STMicroelectronics

LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics

Teilenummer: LM201ADT ✓ Aktiv
±5V to ±22V Vdss Low Id 8-pin SOIC, 3.5 mm nominal width Package
MOQ: 1 |

LM201ADT Übersicht

STMicroelectronics LM201ADT is a general-purpose precision operational amplifier in an 8-pin SOIC package. It operates from ±5V to ±22V, supports single or dual supplies, provides a 3.5 MHz gain-bandwidth product, and has a 0.5 V/µs slew rate. The LM201A series also includes input and output overload protection, low input offset current, and stable operation without oscillation when the common-mode input range is exceeded.

An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is determined primarily by external feedback components. The op amp category belongs to the broader amplifier-IC and signal-conditioning hierarchy, where precision amplifiers are used for current sensing, analog measurement, filtering, buffering, instrumentation, and closed-loop control. A precision operational amplifier is selected when low offset, controlled gain, and predictable operation are more important than very high bandwidth.

The LM201ADT combines a 22V maximum supply rating with moderate speed and precision-oriented behavior. Its 3.5 MHz gain-bandwidth product supports useful closed-loop bandwidth in amplifier networks of moderate gain, while its 0.5 V/µs slew rate limits large-signal response. Input and output overload protection improves robustness in applications where transient signals or output drive conditions may exceed normal operating limits.

The amplifier is not internally compensated, allowing engineers to select stability by adding an external compensation capacitor. The LM201A documentation describes compensation with a 30 pF capacitor. This flexibility supports unity-gain stability and higher closed-loop gains, but it also requires careful selection of compensation and feedback values to avoid ringing or oscillation.

Typical uses include instrumentation-amplifier front ends, precision current sensing, buffered sensor interfaces, active filters, analog measurement chains, and low-frequency control loops. The wide supply-voltage range is useful in industrial systems that use ±15V or ±22V rails, while its low-offset characteristics help preserve accuracy when the op amp operates near its input range.

Design with the LM201ADT by checking common-mode and output swing against the actual supply voltage. Keep feedback-loop routing short, place compensation and decoupling capacitors close to the device, and verify stability at the intended closed-loop gain. The STMicroelectronics LM201A datasheet is the controlling reference for pin functions, compensation, electrical limits, and test conditions.

This page combines the LM201ADT operating limits, package information, direct replacement considerations, comparison parameters, and practical design guidance to support faster component selection and PCB implementation.

Drop-in-Alternativen für LM201ADT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM201ADT (gleiche Bauform und Footprint) – abweichend in Slew Rate, Supply Voltage Range, Package, Gain-Bandwidth Product, Maximum Supply Voltage.

STMicroelectronics
Slew Rate: 0.5 V/us
Supply Voltage Range: +/-5 V to +/-22 V
Package: 8-SOIC
Vergleichen mit LM201ADT →
onsemi
Slew Rate: 10 V/us with proper compensation
Supply Voltage Range: 5 V to 20 V
Package: 8-SOIC
Vergleichen mit LM201ADT →

LM201AD

✅ Drop-In
STMicroelectronics
📦 SOIC-8
Single general-purpose operational amplifier · 1 circuit · 1 MHz (FindIC listing); 3.5 MHz (Mouser listing, condition not specified) · 0.5 V/us · +/-5 V to +/-22 V · 44 V · Push-Pull · Non-compensated

Preis auf Anfrage

Datenblatt ansehen →

LM201ADT Grenzwerte & elektrische Eigenschaften

Product Type General-purpose precision operational amplifier
Number of Amplifiers 1 amplifier
Supply Voltage Range ±5V to ±22V
Maximum Supply Voltage 22V
Gain-Bandwidth Product 3.5 MHz
Slew Rate 0.5 V/µs
Common-Mode Rejection Ratio 80 dB
Ausgangstyp Push-pull
Input Overload Protection Yes
Output Overload Protection Yes
Input Offset Current Low
Compensation Method External 30 pF capacitor
Gehäuse 8-pin SOIC, 3.5 mm nominal width
Montageart Surface mount
Dissipation 300 mW

LM201ADT 8-pin soic, 3.5 mm nominal width Pinbelegungsleitfaden

Pinbelegung für LM201ADT (8-pin soic, 3.5 mm nominal width-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für LM201ADT im 8-pin soic, 3.5 mm nominal width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LM201ADT.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LM201ADT ist geeignet für 6 Anwendungs: Precision Current Sensing, Instrumentation Signal Conditioning, Active Analog Filtering, Buffered Sensor Interface, Precision Control Loops, Analog Measurement Systems.

