ISL81485IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas
料号: ISL81485IB ✗ 停产ISL81485IB 概述
A line transceiver converts logic-level signals into balanced differential signals for transmission over cable, while simultaneously receiving and converting differential cable signals into CMOS-compatible logic. The RS-485/RS-422 interface category combines differential signaling with high noise immunity and common-mode rejection. These characteristics make the ISL81485IB useful where communication distance, ground-potential differences, or electrically noisy surroundings can degrade single-ended digital interconnections.
The ISL81485IB provides one transceiver, allowing a single interface to both transmit and receive. Its half-duplex configuration is appropriate for bus architectures in which a shared pair of conductors carries data in only one direction at a time. The manufacturer identifies the device as a 5 V, 30 Mbps RS-485/RS-422 transceiver and notes that its larger output voltage supports high-speed applications. It also specifies the circuit with a 10% tolerance capability, although the exact associated parameter requires confirmation in the manufacturer datasheet.
BiCMOS implementation combines bipolar and CMOS characteristics within the integrated circuit. In a balanced transceiver, this can support relatively high data rates while maintaining low-power operation compared with older line-driver technologies. The 8-pin SOIC package also provides a conventional surface-mount footprint for industrial-control and communication equipment. Because a line transceiver interfaces between digital logic and external cabling, correct termination, biasing, grounding, and signal-integrity layout are as important as the nominal data rate.
Typical uses for the ISL81485IB include industrial control networks, factory automation links, remote sensor and actuator connections, laboratory instrumentation, and embedded equipment communicating over balanced cabling. Its 30 Mbps capability is useful for shorter, controlled interconnects or legacy high-speed links where long-distance cabling would require careful attenuation and topology analysis. The device may also be used in RS-422 point-to-point systems when the system architecture supports the transceiver's shared bidirectional interface arrangement.
A critical design consideration is that RS-485 and RS-422 interfaces are not automatically interchangeable at the network level. Cable length, topology, termination, idle state, and the number of connected drivers influence the correct implementation. Review the device's drive strength, receiver thresholds, enable behavior, and supply requirements in the manufacturer datasheet before assigning pins or selecting external components.
This product page combines the confirmed operating characteristics, package information, sourcing guidance, and design considerations for the ISL81485IB. It also identifies the fields that require verification from the complete Renesas datasheet, helping engineers evaluate the transceiver without confusing electrical compatibility with guaranteed network interoperability.
直接替换替代料: ISL81485IB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料ISL81485IB 规格参数
| Product Type | RS-485/RS-422 line transceiver |
| Transceiver Count | 1 transceiver |
| Duplex Mode | Half-duplex |
| 电源电压 | 5 V |
| Maximum Data Rate | 30 Mbps |
| Interface Standards | RS-485 and RS-422 |
| Logic Technology | BiCMOS |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Transmission Line Tolerance | 10% tolerance capability |
ISL81485IB 8-pin soic 引脚配置指南
ISL81485IB(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ISL81485IB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ISL81485IB 适用于 6 应用s: Industrial Automation Bus Interface, Factory Automation Equipment, Instrumentation and Test Equipment, Remote Sensor and Actuator Networking, Embedded Communication Port, Point-to-Point RS-422 Link.
Industrial Automation Bus Interface
The ISL81485IB fits legacy industrial-control networks that require a 5 V balanced interface capable of 30 Mbps signaling. It can connect a controller or programmable controller to remote drives, sensors, or I/O modules using RS-485 or RS-422 wiring. The single half-duplex transceiver allows one pair to support both command transmission and response reception, provided the bus controller manages direction switching correctly. Its BiCMOS implementation and 30 Mbps capability suit short, controlled cabinet links where interference, topology, and termination are carefully managed.
