LE910C1-EU - LTE Cat.1 10/5 Mbps Module | Telit Cinterion
Teilenummer: LE910C1-EU ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $22.5 | $22,50 |
| 10 | $20.8 | $208,00 |
| 100 | $18.95 | $1.895,00 |
| 500 | $17.4 | $8.700,00 |
| 1.000 | $15.9 | $15.900,00 |
LE910C1-EU Übersicht
An LTE Cat.1 module is a category of cellular RF transceiver module that provides full-duplex LTE connectivity at modest data rates, sitting within the broader hierarchy of cellular modems: M2M module -> LTE transceiver module -> wireless communication IC. Cat.1 is widely adopted as the migration path from 2G/3G for machine-to-machine devices because it uses the existing LTE network infrastructure without the complexity of Cat-M1 or NB-IoT, while still supporting voice and data.
Key features of the LE910C1-EU include the 10/5 Mbps throughput profile, 3GPP Rel 10 compliance with Rel 12-ready MTC platform features, integrated TCP/IP and UDP/IP protocol stacks, and peripheral connectivity via USB 2.0 HS, UART, and user-definable GPIOs. These characteristics make it well suited to devices that need dependable, always-on wide-area connectivity without a host-side network stack.
The module is part of Telit's flagship xE910 family, whose design-once, use-anywhere philosophy allows LE910C1 variants to serve as pin-to-pin compatible replacements within the same LGA footprint for devices based on earlier 2G, 3G, and LTE family members. The ThreadX RTOS-based firmware platform simplifies application integration, and the LE910Cx family is also offered in Linux-based SKUs for more demanding gateway applications.
Typical applications include smart metering, asset tracking and fleet telematics, industrial gateways and routers, security and alarm panels, and connected point-of-sale terminals, where European-band LTE coverage and low-power, long-lifecycle operation are priorities.
When designing with the LE910C1-EU, budget for a proper RF layout: the antenna is not included, so PCB antenna feed matching, keep-out zones, and supply decoupling follow the Telit LE910C1 Series hardware user's manual guidance for the LGA footprint.
This page synthesizes distributor pricing and availability, drop-in alternatives within the xE910 family, and practical design guidance not consolidated in the manufacturer datasheet.
Drop-in-Alternativen für LE910C1-EU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
LE910C1EU13T131100
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LE910C1EU06T060100
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LE910C1-WWX
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LE910C4-WWX
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LE910C1-NF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ME910G1-EU
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LE910C1-EU Spezifikationen (herstellerveröffentlicht)
| Network Technology | LTE Cat.1 |
| Downlink Data Rate | 10 Mbps |
| Uplink Data Rate | 5 Mbps |
| 3GPP Compliance | Release 10 |
| GNSS Support | Optional quad-constellation: GPS, GLONASS, Galileo, BeiDou, QZSS |
| Package Type | LGA (land grid array), surface mount |
| Montageart | Surface Mount |
| Antenna | Not included (external antenna interface) |
| Host Interfaces | USB 2.0 HS, UART, user-definable GPIOs |
| Protocol Stacks | Integrated TCP/IP and UDP/IP |
| Firmware Platform | ThreadX RTOS (LE910Cx ThreadX series) |
| Region Variant | EU (European LTE bands) |
| Ordering Code (T141100 variant) | LE910C1EU14T141100 |
| Telit Internal Code (T141100) | 25.21.224 |
| Telit Internal Code (T131100) | 25.21.223 |
LE910C1-EU Schnittstellen & Anschlüsse
Für LE910C1-EU ist keine vom Hersteller veröffentlichte Schnittstellenliste verfügbar. Details zu Anschlüssen und Headern finden Sie in der Herstellerdokumentation.
Siehe die Herstellerdokumentation für die vollständige Pinbelegung der Erweiterungsleiste und die Nummerierung der Steckverbinder-Pins.
Typische Anwendungen
LE910C1-EU ist geeignet für 6 Anwendungs: Smart Metering, Asset Tracking and Fleet Telematics, Industrial Gateways and Routers, Security and Alarm Panels, Connected Point-of-Sale Terminals, IoT Sensor Nodes and Remote Monitoring.
Smart Metering
The LE910C1-EU fits smart electricity, gas, and water metering because LTE Cat.1's 10/5 Mbps profile comfortably handles metering telemetry, load-profile uploads, and demand-response messages without the cost and power of Cat.4 hardware. As European 2G/3G networks sunset, its 3GPP Rel 10 LTE-only platform provides a long-term network path, and the xE910 pin-to-pin family lets meter vendors swap regional SKUs on one PCB. The module connects to the metering MCU via UART with its integrated TCP/IP stack offloading network handling; the main trade-off versus NB-IoT is higher peak current, so supply design must support Cat.1 bursts.
Empfohlen
Asset Tracking and Fleet Telematics
Asset trackers and telematics units benefit from the LE910C1-EU's combination of LTE Cat.1 data (10 Mbps down / 5 Mbps up - far more than GPS positional reports need) and optional quad-constellation GNSS (GPS, GLONASS, Galileo, BeiDou, QZSS) in a single LGA module, removing a separate GNSS receiver from the BOM. The EU band plan covers European fleet routes, and integrated TCP/IP/UDP stacks let a low-cost host MCU push JSON telemetry over cellular directly. Design consideration: the external antenna interface requires careful RF layout for combined cellular/GNSS antenna feeds per the Telit hardware user's manual.
