KSZ9896CTXI-TR - 6-Port Gigabit Ethernet Switch | Microchip (Tape & Reel)
Teilenummer: KSZ9896CTXI-TR ✓ AktivKSZ9896CTXI-TR Übersicht
An Ethernet switch is a network-semiconductor device that receives frames on one port and forwards them to the appropriate destination ports. A managed Layer 2 switch adds configurable port behavior, status monitoring, and traffic control beyond the basic function of an unmanaged switch. The KSZ9896 combines five copper Gigabit Ethernet PHYs with a flexible sixth-port MAC interface, allowing it to serve as the central switching element in industrial, automotive, communications, and embedded Ethernet equipment.
Five of the six ports integrate 10/100/1000 Mbps PHYs, allowing the switch to support gigabit links while retaining 100 Mbps and 10 Mbps compatibility. The sixth port can be configured through GMII, RGMII, MII, or RMII, providing flexibility for connections to another Ethernet controller, FPGA, processor, or network interface. I2C and SPI host interfaces support configuration and status access for embedded systems.
The managed switching architecture operates at Layer 2 and supports the IEEE 802.3 Ethernet functions required by the KSZ9896 family. Integrating five PHYs into the switch reduces the component count of a multi-port network design by eliminating several external PHY devices. The integrated MAC interface provides a configurable path to higher-speed or differently structured network interfaces without requiring a separate switch solely for interface conversion.
Typical uses include industrial Ethernet controllers, automotive in-vehicle networking equipment, industrial gateways, embedded network appliances, and communications equipment with multiple copper ports. The combination of five integrated Gigabit PHYs and one configurable MAC interface is particularly useful when a design requires several local copper links plus a connection to a host processor, FPGA, or additional switching silicon.
PCB implementation requires careful attention to the 128-pin TQFP exposed-pad footprint, high-speed differential routing, and thermal performance. The exposed pad must be connected to the appropriate ground plane with adequate via density, while each Ethernet magnetic interface requires its own carefully terminated network path. Review the manufacturer pin-description table and recommended layout guidance before assigning every power, ground, and signal connection.
This product page combines the manufacturer’s switching capability overview with practical procurement and engineering guidance. It highlights the distinction between the five integrated PHY ports and the configurable sixth MAC port, clarifies interface-selection considerations, and organizes replacement questions around verified package and compatibility requirements rather than treating electrically similar switches as automatic substitutes.
Drop-in-Alternativen für KSZ9896CTXI-TR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit KSZ9896CTXI-TR (gleiche Bauform und Footprint) – abweichend in Package, Integrated PHY Data Rates, Product Type, RoHS Status.
KSZ9896CTXC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →KSZ9897RTXI
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →KSZ9896CTXI-TR Grenzwerte & elektrische Eigenschaften
| Device Type | Managed Layer 2 Ethernet switch |
| Total Port Count | 6 ports |
| Integrated Gigabit Ethernet PHY Ports | 5 ports |
| Configurable MAC Port Count | 1 port |
| Integrated PHY Data Rates | 10/100/1000 Mbps per port |
| Configurable MAC Interface | GMII/RGMII/MII/RMII |
| Management Interfaces | I2C and SPI |
| Ethernet Standard | IEEE 802.3 |
| Network Layer | Layer 2 |
| Switch Architecture | Fully integrated six-port managed switch |
| Gehäuse | 128-pin TQFP with exposed pad, 14 x 14 mm |
| Montageart | Surface mount |
KSZ9896CTXI-TR 128-pin tqfp with exposed pad, 14 x 14 mm Pinbelegungsleitfaden
Pinbelegung für KSZ9896CTXI-TR (128-pin tqfp with exposed pad, 14 x 14 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für KSZ9896CTXI-TR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
KSZ9896CTXI-TR ist geeignet für 6 Anwendungs: Industrial Ethernet Gateway, Automotive In-Vehicle Networking, Embedded Network Appliance, Industrial Security and Surveillance, FPGA-Based Network Processing, Communication Equipment Backplane.
Industrial Ethernet Gateway
The KSZ9896CTXI-TR fits industrial gateways that must aggregate several 10/100/1000 Mbps copper links while communicating with a host processor. Five integrated Gigabit PHYs provide direct device connections, and the sixth GMII/RGMII/MII/RMII port can connect to an embedded controller. I2C and SPI management simplify configuration of port parameters and status monitoring. The principal design benefit is fewer external PHY components and shorter network paths, although each Ethernet channel still requires proper magnetics, impedance-controlled routing, isolation, and surge-protection design for the industrial environment.
Empfohlen
Automotive In-Vehicle Networking
The KSZ9896CTXI-TR can support multi-port Ethernet aggregation in an in-vehicle network when its exact temperature grade and automotive qualification satisfy the platform requirements. Five 10/100/1000 Mbps PHYs support connections to vehicle Ethernet nodes, while the configurable sixth MAC interface links the switching fabric to a vehicle-domain controller, FPGA, or communications processor. I2C and SPI permit a host MCU to initialize and monitor the switch. Design work must include ISO 26262-aware fault analysis, transient protection, grounding, and confirmation that the selected ordering code meets the vehicle program’s qualification requirements.
