LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics
Артикул: LM201ADT ✓ АктивенLM201ADT Обзор
An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is determined primarily by external feedback components. The op amp category belongs to the broader amplifier-IC and signal-conditioning hierarchy, where precision amplifiers are used for current sensing, analog measurement, filtering, buffering, instrumentation, and closed-loop control. A precision operational amplifier is selected when low offset, controlled gain, and predictable operation are more important than very high bandwidth.
The LM201ADT combines a 22V maximum supply rating with moderate speed and precision-oriented behavior. Its 3.5 MHz gain-bandwidth product supports useful closed-loop bandwidth in amplifier networks of moderate gain, while its 0.5 V/µs slew rate limits large-signal response. Input and output overload protection improves robustness in applications where transient signals or output drive conditions may exceed normal operating limits.
The amplifier is not internally compensated, allowing engineers to select stability by adding an external compensation capacitor. The LM201A documentation describes compensation with a 30 pF capacitor. This flexibility supports unity-gain stability and higher closed-loop gains, but it also requires careful selection of compensation and feedback values to avoid ringing or oscillation.
Typical uses include instrumentation-amplifier front ends, precision current sensing, buffered sensor interfaces, active filters, analog measurement chains, and low-frequency control loops. The wide supply-voltage range is useful in industrial systems that use ±15V or ±22V rails, while its low-offset characteristics help preserve accuracy when the op amp operates near its input range.
Design with the LM201ADT by checking common-mode and output swing against the actual supply voltage. Keep feedback-loop routing short, place compensation and decoupling capacitors close to the device, and verify stability at the intended closed-loop gain. The STMicroelectronics LM201A datasheet is the controlling reference for pin functions, compensation, electrical limits, and test conditions.
This page combines the LM201ADT operating limits, package information, direct replacement considerations, comparison parameters, and practical design guidance to support faster component selection and PCB implementation.
Аналоги без доработки для LM201ADT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM201ADT (тот же форм-фактор и посадочное место) — отличается по Slew Rate, Supply Voltage Range, Package, Gain-Bandwidth Product, Maximum Supply Voltage.
LM201AD
✅ Прямая заменаУточнить цену
Открыть даташит →LM201ADT Максимальные параметры и электрические характеристики
| Product Type | General-purpose precision operational amplifier |
| Number of Amplifiers | 1 amplifier |
| Supply Voltage Range | ±5V to ±22V |
| Maximum Supply Voltage | 22V |
| Gain-Bandwidth Product | 3.5 MHz |
| Slew Rate | 0.5 V/µs |
| Common-Mode Rejection Ratio | 80 dB |
| Тип выхода | Push-pull |
| Input Overload Protection | Yes |
| Output Overload Protection | Yes |
| Input Offset Current | Low |
| Compensation Method | External 30 pF capacitor |
| Корпус | 8-pin SOIC, 3.5 mm nominal width |
| Тип монтажа | Surface mount |
| Dissipation | 300 mW |
Руководство по цоколевке LM201ADT в корпусе 8-pin soic, 3.5 mm nominal width
Цоколевка для LM201ADT (корпус 8-pin soic, 3.5 mm nominal width). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для LM201ADT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM201ADT подходит для 6 применениеs: Precision Current Sensing, Instrumentation Signal Conditioning, Active Analog Filtering, Buffered Sensor Interface, Precision Control Loops, Analog Measurement Systems.
Precision Current Sensing
LM201ADT fits precision current-sensing front ends because its low input offset current and 80 dB common-mode rejection ratio help preserve measurement accuracy when the input signal sits on a substantial common-mode voltage. The single-amplifier configuration can amplify a small differential sensor output, while the 3.5 MHz gain-bandwidth product supports moderate-bandwidth control and measurement paths. Use an external 30 pF compensation capacitor where required, and verify that the input common-mode voltage, output swing, and 0.5 V/µs slew rate remain within the circuit’s worst-case limits.
Рекомендуется
Instrumentation Signal Conditioning
LM201ADT is suitable for instrumentation signal-conditioning stages that must amplify low-level differential sensor signals without excessive offset error. Its 80 dB common-mode rejection ratio reduces the effect of common-mode noise, while overload protection helps the amplifier tolerate transients around the measurement input. The device operates from ±5V to ±22V, allowing use in classic industrial analog systems. Choose the appropriate external compensation network, keep the feedback loop compact, and check input bias current against the source impedance for high-accuracy measurements.