Factory Automation Equipment
The ISL81485IB is applicable to factory automation controllers, condition-monitoring equipment, and production-line interfaces that exchange data over balanced cable. Its 30 Mbps maximum rate provides ample margin for short machine-to-machine links, while differential signaling improves noise immunity compared with ordinary single-ended interconnects. The 8-pin SOIC package supports conventional industrial PCB assembly. Designers should still verify common-mode limits, driver loading, enable timing, and isolation requirements because those parameters determine reliable operation on multi-node RS-485 networks.
Instrumentation and Test Equipment
The ISL81485IB can interface laboratory instruments, test fixtures, and measurement systems with external computers or data-acquisition units. A 5 V supply and 30 Mbps operation align with many established control and communication boards, while the balanced RS-485/RS-422 interface reduces susceptibility to ground-offset noise. In bench systems, the link length is normally short enough to focus on signal integrity and connector compatibility. Use controlled-impedance routing, proper pair geometry, and manufacturer-recommended termination to avoid reflections or receiver-threshold errors.
Remote Sensor and Actuator Networking
The ISL81485IB suits distributed sensing or actuator systems where a field device must communicate over a balanced cable to a central controller. The 30 Mbps capability supports high-rate telemetry over short runs, and the differential interface helps maintain data integrity where the sensor and controller share different ground potentials. Because the device is half-duplex, the system must define turnaround timing and prevent simultaneous transmission from multiple drivers. External protection may also be required when field cables connect to external connectors.
Embedded Communication Port
The ISL81485IB can add a balanced communication port to an embedded controller or legacy interface card that already operates from 5 V. Connecting a microcontroller UART through the transceiver's logic-side signals creates a physical layer for an RS-485 or RS-422 link without using a separate line-driver package. Firmware must control transmit enable and bus turnaround, while the hardware must provide the proper termination and fail-safe network. This approach is especially useful when preserving an existing 8-pin SOIC board outline and component ecosystem.
Point-to-Point RS-422 Link
The ISL81485IB can support a point-to-point RS-422 connection between two systems that require balanced signaling and a 5 V interface supply. Its 30 Mbps data rate makes it appropriate for short-distance, high-speed links where cable attenuation remains manageable. The half-duplex arrangement still requires an agreed direction-control method between the endpoints. Confirm the exact receiver thresholds, driver output voltage, enable polarity, and supply sequencing from the datasheet before treating the RS-422 wiring as production-ready.
工程参考数据: ISL81485IB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Renesas Electronics |
| Package | 8-pin SOIC |
| Transceiver Count | 1 |
| Duplex Mode | Half-duplex |
| Supply Voltage | 5 V |
| Maximum Data Rate | 30 Mbps |
| Interface Standards | RS-485 and RS-422 |
| Logic Technology | BiCMOS |
| Transmission Line Tolerance | 10% tolerance capability |
设计说明
Place the ISL81485IB close to the board connector or cable interface. Route the differential pair as a closely coupled pair with continuous reference to the ground plane, and keep the pair away from switching power nodes, high-speed clocks, and inductors. Place termination components near the transceiver or connector according to the selected bus topology so that stubs remain electrically short.
Connect the 5 V supply and ground pins directly to a low-impedance plane, and place the manufacturer's recommended bypass capacitor immediately beside those pins. Keep the capacitor-return path short and avoid routing supply current through the digital ground region. If the transceiver is connected to an external cable, evaluate surge and transient requirements separately because the logic-side decoupling capacitor does not replace a suitable bus protection network.
Do not treat equal package dimensions as proof of interchangeability. A substitute must preserve the exact pin assignments, enable polarity, receiver thresholds, output amplitude, timing, and supply requirements of the ISL81485IB. In particular, verify half-duplex turnaround timing and ensure only one driver asserts onto an RS-485 segment at a time.
Confirm termination and fail-safe biasing using the complete network topology rather than applying a fixed resistor set to every installation. Stubs, excessive cable length, and incorrect idle bias can reduce the usable data rate below the device's 30 Mbps maximum. Measure the differential waveform at the receiver under worst-case loading before releasing a high-speed production design.
合规信息
The available Renesas product information does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this exact ordering code.