KSZ8842-16MBLI - 2-Port 10/100 Ethernet Switch | Microchip
Teilenummer: KSZ8842-16MBLI ✓ AktivKSZ8842-16MBLI Übersicht
An Ethernet switch is a network-semiconductor device that connects multiple Ethernet nodes through a common switching engine. In the broader hierarchy, the KSZ8842-16MBLI belongs to Ethernet interface controllers, then network interface ICs, interface ICs, and integrated circuits. Unlike a physical-layer-only Ethernet transceiver, this device includes the switching function required to interconnect two 10/100 Ethernet ports.
The KSZ8842-16MBLI is identified as a two-port 10/100 Base-T/TX PHY switch with a parallel interface. Its 8/16-bit bus architecture allows an embedded processor or controller to access registers and status information through a non-PCI interface. This makes it suitable for systems that need two Ethernet ports but do not require a PCI bus controller.
Microchip organizes the KSZ8842 family into PCI and non-PCI CPU-interface versions, with 8/16-bit and 32-bit bus designs available across the family. The “16” designation in KSZ8842-16MBLI identifies the 8/16-bit non-PCI family segment, while “MBL” identifies the 100-LFBGA package option used by this ordering code.
Typical applications include embedded routers, industrial control gateways, industrial automation equipment, networked sensors, set-top equipment, and compact communications controllers. In each case, the two integrated 10/100 ports reduce the need for separate Ethernet switching components while preserving a processor-friendly parallel management interface.
For PCB implementation, treat the 100-LFBGA land pattern and its power, ground, clock, interface, and Ethernet differential pairs as a high-speed mixed-signal layout. Follow the manufacturer's recommended decoupling network, provide a clean 25 MHz reference-clock source, and route each 10/100 Ethernet differential pair as a controlled-impedance pair with minimal stubs.
This page combines the family-level architecture, ordering distinctions, drop-in-replacement constraints, and practical PCB guidance into an engineering-focused selection resource. It also separates electrically compatible family members from package or interface changes that require board-level modification, helping designers avoid confusing a similar orderable code with a true pin-to-pin replacement.
Drop-in-Alternativen für KSZ8842-16MBLI – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernKSZ8842-16MBLI Grenzwerte & elektrische Eigenschaften
| Ethernet Port Count | 2 ports |
| Ethernet Speed | 10/100 Mb/s per port |
| Ethernet Physical Layer | 10/100 Base-T/TX PHY |
| Host Bus Width | 8-bit or 16-bit parallel |
| Host Interface Type | Non-PCI CPU interface |
| Device Function | 2-port Ethernet switch with integrated 10/100 PHY |
| Gehäuse | 100-LFBGA |
| Package Pin Count | 100 pins |
| Manufacturer | Microchip Technology |
KSZ8842-16MBLI 100 pins Pinbelegungsleitfaden
Pinbelegung für KSZ8842-16MBLI (100 pins-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für KSZ8842-16MBLI.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
KSZ8842-16MBLI ist geeignet für 6 Anwendungs: Industrial Ethernet Gateway, Embedded Network Router, Networked Sensor Controller, Set-Top Network Interface, Industrial Automation Module, Secure Network Appliance.
Industrial Ethernet Gateway
The KSZ8842-16MBLI fits an industrial Ethernet gateway that needs two 10/100 Mb/s network connections and a processor-controlled management path. Its integrated 10/100 Base-T/TX PHY functions and 8-bit or 16-bit non-PCI interface allow an embedded controller to configure ports, monitor status, and forward data without a PCI bus. Two switch ports in one 100-LFBGA device can simplify a compact gateway PCB, although isolation, surge protection, and the application’s temperature requirements must be addressed separately.
Empfohlen
Embedded Network Router
The KSZ8842-16MBLI is suitable for an embedded router or communications concentrator with two Fast Ethernet ports. The 10/100 Mb/s switch provides the physical connectivity, while the generic 8-bit or 16-bit parallel interface connects the switch to a host processor for routing-table and port management. Its 100-LFBGA package supports compact designs, but the board designer must follow the manufacturer’s differential-pair, reference-clock, decoupling, and thermal-land recommendations.
Empfohlen
Networked Sensor Controller
A networked sensor controller can use the KSZ8842-16MBLI to connect sensing equipment to both a local network and an upstream controller. The two integrated 10/100 Base-T/TX PHY ports support network participation without requiring two independent physical-layer components, and the non-PCI CPU interface suits small embedded processors. For industrial sensor nodes, add the required line protection and verify that the device’s operating-temperature and supply limits match the installation environment.
