LM258AWYPT - Dual 30V Low-Power Op Amp | STMicroelectronics
Teilenummer: LM258AWYPT ✓ AktivLM258AWYPT Übersicht
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. When negative feedback is applied, the device creates a closed-loop gain determined mainly by external resistors. The operational-amplifier category belongs to the amplifier IC hierarchy, which includes instrumentation, precision, and general-purpose amplifiers used for signal conditioning, control, and system-level analog processing.
The LM258AWYPT provides two amplifiers in one compact package. Key electrical characteristics include a 1.1 MHz gain-bandwidth product, 600 V/ms slew rate, 55 nV/√Hz noise density at 1 kHz, 85 dB common-mode rejection, and a 700 µA quiescent-current figure. Its operating temperature range of -40°C to +105°C supports industrial environments where consumer-grade amplifiers may be unsuitable.
Each amplifier is internally frequency compensated, allowing stable operation without an external compensation capacitor in the standard closed-loop configurations. The device supports single-supply operation from 3 V to 30 V and dual-supply operation when the mid-supply reference is established appropriately. Its low quiescent current helps limit power consumption in battery-powered and distributed sensing systems.
Typical applications include low-side current measurement, transducer conditioning, industrial sensor interfaces, feedback networks in power-control circuits, audio preamplification, and general buffered analog stages. Two independent amplifiers in one package can also implement a differential amplifier or instrumentation-style front end when suitable resistor networks and component tolerances are used.
For PCB design, keep feedback resistors close to the associated input pins and maintain a low-impedance return path for each amplifier. Avoid long traces between the two amplifier channels when they carry different signals. Confirm output swing, common-mode range, stability, and input protection under the worst-case supply and load conditions before production release.
This product page consolidates the LM258AWYPT electrical characteristics, verified package information, sourcing options, pin mapping, and practical guidance for engineers evaluating this low-power dual operational amplifier.
Drop-in-Alternativen für LM258AWYPT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM258AWYPT (gleiche Bauform und Footprint) – abweichend in Amplifier Type, Input Bias Current, Package, Slew Rate, Input Offset Current.
LM358AWYPT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM258AWYPT Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Supply Voltage Range | 3 V to 30 V |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 600 V/ms |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 2 nA |
| Input Offset Current | 20 nA |
| Voltage Noise Density | 55 nV/√Hz at 1 kHz |
| Output Current | 40 mA |
| Ruhestrom | 700 µA |
| Common-Mode Rejection Ratio | 85 dB |
| Input Offset Voltage Temperature Drift | 7 µV/°C |
| Input Bias Current Temperature Drift | 10 pA/°C |
| Betriebstemperaturbereich | -40°C to +105°C |
| Gehäuse | TSSOP-8 |
| Montageart | Surface mount |
| RoHS-Status | Compliant |
LM258AWYPT Pin-Konfiguration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | IN2+ — Amplifier 2 non-inverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | V+ — Positive supply connection |
Typische Anwendungen
LM258AWYPT ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Battery-Powered Remote Sensing, Audio Preamplification, Power-Control Feedback Networks, Data Acquisition and Instrumentation.
Industrial Sensor Signal Conditioning
The LM258AWYPT is suitable for conditioning resistive, voltage-based, and low-current sensors in industrial equipment. Each internally compensated amplifier can provide non-inverting gain, buffering, or active filtering within its 1.1 MHz gain-bandwidth product. The 85 dB common-mode rejection specification helps reduce corruption when the sensor signal is small relative to the common-mode voltage. With two independent amplifiers in one TSSOP-8 package, designers can pair the sensor amplifier with a filter or output driver. The -40°C to +105°C rating supports industrial environments, although the input common-mode range and output swing must be checked at the minimum 3 V supply.
Empfohlen
Low-Side Current Measurement
The LM258AWYPT can amplify the voltage generated by a low-side current-sense shunt in motor, power-supply, and battery-monitoring systems. The 600 V/ms slew rate allows the amplifier to respond quickly to current transients, while the 55 nV/√Hz noise density at 1 kHz helps preserve small shunt-voltage signals. A differential arrangement can use both amplifiers, although resistor matching determines common-mode rejection in practice. Because the listed common-mode rejection is 85 dB, layout symmetry and precision resistors remain important. The 700 µA quiescent current contributes little overhead in systems where the shunt current is substantially higher.
