onsemi

LM201AVDR2 - 1MHz Non-Compensated Op Amp | onsemi

MPN: LM201AVDR2 ✓ Aktif
8-SOIC Package
MOQ: 1 |

LM201AVDR2 Ringkasan

onsemi LM201AVDR2 is a single, non-compensated, general-purpose operational amplifier designed for instrumentation and low-frequency signal-processing applications. It provides one amplifier circuit in an 8-pin SOIC package, with a gain-bandwidth product of 1 MHz and a slew rate of 0.5 V/us. These figures position the device as a stable choice for slow sensor signals, analog control loops, and applications requiring external frequency compensation.

An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable gain, filtering, buffering, or control functions. The LM201 belongs to the broader hierarchy of operational amplifiers, instrumentation amplifiers, analog amplifiers, and semiconductor signal-conditioning components. Unlike a unity-gain-stable device, the LM201 is non-compensated, allowing engineers to select external compensation values that optimize transient response or bandwidth for a particular circuit.

The primary device characteristics are its 1 MHz gain-bandwidth product, 0.5 V/us slew rate, single-amplifier configuration, and 8-SOIC package. Its non-compensated architecture is the key distinction from common unity-gain-stable precision amplifiers. That feature can support tailored loop behavior and gain-bandwidth relationships in instrumentation circuits, but it requires careful resistor and capacitor selection during design.

LM201AVDR2 is suited to applications where signal fidelity and controlled amplification matter more than wide-bandwidth performance. The 1 MHz bandwidth provides useful response for many low-frequency industrial and analog systems, while the 0.5 V/us slew rate favors measured or slow-moving waveforms rather than high-speed edges. Because the amplifier is non-compensated, the external compensation network strongly influences closed-loop bandwidth, stability, and usable slew rate.

Typical uses include low-level sensor amplification, process-control loops, data-acquisition channels, bridge-amplifier front ends, and analog instrumentation. It can also participate in filter and active-feedback designs where the designer intentionally selects compensation. In audio and communication equipment, it is best considered for slower analog paths rather than wideband signal chains.

The primary design consideration is stability. Configure external compensation according to the manufacturer’s recommended values for the intended closed-loop gain, and verify operation across the expected signal amplitude, frequency, load, and supply range. Decoupling capacitors should be placed close to the supply pins, and sensitive input routes should remain short and away from high-current output paths.

This product page combines the device identity, verified package and performance attributes, comparison information, and practical implementation guidance. It also identifies the limited availability of confirmed pin-to-pin alternatives so engineers can review fit, bandwidth, slew-rate, compensation, and supply requirements before making a replacement decision.

Pilihan pengganti yang segera untuk LM201AVDR2 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera LM201AVDR2 (sama faktor bentuk dan kaki) — berbeza dalam Mounting Type, Package.

STMicroelectronics
Mounting Type: Through-hole
Package: 8-pin PDIP
Bandingkan Dengan LM201AVDR2 →

LM201AN

✅ Masuk Drop-In
STMicroelectronics
📦 8-SOIC
General-purpose operational amplifier · 1 circuit · Non-compensated; external compensation capacitor · 20 nA · 10 V/µs

Hubungi untuk harga

Lihat Datasheet →

LM201AVDR2 Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Single, general-purpose operational amplifier
Number of Circuits 1 circuit
Compensation Non-compensated
Gain-Bandwidth Product 1 MHz
Slew Rate 0.5 V/us
Kemasan 8-SOIC
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin LM201AVDR2 8-soic

Konfigurasi pin untuk LM201AVDR2 (8-soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-soic untuk LM201AVDR2

Tiada data garisan pin yang diperoleh untuk LM201AVDR2.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LM201AVDR2 patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Process Control Loop Amplifier, Active Filter Signal Conditioning, Audio and Communication Analog Path, Data Acquisition Front End, Precision Instrumentation Amplifier Stage.

🏭

Industrial Sensor Signal Conditioning

The LM201AVDR2 fits low-level industrial sensor front ends where amplification must be tailored to the transducer and measurement bandwidth. Its 1 MHz gain-bandwidth product is appropriate for many temperature, pressure, and position signals, while external compensation gives the designer control over closed-loop behavior at the required gain. The device is used between the sensor and an ADC or controller, where offset, bias current, noise, and common-mode limits determine measurement accuracy. Because the 8-SOIC amplifier is non-compensated, select the feedback and compensation network from the manufacturer’s gain-specific guidance rather than assuming unity-gain stability.

⚙️

Process Control Loop Amplifier

LM201AVDR2 can serve as the error amplifier in a process-control loop when the designer intentionally sets the compensation characteristics. Its 0.5 V/us slew rate supports many slow actuator commands, and the 1 MHz gain-bandwidth product is generally sufficient for loops operating well below that level. The non-compensated architecture allows the feedback and frequency-shaping components to be optimized for a particular plant, sensor, and actuator. Validate loop stability over the full command range because large-signal behavior and compensation determine whether the loop remains stable and responsive.

🎛️

Active Filter Signal Conditioning

The LM201AVDR2 is well suited to active filtering when each amplifier stage has a known gain and the compensation network can be selected deliberately. Its 1 MHz gain-bandwidth product provides useful bandwidth for many low-frequency measurement chains, and the 0.5 V/us slew rate limits large-signal performance in demanding waveforms. In a filter application, the amplifier is connected with feedback and compensation elements that establish the transfer function. Check component tolerances, phase margin, and output swing because changing filter resistance or capacitance can alter both signal amplitude and stability.

🌐

Audio and Communication Analog Path

LM201AVDR2 can support slow analog paths in audio and communication equipment, provided the external compensation is matched to the closed-loop gain. Its 1 MHz bandwidth and 0.5 V/us slew rate are more appropriate for control, monitoring, or baseband functions than for wideband audio reproduction. The amplifier may be used for impedance buffering, gain shaping, or active filtering around an audio or communications channel. Designers should evaluate noise, slew-rate-induced distortion, output loading, and supply headroom against the waveform rather than using bandwidth alone as the acceptance criterion.

🖥️

Data Acquisition Front End

The LM201AVDR2 can condition analog inputs before conversion in a data-acquisition system, especially when the source is low speed and the required gain is known. A 1 MHz gain-bandwidth product supports many multiplexed measurement channels, while the 0.5 V/us slew rate is suitable for slowly changing sensor outputs. The non-compensated device requires an explicit external network, so the amplifier’s feedback topology must be evaluated at the actual closed-loop gain and source impedance. Pay particular attention to offset, bias current, common-mode range, and conversion accuracy rather than treating the amplifier as an ideal buffer.

🔬

Precision Instrumentation Amplifier Stage

LM201AVDR2 is appropriate as a gain stage in precision instrumentation when the circuit requires a non-compensated amplifier and the designer can establish an exact operating gain. Its single-amplifier 8-SOIC implementation allows each channel to be tailored for the sensor impedance, bandwidth, and dynamic range. The 1 MHz gain-bandwidth product and 0.5 V/us slew rate support many precision but slow measurement paths. For highest accuracy, combine the datasheet’s offset, bias-current, noise, and common-mode limits with the complete error budget, and confirm that external compensation remains stable across the expected signal and load conditions.

What is the onsemi LM201AVDR2?
The onsemi LM201AVDR2 is a single, non-compensated, general-purpose operational amplifier packaged in an 8-pin SOIC. According to onsemi’s manufacturer datasheet, the device has a gain-bandwidth product of 1 MHz and a slew rate of 0.5 V/us. Its non-compensated architecture makes it useful when the external compensation network must be selected for a particular closed-loop gain, feedback topology, or signal bandwidth. It is intended for instrumentation and general-purpose low-frequency analog applications rather than unity-gain-stable operation without compensation.
What are the key specifications of LM201AVDR2 that engineers should know?
The LM201AVDR2 is a one-circuit, non-compensated operational amplifier with a 1 MHz gain-bandwidth product and 0.5 V/us slew rate in an 8-SOIC package. According to onsemi’s manufacturer datasheet, its defining electrical characteristic is the external-compensation requirement. Designers should treat the compensation network, gain setting, load, and supply voltage as a coordinated design rather than selecting the amplifier independently. Use the datasheet pin-description table and recommended compensation examples to establish the complete implementation.
Where can I download the LM201AVDR2 datasheet PDF?
The official onsemi LM201AVDR2 datasheet PDF is available through the onsemi documentation link listed on this page. According to onsemi’s manufacturer datasheet, LM201AVDR2 contains one non-compensated amplifier circuit in an 8-SOIC package. The document is the primary reference for supply limits, electrical characteristics, pin assignments, compensation guidance, and recommended application circuits. Before layout or replacement work, verify the complete pin-description table against the selected package and operating conditions.
Where can I find the LM201AVDR2 pinout?
The LM201AVDR2 pinout is documented in onsemi’s manufacturer datasheet under the package and pin-description information for the 8-SOIC package. Use that table when assigning the amplifier inputs, output, supply terminals, and compensation-network connections. The 8-SOIC footprint is represented by the package diagram associated with this page, but functional pin names should always be taken from the manufacturer pin table. Do not infer compensation or offset-null connections from a generic SOIC drawing.
Is LM201AVDR2 suitable for sensor signal conditioning?
Yes, LM201AVDR2 is suitable for many low-level sensor signal-conditioning applications when the external compensation is designed for the required closed-loop gain. Its 1 MHz gain-bandwidth product and 0.5 V/us slew rate are appropriate for many industrial, process-control, and instrumentation signals rather than high-speed waveforms. According to onsemi’s manufacturer datasheet, the non-compensated topology requires deliberate network selection. A practical design should also verify input common-mode range, output swing, offset, noise, and supply limits for the specific sensor.
Can LM201AVDR2 be used for active filters?
The LM201AVDR2 can be used in active-filter designs because its non-compensated architecture permits the external compensation network to be tailored to the filter topology and target response. Its 1 MHz gain-bandwidth product and 0.5 V/us slew rate are suitable for many low-frequency active filters. According to onsemi’s manufacturer datasheet, however, stable operation depends on the selected feedback and compensation values. Simulate gain, phase margin, component tolerance, and expected signal amplitude rather than treating the amplifier as a fixed unity-gain-stable building block.
What can replace LM201AVDR2?
The closest confirmed cross-family replacement is the Analog Devices LM201, identified as a pin-to-pin replacement for the LM201 family in the available cross-reference information. A valid replacement must also satisfy the application’s supply voltage, compensation approach, gain-bandwidth product, slew-rate, offset, noise, and package requirements. The LM201AVDR2 offers 1 MHz bandwidth and 0.5 V/us slew rate, so a nominal pin match alone does not guarantee identical transient performance. Review the complete electrical tables before approving a substitution.
Is LM201AVDR2 the same as LM201AV?
The LM201AVDR2 is the onsemi ordering designation for the 8-SOIC LM201A device, including its exact suffix and shipment format. The base LM201AV designation identifies the same underlying device family before the full ordering code is applied, but procurement engineers should use the complete manufacturer MPN when checking package, reel format, and stock. Both references should point to the same 1 MHz, 0.5 V/us, single-amplifier electrical identity in the onsemi ordering information.
LM201AVDR2 vs LM201 from Analog Devices — which is better for precision instrumentation?
Choose LM201AVDR2 when the design is specifically qualified around onsemi’s documented LM201A characteristics, while the Analog Devices LM201 is the confirmed pin-compatible cross-family option. The LM201AVDR2 is specified at 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and one non-compensated amplifier in 8-SOIC. For precision instrumentation, compare input offset voltage, bias current, noise, common-mode range, supply range, and recommended compensation. The correct choice is the part whose full electrical envelope satisfies the measured signal and error budget.
When should I choose LM201AVDR2 over a unity-gain-stable op amp?
Choose LM201AVDR2 when the circuit benefits from selectable external compensation, particularly in a non-inverting, inverting, or active-feedback topology whose stability and bandwidth can be designed explicitly. Its 1 MHz gain-bandwidth product and 0.5 V/us slew rate make it relevant to instrumentation and low-frequency analog control. A unity-gain-stable amplifier is generally simpler when minimum closed-loop gain, large capacitive loading, or a broad range of operating gains must be handled without redesigning the compensation network.
What design constraints matter most for LM201AVDR2?
The most important design constraint is stable operation with the selected external compensation values. According to onsemi’s manufacturer datasheet, LM201AVDR2 is a non-compensated 1 MHz, 0.5 V/us operational amplifier, so gain, feedback impedance, compensation capacitance, load, and output amplitude interact closely. Check the recommended compensation examples for the intended closed-loop gain, place supply decoupling close to the device, and verify that the source impedance does not worsen noise or bias-current effects. Stability and usable bandwidth must be evaluated together.
How should LM201AVDR2 be decoupled on a PCB?
Place the supply-bypass capacitors directly between the supply pin and ground pin, with the shortest and lowest-inductance routing practical. Keep the amplifier’s sensitive input traces short, avoid routing them beside high-current outputs, and return compensation-component grounds cleanly to the device ground reference. Although the LM201AVDR2 operates in the 8-SOIC package and has a 1 MHz gain-bandwidth product, bypassing and layout still determine whether the circuit achieves its intended noise and transient behavior. Confirm capacitor type, voltage rating, and placement against the manufacturer’s application guidance.
Is LM201AVDR2 in stock and what is the lead time?
Current stock and lead time for LM201AVDR2 should be confirmed through the Request a Quote form on this page. The part is a catalogued onsemi 8-SOIC operational amplifier with a 1 MHz gain-bandwidth product and 0.5 V/us slew rate, but availability can vary by lot, region, and shipment format. Submit the exact MPN, required quantity, and target delivery location with the quotation request so the current manufacturing and logistics position can be confirmed without relying on outdated listing information.
Where can I buy LM201AVDR2 and what is the price?
Use the Request a Quote form on this page to obtain current LM201AVDR2 availability, lead time, and commercial terms. The exact onsemi MPN identifies a single non-compensated amplifier in an 8-SOIC package with a 1 MHz gain-bandwidth product and 0.5 V/us slew rate. For a production BOM, request the required quantity, reel or other shipment format, traceability requirements, and delivery location. The quotation process prevents an archived unit price from being mistaken for current inventory or a guaranteed procurement commitment.
Is LM201AVDR2 compliant with RoHS and REACH?
The LM201AVDR2’s RoHS and REACH status must be confirmed from the current onsemi product documentation or the material declaration associated with the ordered lot. onsemi’s manufacturer datasheet establishes the electrical identity, including the 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and 8-SOIC package, but the environmental declarations should be checked for the exact ordering code. Procurement and compliance teams should retain the declaration applicable to the production lot and shipment configuration.

Data referensi kejuruteraan untuk LM201AVDR2 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose LM201AVDR2 when the design uses onsemi’s LM201A implementation, needs a single non-compensated amplifier in an 8-SOIC package, and can select external compensation for the intended gain. Its 1 MHz gain-bandwidth product and 0.5 V/us slew rate are well suited to industrial sensors, process-control error amplifiers, active filters, and slow data-acquisition channels. Select the Analog Devices LM201 when its exact electrical table offers a better match for the required supply range, offset, bias current, noise, or compensation recommendations. Do not choose either part solely from package appearance: the device is non-compensated, so verify stability at every intended closed-loop gain. A unity-gain-stable amplifier is preferable when the minimum operating gain is unrestricted, capacitive loads are uncertain, or the circuit must tolerate broad gain changes without a separate compensation redesign.

Perbandingan dengan Gantian

Parametr Produk Ini LM201
Brand onsemi Analog Devices
Package 8-SOIC 8-SOIC
Amplifier Type Non-compensated general-purpose amplifier General-purpose operational amplifier
Gain-Bandwidth Product 1 MHz 1 MHz
Compensation External compensation required External compensation required

Penyeberangsung Jelas

  • Externally adjustable compensation supports purpose-designed closed-loop behavior (vsLM201)
  • Single-amplifier 8-SOIC implementation simplifies one-channel analog boards (vsLM201)
  • Established low-frequency performance for instrumentation-class signal paths (vsLM201)

Catatan Desain

Do not treat LM201AVDR2 as unity-gain stable. Its 1 MHz gain-bandwidth product is a small-signal parameter, and the usable response depends on the selected closed-loop gain and external compensation network. Start with the manufacturer’s compensation examples for the intended gain, then verify phase margin and output behavior with the actual source impedance and load. A circuit that is stable at one gain can require different compensation values at another.

Place the input, output, feedback, and compensation paths for short and compact routing. Connect the supply-bypass capacitor directly between the supply and ground pins, and keep sensitive input nodes away from the output and other high-current paths. The 0.5 V/us slew rate of LM201AVDR2 means that fast edges can excite capacitive feedback through board and package parasitics. Grounding the compensation capacitors directly at the relevant device ground reference reduces additional feedback paths.

Verify large-signal behavior rather than relying only on the 1 MHz gain-bandwidth figure. The 0.5 V/us slew rate establishes how quickly the output can move, so the highest undistorted output frequency depends on amplitude and the gain configuration. Use the manufacturer’s recommended compensation, check output swing on the selected supply, and evaluate capacitive loading. This is especially important when driving an ADC input, cable, or downstream stage with substantial capacitance.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance declarations were not identified for the exact LM201AVDR2 ordering code. Confirm the current onsemi product documentation and lot-specific material declaration before release.

Pencarian Berhubungan

LM201AVDR2 datasheet LM201AVDR2 specifications LM201AVDR2 pinout LM201AVDR2 datasheet pdf onsemi LM201AVDR2 LM201AVDR2 1MHz amplifier LM201AVDR2 0.5 V/us LM201AVDR2 8-SOIC pinout LM201AVDR2 equivalent LM201AVDR2 replacement LM201AVDR2 vs LM201 LM201AVDR2 application circuit LM201AVDR2 price LM201AVDR2 stock

Komponen dan Tanda berkaitan

onsemi LM201AVDR2 LM201AV LM201 Analog Devices operational amplifier single operational amplifier non-compensated amplifier general-purpose amplifier instrumentation amplifier analog signal conditioning active filter process control data acquisition gain-bandwidth product 1 MHz gain-bandwidth product 0.5 V/us slew rate 8-SOIC package SOIC family surface-mount package external compensation negative feedback RoHS REACH AEC-Q100
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