Рекомендуется
Active Analog Filtering
LM201ADT can implement active low-pass, high-pass, or band-pass filter sections where moderate bandwidth and precise gain are required. Its 3.5 MHz gain-bandwidth product gives useful bandwidth for many low-frequency industrial and control filters, while external compensation provides flexibility for unity-gain and higher-gain configurations. The ±5V to ±22V operating range supports laboratory and industrial rails. Select resistor and capacitor values against the required frequency response, include capacitor tolerances in the filter analysis, and verify phase margin with the final load and compensation arrangement.
Рекомендуется
Buffered Sensor Interface
LM201ADT provides input buffering for high-impedance sensors such as strain gauges, temperature sensors, and bridge outputs when the sensor requires a high input impedance and stable amplification. Low input offset current limits errors caused by sensor bias currents, and the 0.5 V/µs slew rate supports signals within the intended bandwidth. Because the LM201A architecture requires external compensation for the relevant stability configuration, add the manufacturer-recommended capacitor and confirm that the sensor’s common-mode voltage fits the device’s input range during startup, fault, and full-scale conditions.
Рекомендуется
Precision Control Loops
LM201ADT can serve as the error amplifier in low-frequency precision control systems where a 0.5 V/µs slew rate and 80 dB common-mode rejection ratio are sufficient. Its supply range supports ±5V through ±22V analog control rails, and the overload-protection features improve robustness during actuator transitions or unexpected feedback conditions. External compensation must be chosen for the intended loop gain and load. Analyze loop stability across temperature and supply tolerances, isolate high-current switching stages, and keep feedback routing away from noisy power-conversion nodes.
Рекомендуется
Analog Measurement Systems
LM201ADT is appropriate for laboratory and industrial analog measurement systems that amplify bounded, low-frequency signals while preserving common-mode rejection. The 3.5 MHz gain-bandwidth product supports measurement bandwidth beyond basic DC operation, and the ±22V maximum supply rating provides compatibility with higher-voltage analog rails. For instrumentation use, account for input offset, bias current, slew-rate limits, and output swing in the uncertainty budget. Use the pin-description and compensation guidance in the manufacturer datasheet to avoid errors when adapting the circuit to a new board layout.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM201ADT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM201AD |
|---|---|---|
| Manufacturer | STMicroelectronics | onsemi |
| Package | SOIC-8 | SOIC-8 |
| Amplifier Count | 1 amplifier | 1 amplifier |
| Output Type | Push-pull | Push-pull |
Ключевые отличия
- Documented 3.5 MHz gain-bandwidth product (против LM201AD)
- Wide high-voltage analog supply capability (против LM201AD)
- Single-amplifier 8-pin SOIC compatibility (против LM201AD)
Заметки по проектированию
Do not assume that all LM201A devices are interchangeable merely because they use the same 8-pin SOIC footprint. Confirm the complete pinout, compensation method, input offset, bias current, common-mode range, output swing, and temperature limits against the manufacturer datasheet. The external compensation requirement is particularly important because an incorrect capacitor value or feedback arrangement can make the amplifier unstable at the intended closed-loop gain.
Keep the op-amp feedback components and compensation capacitor close to their associated pins, and minimize the distance between the output and the inverting-input feedback path. Place input and supply bypass capacitors near the device, with short ground returns. Avoid routing high-current or switching-signal paths beneath the analog input and feedback nodes because the 80 dB common-mode rejection specification does not eliminate errors caused by coupled substrate or supply noise.
Check the output voltage and load current against both the supply rails and the 300 mW dissipation figure. Estimated: power dissipation equals the output-to-negative-supply voltage multiplied by load current, plus input-current contribution; for example, a 5 V output from a -15 V rail at 2 mA produces approximately 40 mW from the negative-supply path. Use this calculation only for preliminary thermal checks and retain the datasheet limits for final design approval.
Информация о соответствии
Compliance and qualification declarations are not stated in the available LM201ADT product information. Request current documentation through the Request a Quote form when formal compliance evidence is required.