Empfohlen
Battery-Powered Remote Sensing
The LM258AWYPT is appropriate for low-voltage remote sensor nodes because it operates from a 3 V supply and has a listed 700 µA quiescent current. Two amplifiers can form a non-inverting front end and an active low-pass or level-shifting stage, reducing the component count compared with separate single amplifiers. The -40°C to +105°C range also permits operation in outdoor industrial enclosures where temperature varies substantially. Designers should calculate the complete sleep and active energy budget, including divider current and sensor load, and should disable unused channels or the entire device during long storage periods to reduce leakage losses.
Empfohlen
Audio Preamplification
The LM258AWYPT can provide moderate-gain audio preamplification in small microphone, line-level, and mixer circuits. Its 55 nV/√Hz voltage-noise density at 1 kHz and 1.1 MHz gain-bandwidth product support low-frequency audio stages, while the 600 V/ms slew rate helps avoid excessive distortion on larger transients. The dual configuration can provide two independent mono channels when the circuit layout keeps the channels electrically and physically separate. For microphones requiring substantial gain, input bias current of 2 nA helps preserve source loading behavior. Feedback resistor values should keep closed-loop bandwidth below the amplifier's gain-bandwidth limit and avoid driving capacitive microphone cables directly.
Empfohlen
Power-Control Feedback Networks
The LM258AWYPT can amplify error signals and drive feedback paths in linear power-control systems, including regulated supplies and actuator controllers. Its 30 V maximum supply and 1.1 MHz gain-bandwidth product are useful for systems that require wider loop bandwidth than a very slow precision amplifier provides. The internal frequency compensation simplifies the implementation of conventional voltage-feedback configurations. However, the 40 mA output-current rating must be checked against transient load requirements, and output saturation should be evaluated at the actual load because the usable swing is narrower than the supply rails.
Empfohlen
Data Acquisition and Instrumentation
The LM258AWYPT is useful in entry-level data-acquisition modules that buffer sensor outputs and interface signals to an ADC. One channel can amplify the selected measurement while the other provides a complementary reference, filter, or output driver. Its 85 dB common-mode rejection and 700 µA quiescent current provide a practical balance for general-purpose instrumentation, while the TSSOP-8 package simplifies compact analog boards. Designers should maintain matched resistor networks for differential measurements, verify the ADC input range, and place the amplifier close to the source to minimize noise pickup before long PCB traces reach the converter.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM258AWYPT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM358AWYPT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | TSSOP-8 | TSSOP-8 |
| Amplifier Configuration | Dual | Dual |
| Product Class | Low-power general-purpose operational amplifier | Low-power general-purpose operational amplifier |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz |
Wichtigste Unterscheidungsmerkmale
- Specified for extended industrial temperature operation (vs. LM358AWYPT)
- Wide single-supply operating range (vs. LM358AWYPT)
- Two amplifiers in a compact TSSOP-8 package (vs. LM358AWYPT)
Designhinweise
Place the feedback resistors directly beside the relevant LM258AWYPT input and output pins. For high-impedance sources, keep input traces short, avoid routing them parallel to switching-node copper, and provide a quiet ground return. If both channels process independent signals, maintain physical separation to reduce capacitive coupling. Pin 8 should have a short, low-impedance supply path, while pin 4 should connect to the system ground plane or the negative supply in a dual-supply arrangement.
Use resistor ratios that keep the closed-loop bandwidth safely below the 1.1 MHz gain-bandwidth product. A practical rule is to compare the selected closed-loop gain with the amplifier's gain-bandwidth product and verify phase margin using the manufacturer's stability guidance. Account for parasitic capacitance when driving long cables or ADC sample-and-hold inputs. The 55 nV/√Hz noise density is useful for signal-chain planning, but resistor thermal noise and layout leakage can become important when working with high source impedances.
Do not assume that the full 3 V to 30 V supply range permits equal input and output swings. Check the input common-mode range and output swing at the lowest supply voltage, particularly when using the device at 3 V or with loads near the listed 40 mA rating. Also verify that dual-supply operation uses pin 4 as the negative supply rather than grounding it, and that input voltages remain within the absolute maximum ratings during power-down. Add input protection when transients can exceed the operating range.
Compliance-Informationen
The component listing identifies LM258AWYPT as RoHS compliant. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was provided for this orderable code.