Empfohlen
Industrial Gateways and Routers
Industrial LTE gateways use the LE910C1-EU as the WAN side, bridging Modbus, CAN, or Ethernet device networks to cloud platforms. The 10/5 Mbps Cat.1 throughput supports aggregated sensor polling and modest OPC-UA traffic, while USB 2.0 HS and UART host interfaces suit both Linux-based gateway SoCs and smaller RTOS controllers; a Linux-open variant of the same LE910Cx family exists for heavier gateway workloads. The Rel 10 platform with Rel 12-ready MTC features supports long-life industrial deployments, and the xE910 LGA footprint allows a Cat.4 LE910C4 drop-in upgrade where bandwidth demands grow.
Empfohlen
Security and Alarm Panels
Alarm and security panels require a dependable cellular path for event reporting and video-verify clips; the LE910C1-EU's always-on LTE Cat.1 link and integrated IP stacks deliver this with AT-command simplicity from the panel MCU. The EU variant matches European monitoring-center deployments, and pin-to-pin compatibility across the xE910 family lets panel manufacturers maintain one PCB across 2G-legacy, LTE Cat.1, and worldwide SKUs - critical for products with 10-year service lives. Designers should implement heartbeat supervision and fall-back dial paths, budgeting for Cat.1 burst currents in the panel's backup-battery sizing calculation.
Empfohlen
Connected Point-of-Sale Terminals
Mobile and countertop payment terminals need encrypted, low-latency transaction connectivity; the LE910C1-EU's 10/5 Mbps LTE Cat.1 link handles TLS-secured payment authorization and receipt traffic readily. Its compact LGA surface-mount package fits handheld enclosures, USB 2.0 HS suits payment SoCs, and the ThreadX-based firmware platform supports secure application hosting. EU band compliance covers European merchant deployments, and optional GNSS enables geo-fenced transaction features. The main design consideration is EMC isolation between the cellular module and sensitive card-reader electronics, addressed with shield cans and the Telit-recommended PCB keep-out layout.
Empfohlen
IoT Sensor Nodes and Remote Monitoring
Environmental monitoring, cold-chain, and utility-infrastructure sensor nodes use the LE910C1-EU where 2G is no longer dependable: Cat.1 provides the bandwidth headroom for periodic bulk data syncs and OTA configuration, while integrated TCP/IP removes host-side stack complexity from resource-constrained MCUs. Compared with NB-IoT, Cat.1 offers far higher throughput and lower latency at the cost of higher peak current, so it suits mains- or solar-powered nodes rather than coin-cell devices. The user-definable GPIOs directly interface sensors or actuators, and the xE910 footprint preserves the upgrade path to LE910C4 or worldwide SKUs without respinning the sensor-node PCB.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LE910C1-EU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LE910C1EU13T131100 | LE910C1-WWX | LE910C4-WWX | ME910G1-EU |
|---|---|---|---|---|---|
| Package | LGA (surface mount) | LGA - same | LGA - same (pin-to-pin xE910) | LGA - same (pin-to-pin xE910) | LGA - same (pin-to-pin xE910) |
| Brand | Telit Cinterion | Telit Cinterion | Telit Cinterion | Telit Cinterion | Telit Cinterion |
| LTE Category | Cat.1 | Cat.1 | Cat.1 | Cat.4 | Cat.M1 / NB-IoT |
| Region / Band Plan | EU | EU | Worldwide | Worldwide | EU |
Wichtigste Unterscheidungsmerkmale
- Pin-to-pin xE910 family migration path (vs. LE910C4-WWX)
- Lower system cost and simpler RF design than Cat.4 (vs. LE910C4-WWX)
- LTE-only platform with optional integrated GNSS (vs. ME910G1-EU)
Designhinweise
The LE910C1-EU is an LGA (land grid array) module: the castellated/LGA pads sit under the module body, so layout must follow the Telit LE910C1 Series Hardware User's Manual footprint exactly - including pad geometry, keep-out zones under the module, and via-in-pad or dog-bone fanout strategy. The antenna is not included, so route the RF feed with 50-ohm controlled impedance to the antenna connector or PCB antenna, and follow the manual's ground-plane and clearance recommendations. Validate the layout with Telit's design review checklist before tooling.
LTE Cat.1 transmitters draw significant burst current during RF transmissions - budget the 3.8V-class supply rail and its bulk capacitance for peak bursts, not average current, or the module will brown out during transmit slots. Place bulk capacitance close to the VBAT pins and use a supply capable of the peak current specified in the Telit hardware user's manual (consult the manual for the exact figure for your SKU). Verify voltage droop under worst-case transmit power at the antenna connector using the EVB 2.0 evaluation kit before finalizing the power tree.
Ordering codes matter: LE910C1-EU family variants (LE910C1EU13T131100 = code 25.21.223; LE910C1EU14T141100 = code 25.21.224) differ in hardware revision and feature configuration such as the GNSS option. Confirm the exact ordering code delivers quad-constellation GNSS if your application needs positioning. Also plan network sunset explicitly: this is an LTE-only Rel 10 platform, so it will not fall back to 2G/3G - if legacy fallback is required, evaluate the ME910G1-EU pin-compatible alternative instead.
Compliance-Informationen
Compliance declarations (RoHS/REACH/RED) were not present in the verified web data provided; obtain from Telit product compliance documentation for the specific ordering code.