Empfohlen
Embedded Network Appliance
The KSZ9896CTXI-TR is suitable for embedded appliances that expose several Ethernet ports to cameras, storage systems, or service equipment. Five integrated Gigabit PHYs reduce board area compared with five independent PHY implementations, and the sixth configurable MAC port connects to the appliance’s main processor through RGMII, RMII, MII, or GMII as required. Layer 2 management through I2C or SPI gives the embedded software a path to configure ports and read status. The design must preserve the manufacturer’s differential-pair geometry and provide isolated magnetics or appropriately designed common-mode filtering at every external copper interface.
Empfohlen
Industrial Security and Surveillance
The KSZ9896CTXI-TR supports network consolidation in surveillance systems that combine multiple camera or access-control nodes with a central recording platform. The five integrated Gigabit PHYs can serve local 10/100/1000 Mbps endpoints, while the sixth MAC interface connects to an NVR, edge processor, or FPGA-based imaging subsystem. The managed Layer 2 architecture and I2C/SPI control path permit firmware-driven port configuration and monitoring. Industrial installations should add surge and overvoltage protection at cable entry points, maintain isolated network domains where required, and validate frame-forwarding behavior under sustained multiport traffic.
Empfohlen
FPGA-Based Network Processing
The KSZ9896CTXI-TR can complement FPGA-based packet-processing systems that require several physical Ethernet ports alongside programmable logic. Five integrated PHYs accept copper links directly, and the configurable sixth port can use GMII or RGMII for a wide parallel interface to the FPGA. I2C and SPI simplify software or hardware initialization. This arrangement allows the FPGA to handle filtering, protocol processing, or traffic aggregation without requiring a separate physical switch. Interface timing, clock domains, reference clocks, and the number of available transceiver resources must be checked carefully because the switch and FPGA must be initialized in a defined order.
Empfohlen
Communication Equipment Backplane
The KSZ9896CTXI-TR fits communication equipment that combines multiple access ports with an uplink or fabric connection. The five integrated Gigabit Ethernet PHYs can connect access devices, while GMII, RGMII, MII, or RMII on the sixth port supports a host controller or another switching block. Managed Layer 2 operation helps implement port-aware traffic handling through the I2C or SPI management interface. Equipment designers should budget for electromagnetic-compatibility margins, chassis grounding, cable surge events, and thermal testing with all six ports active, since sustained traffic can increase switching and I/O power dissipation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für KSZ9896CTXI-TR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | KSZ9896CTXC | KSZ9897RTXI |
|---|---|---|---|
| Package | 128-pin TQFP with exposed pad, 14 x 14 mm | 128-pin TQFP with exposed pad | 128-pin TQFP with exposed pad |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Temperature Grade | I-grade ordering suffix | C-grade ordering suffix | R-grade ordering suffix |
| Ordering Code Status | KSZ9896CTXI-TR | KSZ9896CTXC | KSZ9897RTXI |
Wichtigste Unterscheidungsmerkmale
- Five integrated Gigabit PHYs in one switch device (vs. KSZ9896CTXC)
- Configurable sixth-port MAC interface (vs. KSZ9897RTXI)
- Embedded configuration through two serial interfaces (vs. KSZ9896CTXC)
Designhinweise
Use the manufacturer’s recommended-layout section as the controlling reference for the 128-pin TQFP exposed-pad footprint. Connect the exposed pad to the ground plane with a dense via array, provide uninterrupted ground beneath the device, and place bypass capacitors directly at the corresponding supply pins. Route Ethernet differential pairs with matched impedance and controlled spacing, and avoid placing disruptive clocks or switching nodes beneath the high-speed network interfaces.
Treat the fifth integrated PHY and configurable MAC interface as separate high-speed design channels. Follow the manufacturer’s differential-pair length, spacing, isolation, and via-transition guidance, including any prescribed connection through Ethernet magnetics. Verify the sixth-port GMII, RGMII, MII, or RMII configuration against host clocking and signal-direction requirements because each mode changes timing, voltage, and routing constraints.
Estimate total dissipation from the switch core, PHY activity, configured MAC interface, and external supply currents under the worst expected port-loading condition. Compare junction temperature with the manufacturer’s maximum rating, accounting for ambient temperature and PCB thermal resistance. The exposed pad and ground-plane copper are primary heat paths, so thermal-via density and copper continuity should be included in thermal simulation rather than relying only on component placement.
Do not treat similar Ethernet-switch MPNs as drop-in parts without checking every pin and configuration. In particular, verify the ordering suffix, temperature grade, PHY count, sixth-port interface, management pins, clock requirements, strap options, initialization sequence, and exposed-pad connection. Follow the current manufacturer data sheet and errata documents because operational differences and recommended workarounds may apply to production devices.
Compliance-Informationen
Compliance status requires confirmation from the exact ordering code or the manufacturer’s material-declaration documentation.