignments, enable polarity, receiver thresholds, output amplitude, timing, and supply requirements of the ISL81485IB. In particular, verify half-duplex turnaround timing and ensure only one driver asserts onto an RS-485 segment at a time.

Confirm termination and fail-safe biasing using the complete network topology rather than applying a fixed resistor set to every installation. Stubs, excessive cable length, and incorrect idle bias can reduce the usable data rate below the device's 30 Mbps maximum. Measure the differential waveform at the receiver under worst-case loading before releasing a high-speed production design.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available Renesas product information does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this exact ordering code.

Daten verifiziert am: 2026-11-15 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

ISL81485IB datasheet ISL81485IB pinout ISL81485IB datasheet pdf ISL81485IB equivalent ISL81485IB replacement ISL81485IB cross reference Renesas ISL81485IB ISL81485IB 8-SOIC ISL81485IB 30Mbps RS-485 ISL81485IB price ISL81485IB stock ISL81485IB RS-422 application circuit

Verwandte Bauteile & Begriffe

Renesas Electronics Intersil ISL81485IB ISL81485IB-T RS-485 RS-422 line transceiver half-duplex transceiver balanced differential signaling BiCMOS CMOS bipolar technology 5 V power supply 30 Mbps data rate 8-pin SOIC SOIC package family surface-mount package industrial automation factory automation instrumentation common-mode rejection termination resistor bus topology
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen