LM201AVDR2 - 1MHz Non-Compensated Op Amp | onsemi
Teilenummer: LM201AVDR2 ✓ AktivLM201AVDR2 Übersicht
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable gain, filtering, buffering, or control functions. The LM201 belongs to the broader hierarchy of operational amplifiers, instrumentation amplifiers, analog amplifiers, and semiconductor signal-conditioning components. Unlike a unity-gain-stable device, the LM201 is non-compensated, allowing engineers to select external compensation values that optimize transient response or bandwidth for a particular circuit.
The primary device characteristics are its 1 MHz gain-bandwidth product, 0.5 V/us slew rate, single-amplifier configuration, and 8-SOIC package. Its non-compensated architecture is the key distinction from common unity-gain-stable precision amplifiers. That feature can support tailored loop behavior and gain-bandwidth relationships in instrumentation circuits, but it requires careful resistor and capacitor selection during design.
LM201AVDR2 is suited to applications where signal fidelity and controlled amplification matter more than wide-bandwidth performance. The 1 MHz bandwidth provides useful response for many low-frequency industrial and analog systems, while the 0.5 V/us slew rate favors measured or slow-moving waveforms rather than high-speed edges. Because the amplifier is non-compensated, the external compensation network strongly influences closed-loop bandwidth, stability, and usable slew rate.
Typical uses include low-level sensor amplification, process-control loops, data-acquisition channels, bridge-amplifier front ends, and analog instrumentation. It can also participate in filter and active-feedback designs where the designer intentionally selects compensation. In audio and communication equipment, it is best considered for slower analog paths rather than wideband signal chains.
The primary design consideration is stability. Configure external compensation according to the manufacturer’s recommended values for the intended closed-loop gain, and verify operation across the expected signal amplitude, frequency, load, and supply range. Decoupling capacitors should be placed close to the supply pins, and sensitive input routes should remain short and away from high-current output paths.
This product page combines the device identity, verified package and performance attributes, comparison information, and practical implementation guidance. It also identifies the limited availability of confirmed pin-to-pin alternatives so engineers can review fit, bandwidth, slew-rate, compensation, and supply requirements before making a replacement decision.
Drop-in-Alternativen für LM201AVDR2 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM201AVDR2 (gleiche Bauform und Footprint) – abweichend in Mounting Type, Package.
LM201AN
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM201AVDR2 Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Single, general-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Compensation | Non-compensated |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.5 V/us |
| Gehäuse | 8-SOIC |
| Montageart | Surface mount |
LM201AVDR2 8-soic Pinbelegungsleitfaden
Pinbelegung für LM201AVDR2 (8-soic-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM201AVDR2.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM201AVDR2 ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Process Control Loop Amplifier, Active Filter Signal Conditioning, Audio and Communication Analog Path, Data Acquisition Front End, Precision Instrumentation Amplifier Stage.
Industrial Sensor Signal Conditioning
The LM201AVDR2 fits low-level industrial sensor front ends where amplification must be tailored to the transducer and measurement bandwidth. Its 1 MHz gain-bandwidth product is appropriate for many temperature, pressure, and position signals, while external compensation gives the designer control over closed-loop behavior at the required gain. The device is used between the sensor and an ADC or controller, where offset, bias current, noise, and common-mode limits determine measurement accuracy. Because the 8-SOIC amplifier is non-compensated, select the feedback and compensation network from the manufacturer’s gain-specific guidance rather than assuming unity-gain stability.
Empfohlen
Process Control Loop Amplifier
LM201AVDR2 can serve as the error amplifier in a process-control loop when the designer intentionally sets the compensation characteristics. Its 0.5 V/us slew rate supports many slow actuator commands, and the 1 MHz gain-bandwidth product is generally sufficient for loops operating well below that level. The non-compensated architecture allows the feedback and frequency-shaping components to be optimized for a particular plant, sensor, and actuator. Validate loop stability over the full command range because large-signal behavior and compensation determine whether the loop remains stable and responsive.
