ISL8484IRZ - 0.4 Ohm Dual SPDT Analog Switch | Renesas
Teilenummer: ISL8484IRZ ✓ AktivISL8484IRZ Übersicht
An analog switch is a semiconductor device that routes analog signals between input and output terminals under digital control. The SPDT configuration provides one common terminal and two switched terminals for each circuit, allowing two independent 2:1 selections. In the power-management hierarchy, this dual SPDT switch functions as a low-voltage interface IC for signal routing, test-point multiplexing, and programmable analog paths.
Key electrical characteristics include an on-resistance of 0.29 ohm at +4.3 V, 0.33 ohm at +3.0 V, and 0.55 ohm at +1.8 V. On-resistance matching between channels is 0.06 ohm, while flatness across the signal range is 0.03 ohm. At +4.3 V, turn-on time is 40 ns and turn-off time is 20 ns. The device also provides guaranteed break-before-make behavior.
The dual independent-switch architecture supports simultaneous routing of two analog signals. Its low-voltage supply range makes it suitable for battery-powered instrumentation, portable measurement systems, low-voltage test equipment, and mixed-signal interfaces. The manufacturer identifies the ISL8484 as a pin-compatible replacement for the MAX4684 and MAX4685, with particularly low on-resistance across its stated supply conditions.
Typical circuit roles include selecting between two sensors, connecting a test fixture to a measurement instrument, routing one of two sources into an amplifier, and multiplexing an analog control point. Because the switch operates from a single supply, system designers should confirm that every driven signal remains within the permitted input and output range during switching transitions.
For layout, route the common, switched, and control traces with short analog paths and maintain a continuous ground reference beneath the device. Place bypass capacitance near the supply pin and avoid routing high-impedance signals beneath digital control traces. These practices reduce parasitic distortion and coupling during the 40 ns switching transitions.
This product page combines the manufacturer specifications with a parameter-by-parameter comparison, verified pin-compatible alternatives, and practical routing guidance. Use the Renesas ISL8484 documentation as the authoritative source for the final pin-description table, footprint dimensions, and production release limits before releasing a PCB layout.
Drop-in-Alternativen für ISL8484IRZ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
MAX4684
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX4685
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL8484IRZ Grenzwerte & elektrische Eigenschaften
| Switch Configuration | Dual SPDT |
| Multiplexer Ratio | 2:1 |
| Number of Circuits | 2 circuits |
| Supply Voltage Range | +1.65 V to +4.5 V |
| On-Resistance at +4.3 V | 0.29 ohm |
| On-Resistance at +3.0 V | 0.33 ohm |
| On-Resistance at +1.8 V | 0.55 ohm |
| Distributor Listed On-Resistance | 500 mohm |
| On-Resistance Matching Between Channels | 0.06 ohm |
| On-Resistance Flatness Across Signal Range | 0.03 ohm |
| Turn-On Time at +4.3 V | 40 ns |
| Turn-Off Time at +4.3 V | 20 ns |
| Power Dissipation | <0.45 microwatt |
| ESD HBM Rating | >8 kV |
| Break-Before-Make | Guaranteed |
| Gehäuse | 10-TDFN (3 x 3 mm) |
| Montageart | Surface Mount |
| Termination Finish | 100% matte tin plate with anneal, e3 |
| RoHS-Status | Compliant |
ISL8484IRZ 10-tdfn (3 x 3 mm) Pinbelegungsleitfaden
Pinbelegung für ISL8484IRZ (10-tdfn (3 x 3 mm)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ISL8484IRZ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ISL8484IRZ ist geeignet für 6 Anwendungs: Battery-Powered Sensor Multiplexing, Portable Test and Measurement, Programmable Analog Signal Routing, Low-Voltage Data Acquisition Front Ends, Industrial Control Signal Multiplexing, Audio and Communication Path Selection.
Battery-Powered Sensor Multiplexing
The ISL8484IRZ suits low-voltage sensor-selection circuits because it operates from +1.65 V to +4.5 V and provides two independent 2:1 SPDT paths. Its on-resistance is 0.55 ohm at +1.8 V, 0.33 ohm at +3.0 V, and 0.29 ohm at +4.3 V, allowing one package to route two sensor outputs into a common analog front end. The 40 ns turn-on and 20 ns turn-off times support rapid source selection. Keep switched-node amplitudes within the specified signal range and account for path resistance when sizing amplifier input impedance.
