LAN9303I-ABZJ-TR - 3-Port Ethernet Switch | Microchip
Teilenummer: LAN9303I-ABZJ-TR ✓ AktivLAN9303I-ABZJ-TR Übersicht
An Ethernet switch is a network-layer device that receives Ethernet frames on one port, applies address-based forwarding, and transmits each frame toward the appropriate destination port. The LAN9303 family combines three 10/100 Ethernet ports with switch management and host-interface functions in one low-footprint device. This integration reduces the component count and board area required for embedded Ethernet connectivity while preserving a conventional MII or RMII connection to a host processor.
Key features include three 10/100 ports, integrated 10/100 Base-T and TX PHY functions, support for MII and RMII host interfaces, and an I2C management interface. The 56-pin QFN package measures 8 mm by 8 mm and includes an exposed thermal pad. Tape-and-reel ordering is represented by the -TR suffix. The manufacturer describes the family as a high-performance, small-footprint, fully featured managed switch intended for consumer and embedded electronics with rapid development cycles.
The LAN9303 architecture provides the switching function and physical-layer connectivity needed for embedded equipment, while the host-facing digital interface connects the device to a network-capable processor. MII and RMII support provide options for integrating with processors that use parallel or reduced-width media-independent interfaces. I2C access supports configuration and management tasks in systems where separate GPIO programming or a more complex host interface would be unnecessary.
Typical uses include industrial control panels, factory automation equipment, embedded network gateways, set-top and consumer devices, print systems, and compact communications equipment. A three-port arrangement is useful when one port connects to an upstream network and two ports serve local nodes, or when two devices need direct network connectivity around the switch. The managed-switch feature set also makes the device suitable for embedded designs that require more controlled network behavior than an unmanaged repeater.
Board design must account for the exposed pad, high-speed differential Ethernet pairs, controlled impedance, component placement around PHY sections, and the power requirements of the selected operating mode. Keep the manufacturer-recommended magnetic-interface or magnetics-bypass layout for copper connections, and route each 10/100 Ethernet pair as a controlled-impedance differential pair. The exposed pad should be connected to the appropriate ground plane using the thermal and layout guidance in the manufacturer datasheet.
This page consolidates the device identity, interface roles, package characteristics, sourcing information, comparison points, and practical integration guidance into one engineering-oriented reference. It is designed to help designers distinguish the managed LAN9303I function from unrelated Ethernet controllers and to plan a board implementation before committing to the 56-pin QFN footprint.
Drop-in-Alternativen für LAN9303I-ABZJ-TR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LAN9303I-ABZJ-TR (gleiche Bauform und Footprint) – abweichend in Package, Ethernet Speed, Host Interface, Maximum Data Rate, Product Type.
LAN9313I-NZW-TR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LAN9303I-ABZJ-TR Grenzwerte & elektrische Eigenschaften
| Product Type | 3-port managed 10/100 Ethernet switch |
| Number of Ethernet Ports | 3 ports |
| Supported Ethernet Speeds | 10 Mbps and 100 Mbps |
| Ethernet PHY | Integrated 10/100 Base-T/TX PHY |
| Host Interface | MII/RMII |
| Management Interface | I2C |
| Gehäuse | 56-pin QFN, 8 mm x 8 mm, exposed pad |
| Montageart | Surface mount |
| Orderable Packaging | Tape and reel |
| Maximum Data Rate | 100 Mbps per port |
| Switch Management | Managed Ethernet switch |
LAN9303I-ABZJ-TR 56-pin qfn, 8 mm x 8 mm, exposed pad Pinbelegungsleitfaden
Pinbelegung für LAN9303I-ABZJ-TR (56-pin qfn, 8 mm x 8 mm, exposed pad-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für LAN9303I-ABZJ-TR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LAN9303I-ABZJ-TR ist geeignet für 6 Anwendungs: Industrial Automation Controller, Embedded Network Gateway, Set-Top and Consumer Equipment, Factory Communication Hub, Printer and Imaging Controller, IoT Edge Device.
Industrial Automation Controller
The LAN9303I-ABZJ-TR fits industrial automation controllers that must connect a host processor to multiple 10/100 Ethernet devices while keeping the hardware compact. Its three managed ports can provide one network uplink and two local connections, or connect separate sensors, drives, and service interfaces. The integrated MII/RMII and I2C interfaces reduce the need for discrete Ethernet PHY components, while the 56-QFN package limits board footprint. Design the copper network section around the manufacturer’s magnetic-interface or magnetics-bypass layout, and confirm operating-temperature requirements for the installation environment.