⚡

Precision Current Sensing

LM201ADT fits precision current-sensing front ends because its low input offset current and 80 dB common-mode rejection ratio help preserve measurement accuracy when the input signal sits on a substantial common-mode voltage. The single-amplifier configuration can amplify a small differential sensor output, while the 3.5 MHz gain-bandwidth product supports moderate-bandwidth control and measurement paths. Use an external 30 pF compensation capacitor where required, and verify that the input common-mode voltage, output swing, and 0.5 V/µs slew rate remain within the circuit’s worst-case limits.

🏭

Instrumentation Signal Conditioning

LM201ADT is suitable for instrumentation signal-conditioning stages that must amplify low-level differential sensor signals without excessive offset error. Its 80 dB common-mode rejection ratio reduces the effect of common-mode noise, while overload protection helps the amplifier tolerate transients around the measurement input. The device operates from ±5V to ±22V, allowing use in classic industrial analog systems. Choose the appropriate external compensation network, keep the feedback loop compact, and check input bias current against the source impedance for high-accuracy measurements.

📡

Active Analog Filtering

LM201ADT can implement active low-pass, high-pass, or band-pass filter sections where moderate bandwidth and precise gain are required. Its 3.5 MHz gain-bandwidth product gives useful bandwidth for many low-frequency industrial and control filters, while external compensation provides flexibility for unity-gain and higher-gain configurations. The ±5V to ±22V operating range supports laboratory and industrial rails. Select resistor and capacitor values against the required frequency response, include capacitor tolerances in the filter analysis, and verify phase margin with the final load and compensation arrangement.

🧩

Buffered Sensor Interface

LM201ADT provides input buffering for high-impedance sensors such as strain gauges, temperature sensors, and bridge outputs when the sensor requires a high input impedance and stable amplification. Low input offset current limits errors caused by sensor bias currents, and the 0.5 V/µs slew rate supports signals within the intended bandwidth. Because the LM201A architecture requires external compensation for the relevant stability configuration, add the manufacturer-recommended capacitor and confirm that the sensor’s common-mode voltage fits the device’s input range during startup, fault, and full-scale conditions.

🔧

Precision Control Loops

LM201ADT can serve as the error amplifier in low-frequency precision control systems where a 0.5 V/µs slew rate and 80 dB common-mode rejection ratio are sufficient. Its supply range supports ±5V through ±22V analog control rails, and the overload-protection features improve robustness during actuator transitions or unexpected feedback conditions. External compensation must be chosen for the intended loop gain and load. Analyze loop stability across temperature and supply tolerances, isolate high-current switching stages, and keep feedback routing away from noisy power-conversion nodes.

📺

Analog Measurement Systems

LM201ADT is appropriate for laboratory and industrial analog measurement systems that amplify bounded, low-frequency signals while preserving common-mode rejection. The 3.5 MHz gain-bandwidth product supports measurement bandwidth beyond basic DC operation, and the ±22V maximum supply rating provides compatibility with higher-voltage analog rails. For instrumentation use, account for input offset, bias current, slew-rate limits, and output swing in the uncertainty budget. Use the pin-description and compensation guidance in the manufacturer datasheet to avoid errors when adapting the circuit to a new board layout.