Empfohlen
Set-Top Network Interface
The KSZ8842-16MBLI can provide dual 10/100 Mb/s connectivity in a set-top box or network terminal. One port may face an access network while the other connects to a local device, with the integrated switch handling Ethernet frame forwarding. The generic 8-bit or 16-bit host interface enables configuration from an embedded system-on-chip. PCB implementation should maintain controlled impedance on all Ethernet pairs and place the required clock and decoupling networks close to the 100-LFBGA device.
Empfohlen
Industrial Automation Module
The KSZ8842-16MBLI is applicable to compact automation modules requiring two Ethernet ports for controller-to-network and controller-to-service-device connections. Its 10/100 Mb/s capability is appropriate for common industrial Ethernet segments operating at 10 or 100 Mb/s, while the non-PCI parallel interface works with embedded processors that do not use a PCI host bus. The design must still include suitable magnetics, isolation or protection strategy, grounding, and environmental qualification for the target enclosure.
Empfohlen
Secure Network Appliance
The KSZ8842-16MBLI can serve as the two-port Fast Ethernet front end of a compact secure gateway or appliance. The host processor accesses switch functions through the generic 8-bit or 16-bit non-PCI interface, while two integrated PHYs connect internal and external network segments. Because the device includes Ethernet physical-layer and switching functions, security functions such as firewalling and packet inspection remain the responsibility of the host processor. Layout should minimize coupling between digital bus signals and the Ethernet differential pairs.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für KSZ8842-16MBLI – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | KSZ8842-16MQL | KSZ8842-PMQL | KSZ8842-PMBL |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Ethernet Ports | 2 ports | 2 ports | 2 ports | 2 ports |
| Ethernet Speed | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s |
| Host Interface | Generic 8/16-bit non-PCI CPU interface | Generic 8/16-bit non-PCI CPU interface | PCI CPU interface | PCI CPU interface |
| Physical Layer | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY |
| Switching Function | Two-port 10/100 Ethernet switch | Two-port 10/100 Ethernet switch | Two-port 10/100 Ethernet switch | Two-port 10/100 Ethernet switch |
| Drop-In Status | Reference device | Not confirmed; verify package and pinout | Not a drop-in option; PCI interface and PQFP package | Not a drop-in option; PCI interface |
Wichtigste Unterscheidungsmerkmale
- Combines two integrated 10/100 Ethernet ports in one 100-LFBGA device (vs. KSZ8842-PMQL)
- Supports processor architectures without a PCI host bus (vs. KSZ8842-PMBL)
- Combines two 10/100 Base-T/TX PHY functions with switching logic (vs. KSZ8842-16MQL)
Designhinweise
Route each 10/100 Ethernet differential pair as a controlled-impedance pair with symmetric geometry and no unnecessary stubs. Keep the pairs away from clocks, high-speed CPU-bus traces, and switching-power nodes. Place the Ethernet input and output network components at the locations specified by the manufacturer reference design. The 100-LFBGA also requires exact ball assignment and land-pattern verification; never derive the footprint from a visually similar family member.
Use the supply voltage, current limits, and decoupling values listed in the Microchip datasheet DS00003459A. Place the required bulk and high-frequency decoupling capacitors as close as practical to their designated power balls, with a low-impedance ground path and adequate via connectivity beneath the device. Keep analog supply and digital supply return currents separated as far as the reference layout allows to reduce switching noise and ground bounce.
Provide the required reference clock with low jitter and route it away from Ethernet differential pairs and parallel host-bus signals. Account for clock, bus, and reset timing when the host processor initializes the switch. If the processor and Ethernet switch share a board, place series damping or other source-termination measures only after analyzing the actual edge rates and topology; the 8/16-bit bus timing and clock requirements should be checked in the manufacturer documentation.
Do not confuse KSZ8842-16MBLI with KSZ8842-16MBLI-TR, KSZ8842-16MQL, KSZ8842-PMQL, or KSZ8842-PMBL. The suffix changes the shipping option, package, or CPU-interface architecture, and a similar family code is not automatically pin compatible. Before substitution, compare package drawings, every power ball, the reference clock, reset behavior, CPU-bus width, PHY connections, and Ethernet transformer or magnetic-component requirements.
Compliance-Informationen
The LFBGA package designation does not by itself establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals compliance. Confirm these declarations using the current Microchip product declaration or material-compliance documentation.