Empfohlen
Embedded Network Gateway
The LAN9303I-ABZJ-TR is well suited to an embedded gateway that must bridge a processor-based control plane to multiple 10/100 networks. One port can face the external network while two ports serve local equipment, or the three ports can support internal network segmentation. At 100 Mbps per port, the switch provides Fast Ethernet throughput for management, configuration, and supervisory traffic. The RMII option can reduce host-side pin count, while I2C management access supports configuration from the same embedded processor.
Empfohlen
Set-Top and Consumer Equipment
The LAN9303I-ABZJ-TR supports set-top boxes and consumer products that require three Fast Ethernet connections without implementing a three-port switch externally. A system can use one port for service-network access and two for local peripherals or media devices. Its managed-switch architecture offers more structured forwarding behavior than a simple repeater, while the 8 mm by 8 mm QFN package conserves board area. Product developers should preserve the recommended Ethernet magnetics placement and separation between each differential pair and other high-speed circuitry.
Empfohlen
Factory Communication Hub
The LAN9303I-ABZJ-TR can form the Ethernet-switching core of a compact factory communication hub for machine controllers, remote I/O, and service equipment. Its three 10/100 ports support a useful topology in which one uplink connects to a plant network and two downstream ports serve field equipment. Managed switching helps organize traffic at the embedded system level, and MII/RMII connectivity allows implementation with different host-controller resources. Copper ports require careful differential-pair routing, controlled impedance, and the manufacturer-prescribed magnetic-component layout.
Empfohlen
Printer and Imaging Controller
The LAN9303I-ABZJ-TR fits printer, scanner, and imaging controllers that need a local Ethernet switch with three Fast Ethernet ports. The ports can connect a host controller to a network uplink and one or two service interfaces, avoiding separate Ethernet switches when board space is constrained. The 56-pin QFN outline supports dense layouts, and the managed switch provides frame-forwarding functionality at the system level. Validate connector magnetics, isolation, return-path design, and thermal performance around the exposed pad before release.
Empfohlen
IoT Edge Device
The LAN9303I-ABZJ-TR is appropriate for an IoT edge device that connects a host processor with sensors, cameras, access-control equipment, and an upstream network. Three 10/100 ports allow a practical combination of infrastructure uplink and two local links without adding three separate Ethernet PHYs. The switch’s MII and RMII options provide flexibility against different processor pin budgets, while I2C enables management access. For low-power edge nodes, evaluate controller sleep requirements and Ethernet link behavior during the intended duty cycle before finalizing the power architecture.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LAN9303I-ABZJ-TR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LAN9313I-NZW-TR |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 56-QFN (8x8) with exposed pad | 56-QFN (8x8) exposed-pad format |
| Product Type | Managed 10/100 Ethernet switch | Managed 10/100 Ethernet switch |
| Ethernet Port Count | 3 ports | 3 ports |
| Supported Speed | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps |
| Integrated PHY Configuration | 10/100 Base-T/TX PHY | Differing integrated-PHY configuration |
| Orderable Packaging | Tape and reel | Tape and reel |
Wichtigste Unterscheidungsmerkmale
- Integrated three-port managed-switch architecture (vs. LAN9313I-NZW-TR)
- Reduced host-side interface option (vs. LAN9313I-NZW-TR)
- Orderable exact 56-QFN tape-and-reel configuration (vs. LAN9313I-NZW-TR)
Designhinweise
Route each 10/100 Ethernet differential pair as a controlled-impedance pair and follow the manufacturer’s magnetics or magnetics-bypass layout exactly. Keep the PHY sections and digital host interface physically separated to reduce radiated emissions and susceptibility. Place termination, common-mode components, and magnetic devices only where prescribed by the reference circuit; arbitrary rearrangement can degrade return loss and cable compatibility.
Treat the 56-QFN exposed pad as both a thermal feature and a required electrical connection. Follow the manufacturer’s land pattern and thermal-via guidance, connect the pad to the designated ground plane, and provide copper area around the package where layout rules allow. Validate junction temperature under the maximum sustained traffic and power-supply conditions rather than assuming the compact package remains cool.
Do not substitute the non-I or non-TR order codes without checking grade, temperature, tray-versus-reel handling, and qualification. Likewise, do not install the LAN9313I-NZW-TR into an existing LAN9303I-ABZJ-TR board solely because both use a 56-QFN outline. Compare every power, clock, reset, management, PHY, and exposed-pad connection before treating it as a drop-in replacement.
Compliance-Informationen
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the manufacturer and distributor information for this order code.