Where can I buy LM201ADT online?
Use the Request a Quote form on this page to request LM201ADT availability, current unit cost, and shipment options for your required quantity. The form provides a direct purchasing path without requiring engineers to compare unrelated package or grade variants. The LM201ADT ordering code identifies the 8-pin SOIC configuration, so include that complete MPN in the request and confirm the quantity and delivery requirements.
What is the price of LM201ADT?
The current LM201ADT unit price is not stated on this page; use the Request a Quote form to request pricing for the exact 8-pin SOIC ordering code and quantity. Pricing can vary with order volume and supply conditions, so a quotation for the required production quantity is more useful than a generic single-unit figure. No substitute package code or non-SOIC variant should be included in the request.
What is the lead time for LM201ADT?
The current lead time must be confirmed through the Request a Quote form on this page. It depends on the requested quantity, available inventory, and production scheduling at the time of quotation. Specify your required delivery date and target annual usage so the supplier can evaluate the appropriate supply plan. The request should identify LM201ADT exactly because other LM201A package codes are not interchangeable without board-level review.
Is LM201ADT in stock?
Current LM201ADT stock status should be confirmed through the Request a Quote form on this page. Enter the required quantity, assembly schedule, and delivery location when requesting availability. The product is offered for purchase by STMicroelectronics, but a quotation request is the appropriate method for obtaining a current, quantity-specific stock and shipment response rather than relying on an undated inventory indication.
LM201ADT vs onsemi LM201AD: which is better for instrumentation?
The STMicroelectronics LM201ADT and onsemi LM201AD are both single-amplifier, 8-pin SOIC devices from the LM201A family, so the primary selection criterion is verified electrical equivalence for the intended circuit. According to the LM201A documentation, the family supports ±5V to ±22V supplies, overload protection, and external compensation. Compare the complete datasheet values, especially offset, bias current, compensation requirements, and common-mode limits, before treating the onsemi device as interchangeable.
What is the difference between LM201ADT and LM201AD?
LM201ADT is the STMicroelectronics 8-pin SOIC ordering code, while LM201AD identifies the onsemi version listed as a single-circuit, push-pull, 8-SOIC amplifier. Both results identify the same amplifier family and package form, but the manufacturer and their individual datasheet limits remain part of the purchasing decision. For a direct substitution, compare offset voltage, input bias current, supply current, compensation, noise, output swing, and temperature ratings line by line.
When should I choose LM201ADT over onsemi LM201AD?
Choose the STMicroelectronics LM201ADT when its verified operating limits, qualification records, or supply arrangement are preferable for the design. Both candidates occupy the 8-pin SOIC footprint and belong to the LM201A family, so package migration alone does not decide the comparison. Use the device whose exact input, output, supply, temperature, and compensation specifications satisfy the worst-case circuit tolerances and production qualification requirements.
Is LM201ADT suitable for precision current sensing?
Yes, LM201ADT is suitable for precision current-sensing front ends when its low input offset current, 80 dB common-mode rejection ratio, and overload protection fit the measurement circuit. The part provides a 0.5 V/µs slew rate and 3.5 MHz gain-bandwidth product, which are suitable for many low-to-moderate-bandwidth sensing systems. The amplifier must remain inside its common-mode range, and input bias current and offset error should be included in the total measurement uncertainty.
What can replace LM201ADT?
The onsemi LM201AD is the clearest drop-in candidate identified for LM201ADT because it is also a single-circuit, push-pull amplifier in an 8-pin SOIC package from the LM201A family. Confirm the complete pinout, electrical limits, temperature grade, and compensation requirements against the STMicroelectronics datasheet before approving the substitution. Only the onsemi LM201AD has sufficient package and family support for the comparison presented here.
Is onsemi LM201AD the same as STMicroelectronics LM201ADT?
The onsemi LM201AD and STMicroelectronics LM201ADT share the LM201A family architecture, single-amplifier configuration, and 8-pin SOIC package format, but they are not automatically identical in every specification. A valid replacement requires matching supply range, input offset and bias current, common-mode range, output swing, slew rate, gain-bandwidth product, compensation method, temperature grade, and absolute maximum ratings. Treat it as a drop-in candidate until the manufacturer-specific datasheets have been compared.
Where do I download the LM201ADT datasheet PDF?
The manufacturer datasheet is available through the STMicroelectronics LM201A documentation linked from the product resources, while the LM201ADT PDF is also indexed by the STMicroelectronics datasheet result on AllDataSheet. Use the manufacturer PDF as the controlling document for design decisions. It identifies the LM201ADT ordering code, electrical characteristics, compensation guidance, package information, and operating limits used in this product summary.
Where can I find the LM201ADT pinout?
Use the pin configuration in the STMicroelectronics LM201A datasheet when assigning PCB tracks and checking the compensation connection. The LM201ADT uses an 8-pin SOIC package. Confirm pin numbers, supply locations, input polarity, output position, offset-null or no-connect status, and compensation requirements directly against the manufacturer drawing before releasing a PCB layout or changing an existing board.
What are the key specifications of LM201ADT that engineers should know?
The key LM201ADT specifications are a ±5V to ±22V supply range, 3.5 MHz gain-bandwidth product, 0.5 V/µs slew rate, 80 dB common-mode rejection ratio, and 8-pin SOIC packaging. According to the STMicroelectronics LM201A datasheet, the device also provides input and output overload protection, low input offset current, and external compensation using a 30 pF capacitor for appropriate stability configurations.
Does LM201ADT require an external compensation capacitor?
Yes, the LM201A family uses external compensation rather than being permanently internally compensated. The STMicroelectronics documentation identifies a 30 pF capacitor for the described compensation method. The correct capacitor value and stability depend on the selected closed-loop gain, noise-gain network, load, and board parasitics, so use the manufacturer compensation guidance and verify the final design with the intended gain and loading conditions.
Is LM201ADT RoHS compliant and AEC-Q100 qualified?
The RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status of LM201ADT are not established by the product information available for this page, so they remain unknown rather than assumed. Request the current compliance and qualification documents through the Request a Quote form when those declarations are mandatory. Automotive use also requires confirmation that the exact ordering code and manufacturer documentation satisfy the system’s qualification requirements.