Empfohlen
Portable Test and Measurement
The dual SPDT configuration of the ISL8484IRZ is useful in portable test equipment for connecting two stimulus sources or two measurement paths to shared circuitry. Its low 0.29 ohm on-resistance at +4.3 V minimizes series loss, while 0.03 ohm flatness across the signal range helps preserve amplitude relationships. At +4.3 V, the 40 ns turn-on and 20 ns turn-off characteristics enable rapid range or source changes. Design the surrounding front end to tolerate the selected path's voltage and impedance, and use controlled edge rates where leakage or parasitic capacitance matters.
Empfohlen
Programmable Analog Signal Routing
ISL8484IRZ can implement two independently controlled analog routes in programmable front ends. The 2:1 topology allows either switched terminal to be connected to the common terminal, while the second circuit performs a separate selection. Its +1.65 V minimum supply supports low-energy logic domains, and guaranteed break-before-make behavior helps prevent overlapping switch states. For high-impedance nodes, account for switch leakage and parasitic capacitance, which are not specified in the manufacturer product summary. Place the routing device close to the controlled node and provide a low-impedance reference connection.
Empfohlen
Low-Voltage Data Acquisition Front Ends
The ISL8484IRZ can route two input channels into a compact data-acquisition front end where every stage operates below 4.5 V. Its low on-resistance reduces insertion loss compared with a resistive selector, while 0.06 ohm matching between channels supports balanced channel selection. Fast 40 ns turn-on and 20 ns turn-off operation can shorten acquisition dead time when control timing is accurate. Confirm the maximum signal excursion, off-state isolation, leakage, and bandwidth requirements for the selected acquisition architecture before placing the switch in a precision measurement path.
Empfohlen
Industrial Control Signal Multiplexing
The dual SPDT ISL8484IRZ can multiplex two low-voltage control or diagnostic signals in compact industrial electronics. Its +1.65 V to +4.5 V operating range fits systems using modern low-voltage logic, and the 3 x 3 mm TDFN package preserves board area. Fast switching reduces interruption time, while guaranteed break-before-make behavior provides defined transition sequencing. Route the two analog paths away from motor-control switching nodes, use a solid ground plane, and verify the signal levels during all operating states to avoid transient overstress.
Empfohlen
Audio and Communication Path Selection
ISL8484IRZ can select one of two low-level analog paths in portable audio or communication equipment operating near 1.8 V or 3.0 V. At +1.8 V, its on-resistance is 0.55 ohm, rising to 0.33 ohm at +3.0 V, so path loss should be included in the receiver's gain budget. The 40 ns turn-on and 20 ns turn-off times allow rapid source switching, but the application must also manage click, pop, or transient effects caused by the signal step. Maintain short traces and a continuous return path to limit coupling during transitions.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ISL8484IRZ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX4684 | MAX4685 |
|---|---|---|---|
| Brand | Renesas Electronics | Analog Devices | Analog Devices |
| Package | 10-TDFN (3 x 3 mm) | 10-TDFN (3 x 3 mm) | 10-TDFN (3 x 3 mm) |
| Switch Configuration | Dual SPDT | Dual SPDT | Dual SPDT |
| Multiplexer Ratio | 2:1 | 2:1 | 2:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Pin Compatibility | Reference part | Identified by Renesas as pin-compatible replacement | Identified by Renesas as pin-compatible replacement |
Wichtigste Unterscheidungsmerkmale
- Low on-resistance across the stated supply range (vs. MAX4684)
- Fast complementary switching characteristics (vs. MAX4685)
- Defined transition behavior (vs. MAX4684)
Designhinweise
Place the ISL8484IRZ close to the signal source and destination it selects so that the switched paths remain short. Keep the common-node traces away from digital control and clock lines, and route each control input over a continuous ground reference. The 40 ns turn-on and 20 ns turn-off characteristics can expose parasitic coupling, so minimize loop area around the analog nodes.
Do not treat the +1.65 V to +4.5 V supply range as permission for arbitrary signal amplitudes. Check the maximum switched voltage, control-pin thresholds, and absolute-maximum limits in the manufacturer documentation before applying a signal. Also include the selected path resistance in the system gain calculation, especially for the 0.55 ohm on-resistance condition at +1.8 V.
Decouple the supply connection with the capacitance and placement specified by the Renesas application guidance. Keep the supply loop compact because fast switching current can create voltage disturbance along an extended supply trace. Use the device's guaranteed break-before-make behavior for sequencing, but still provide adequate time between control commands when driving sensitive analog nodes.
Compliance-Informationen
The manufacturer documentation states that the Pb-free plastic package uses special Pb-free materials, 100% matte tin plate, anneal, and an e3 termination finish that is RoHS compliant.