Empfohlen
Active Filter Signal Conditioning
The LM201AVDR2 is well suited to active filtering when each amplifier stage has a known gain and the compensation network can be selected deliberately. Its 1 MHz gain-bandwidth product provides useful bandwidth for many low-frequency measurement chains, and the 0.5 V/us slew rate limits large-signal performance in demanding waveforms. In a filter application, the amplifier is connected with feedback and compensation elements that establish the transfer function. Check component tolerances, phase margin, and output swing because changing filter resistance or capacitance can alter both signal amplitude and stability.
Empfohlen
Audio and Communication Analog Path
LM201AVDR2 can support slow analog paths in audio and communication equipment, provided the external compensation is matched to the closed-loop gain. Its 1 MHz bandwidth and 0.5 V/us slew rate are more appropriate for control, monitoring, or baseband functions than for wideband audio reproduction. The amplifier may be used for impedance buffering, gain shaping, or active filtering around an audio or communications channel. Designers should evaluate noise, slew-rate-induced distortion, output loading, and supply headroom against the waveform rather than using bandwidth alone as the acceptance criterion.
Empfohlen
Data Acquisition Front End
The LM201AVDR2 can condition analog inputs before conversion in a data-acquisition system, especially when the source is low speed and the required gain is known. A 1 MHz gain-bandwidth product supports many multiplexed measurement channels, while the 0.5 V/us slew rate is suitable for slowly changing sensor outputs. The non-compensated device requires an explicit external network, so the amplifier’s feedback topology must be evaluated at the actual closed-loop gain and source impedance. Pay particular attention to offset, bias current, common-mode range, and conversion accuracy rather than treating the amplifier as an ideal buffer.
Empfohlen
Precision Instrumentation Amplifier Stage
LM201AVDR2 is appropriate as a gain stage in precision instrumentation when the circuit requires a non-compensated amplifier and the designer can establish an exact operating gain. Its single-amplifier 8-SOIC implementation allows each channel to be tailored for the sensor impedance, bandwidth, and dynamic range. The 1 MHz gain-bandwidth product and 0.5 V/us slew rate support many precision but slow measurement paths. For highest accuracy, combine the datasheet’s offset, bias-current, noise, and common-mode limits with the complete error budget, and confirm that external compensation remains stable across the expected signal and load conditions.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM201AVDR2 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM201 |
|---|---|---|
| Brand | onsemi | Analog Devices |
| Package | 8-SOIC | 8-SOIC |
| Amplifier Type | Non-compensated general-purpose amplifier | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz | 1 MHz |
| Compensation | External compensation required | External compensation required |
Wichtigste Unterscheidungsmerkmale
- Externally adjustable compensation supports purpose-designed closed-loop behavior (vs. LM201)
- Single-amplifier 8-SOIC implementation simplifies one-channel analog boards (vs. LM201)
- Established low-frequency performance for instrumentation-class signal paths (vs. LM201)
Designhinweise
Do not treat LM201AVDR2 as unity-gain stable. Its 1 MHz gain-bandwidth product is a small-signal parameter, and the usable response depends on the selected closed-loop gain and external compensation network. Start with the manufacturer’s compensation examples for the intended gain, then verify phase margin and output behavior with the actual source impedance and load. A circuit that is stable at one gain can require different compensation values at another.
Place the input, output, feedback, and compensation paths for short and compact routing. Connect the supply-bypass capacitor directly between the supply and ground pins, and keep sensitive input nodes away from the output and other high-current paths. The 0.5 V/us slew rate of LM201AVDR2 means that fast edges can excite capacitive feedback through board and package parasitics. Grounding the compensation capacitors directly at the relevant device ground reference reduces additional feedback paths.
Verify large-signal behavior rather than relying only on the 1 MHz gain-bandwidth figure. The 0.5 V/us slew rate establishes how quickly the output can move, so the highest undistorted output frequency depends on amplitude and the gain configuration. Use the manufacturer’s recommended compensation, check output swing on the selected supply, and evaluate capacitive loading. This is especially important when driving an ADC input, cable, or downstream stage with substantial capacitance.
Compliance-Informationen
Compliance declarations were not identified for the exact LM201AVDR2 ordering code. Confirm the current onsemi product documentation and lot-specific material declaration before release.