Technische Referenzdaten für LM201ADT – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the STMicroelectronics LM201ADT when a general-purpose precision op amp is needed in an 8-pin SOIC design with ±5V to ±22V operation, a 3.5 MHz gain-bandwidth product, and external compensation. It is well suited to industrial instrumentation, current sensing, active filtering, buffered sensors, and low-frequency control loops. The onsemi LM201AD is the principal same-package replacement candidate identified, but approve it only after comparing input offset, bias current, common-mode range, output swing, compensation, temperature grade, and absolute maximum ratings. For new precision designs, both require stability verification at the intended gain and load. If the system can use a modern internally compensated amplifier, compare its offset, noise, bandwidth, supply voltage, and package separately because such devices may require a different footprint or stability strategy.

Vergleich mit Alternativen

Parameter Dieses Produkt LM201AD
Manufacturer STMicroelectronics onsemi
Package SOIC-8 SOIC-8
Amplifier Count 1 amplifier 1 amplifier
Output Type Push-pull Push-pull

Wichtigste Unterscheidungsmerkmale

  • Documented 3.5 MHz gain-bandwidth product (vs. LM201AD)
  • Wide high-voltage analog supply capability (vs. LM201AD)
  • Single-amplifier 8-pin SOIC compatibility (vs. LM201AD)

Designhinweise

Do not assume that all LM201A devices are interchangeable merely because they use the same 8-pin SOIC footprint. Confirm the complete pinout, compensation method, input offset, bias current, common-mode range, output swing, and temperature limits against the manufacturer datasheet. The external compensation requirement is particularly important because an incorrect capacitor value or feedback arrangement can make the amplifier unstable at the intended closed-loop gain.

Keep the op-amp feedback components and compensation capacitor close to their associated pins, and minimize the distance between the output and the inverting-input feedback path. Place input and supply bypass capacitors near the device, with short ground returns. Avoid routing high-current or switching-signal paths beneath the analog input and feedback nodes because the 80 dB common-mode rejection specification does not eliminate errors caused by coupled substrate or supply noise.

Check the output voltage and load current against both the supply rails and the 300 mW dissipation figure. Estimated: power dissipation equals the output-to-negative-supply voltage multiplied by load current, plus input-current contribution; for example, a 5 V output from a -15 V rail at 2 mA produces approximately 40 mW from the negative-supply path. Use this calculation only for preliminary thermal checks and retain the datasheet limits for final design approval.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance and qualification declarations are not stated in the available LM201ADT product information. Request current documentation through the Request a Quote form when formal compliance evidence is required.

Daten verifiziert am: 2026-11-10 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LM201ADT LM201ADT datasheet LM201ADT datasheet pdf LM201ADT pinout LM201ADT equivalent LM201ADT replacement LM201ADT vs LM201AD STMicroelectronics LM201ADT LM201ADT 22V op amp LM201ADT 3.5MHz SOIC-8 LM201ADT precision signal conditioning LM201ADT current sensing amplifier LM201ADT price LM201ADT stock LM201ADT application circuit

Verwandte Bauteile & Begriffe

STMicroelectronics LM201ADT LM201A LM201AD onsemi operational amplifier op amp precision amplifier single-amplifier IC signal conditioning current sensing instrumentation amplifier active filter sensor buffer analog measurement control loop common-mode rejection ratio CMRR slew rate gain-bandwidth product GBW external compensation 30 pF compensation capacitor SOIC-8 surface mount
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen