STMicroelectronics

LM258AWYPT - Dual 30V Low-Power Op Amp | STMicroelectronics

Référence : LM258AWYPT ✓ Actif
3 V to 30 V Vdss 2 nA Id TSSOP-8 Package
MOQ : 1 |

LM258AWYPT Présentation

The STMicroelectronics LM258AWYPT is a dual, general-purpose operational amplifier with two independent amplifiers, a 1.1 MHz gain-bandwidth product, and a 3 V to 30 V supply-voltage range in an 8-pin TSSOP package. Its low-power design is intended for industrial control, sensor conditioning, and general analog signal-chain applications.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. When negative feedback is applied, the device creates a closed-loop gain determined mainly by external resistors. The operational-amplifier category belongs to the amplifier IC hierarchy, which includes instrumentation, precision, and general-purpose amplifiers used for signal conditioning, control, and system-level analog processing.

The LM258AWYPT provides two amplifiers in one compact package. Key electrical characteristics include a 1.1 MHz gain-bandwidth product, 600 V/ms slew rate, 55 nV/√Hz noise density at 1 kHz, 85 dB common-mode rejection, and a 700 µA quiescent-current figure. Its operating temperature range of -40°C to +105°C supports industrial environments where consumer-grade amplifiers may be unsuitable.

Each amplifier is internally frequency compensated, allowing stable operation without an external compensation capacitor in the standard closed-loop configurations. The device supports single-supply operation from 3 V to 30 V and dual-supply operation when the mid-supply reference is established appropriately. Its low quiescent current helps limit power consumption in battery-powered and distributed sensing systems.

Typical applications include low-side current measurement, transducer conditioning, industrial sensor interfaces, feedback networks in power-control circuits, audio preamplification, and general buffered analog stages. Two independent amplifiers in one package can also implement a differential amplifier or instrumentation-style front end when suitable resistor networks and component tolerances are used.

For PCB design, keep feedback resistors close to the associated input pins and maintain a low-impedance return path for each amplifier. Avoid long traces between the two amplifier channels when they carry different signals. Confirm output swing, common-mode range, stability, and input protection under the worst-case supply and load conditions before production release.

This product page consolidates the LM258AWYPT electrical characteristics, verified package information, sourcing options, pin mapping, and practical guidance for engineers evaluating this low-power dual operational amplifier.

Alternatives de remplacement direct pour LM258AWYPT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec LM258AWYPT (même facteur de forme et même empreinte) — différant par Amplifier Type, Input Bias Current, Package, Slew Rate, Input Offset Current.

STMicroelectronics
Amplifier Type: General-purpose dual operational amplifier
Input Bias Current: 20 nA
Package: 8-pin SOIC, 0.154 inch body width
Comparer avec LM258AWYPT →
STMicroelectronics
Input Bias Current: 20 nA
Slew Rate: 0.6 V/µs
Comparer avec LM258AWYPT →

LM358AWYPT

✅ Remplacement direct
📦 TSSOP-8
Gain-bandwidth product is 1.1 MHz for both devices, a 0% difference; the orderable temperature grade must be verified before substitution.

📋 Alternative de référence (hors catalogue)

LM258AWYPT Valeurs maximales et caractéristiques électriques

Amplifier Type Dual general-purpose operational amplifier
Number of Amplifiers 2 circuits
Supply Voltage Range 3 V to 30 V
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 1.1 MHz
Slew Rate 600 V/ms
Input Offset Voltage 2 mV
Input Bias Current 2 nA
Input Offset Current 20 nA
Voltage Noise Density 55 nV/√Hz at 1 kHz
Output Current 40 mA
Courant de repos 700 µA
Common-Mode Rejection Ratio 85 dB
Input Offset Voltage Temperature Drift 7 µV/°C
Input Bias Current Temperature Drift 10 pA/°C
Plage de température de fonctionnement -40°C to +105°C
Boîtier TSSOP-8
Type de montage Surface mount
Statut RoHS Compliant

Configuration des broches de LM258AWYPT

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Broche 1 OUT1 — Amplifier 1 output
Broche 2 IN1- — Amplifier 1 inverting input
Broche 3 IN1+ — Amplifier 1 non-inverting input
Broche 4 V- — Negative supply or ground connection
Broche 5 IN2+ — Amplifier 2 non-inverting input
Broche 6 IN2- — Amplifier 2 inverting input
Broche 7 OUT2 — Amplifier 2 output
Broche 8 V+ — Positive supply connection

Applications typiques

LM258AWYPT convient pour 6 applications: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Battery-Powered Remote Sensing, Audio Preamplification, Power-Control Feedback Networks, Data Acquisition and Instrumentation.

🏭

Industrial Sensor Signal Conditioning

The LM258AWYPT is suitable for conditioning resistive, voltage-based, and low-current sensors in industrial equipment. Each internally compensated amplifier can provide non-inverting gain, buffering, or active filtering within its 1.1 MHz gain-bandwidth product. The 85 dB common-mode rejection specification helps reduce corruption when the sensor signal is small relative to the common-mode voltage. With two independent amplifiers in one TSSOP-8 package, designers can pair the sensor amplifier with a filter or output driver. The -40°C to +105°C rating supports industrial environments, although the input common-mode range and output swing must be checked at the minimum 3 V supply.

⚡

Low-Side Current Measurement

The LM258AWYPT can amplify the voltage generated by a low-side current-sense shunt in motor, power-supply, and battery-monitoring systems. The 600 V/ms slew rate allows the amplifier to respond quickly to current transients, while the 55 nV/√Hz noise density at 1 kHz helps preserve small shunt-voltage signals. A differential arrangement can use both amplifiers, although resistor matching determines common-mode rejection in practice. Because the listed common-mode rejection is 85 dB, layout symmetry and precision resistors remain important. The 700 µA quiescent current contributes little overhead in systems where the shunt current is substantially higher.

🧩

Battery-Powered Remote Sensing

The LM258AWYPT is appropriate for low-voltage remote sensor nodes because it operates from a 3 V supply and has a listed 700 µA quiescent current. Two amplifiers can form a non-inverting front end and an active low-pass or level-shifting stage, reducing the component count compared with separate single amplifiers. The -40°C to +105°C range also permits operation in outdoor industrial enclosures where temperature varies substantially. Designers should calculate the complete sleep and active energy budget, including divider current and sensor load, and should disable unused channels or the entire device during long storage periods to reduce leakage losses.

🎧

Audio Preamplification

The LM258AWYPT can provide moderate-gain audio preamplification in small microphone, line-level, and mixer circuits. Its 55 nV/√Hz voltage-noise density at 1 kHz and 1.1 MHz gain-bandwidth product support low-frequency audio stages, while the 600 V/ms slew rate helps avoid excessive distortion on larger transients. The dual configuration can provide two independent mono channels when the circuit layout keeps the channels electrically and physically separate. For microphones requiring substantial gain, input bias current of 2 nA helps preserve source loading behavior. Feedback resistor values should keep closed-loop bandwidth below the amplifier's gain-bandwidth limit and avoid driving capacitive microphone cables directly.

🔧

Power-Control Feedback Networks

The LM258AWYPT can amplify error signals and drive feedback paths in linear power-control systems, including regulated supplies and actuator controllers. Its 30 V maximum supply and 1.1 MHz gain-bandwidth product are useful for systems that require wider loop bandwidth than a very slow precision amplifier provides. The internal frequency compensation simplifies the implementation of conventional voltage-feedback configurations. However, the 40 mA output-current rating must be checked against transient load requirements, and output saturation should be evaluated at the actual load because the usable swing is narrower than the supply rails.

🖥️

Data Acquisition and Instrumentation

The LM258AWYPT is useful in entry-level data-acquisition modules that buffer sensor outputs and interface signals to an ADC. One channel can amplify the selected measurement while the other provides a complementary reference, filter, or output driver. Its 85 dB common-mode rejection and 700 µA quiescent current provide a practical balance for general-purpose instrumentation, while the TSSOP-8 package simplifies compact analog boards. Designers should maintain matched resistor networks for differential measurements, verify the ADC input range, and place the amplifier close to the source to minimize noise pickup before long PCB traces reach the converter.

What is the operating voltage of LM258AWYPT?
The LM258AWYPT operates from 3 V to 30 V. According to the STMicroelectronics LM258 datasheet, this supply range supports both single-supply and dual-supply circuit arrangements. The dual amplifiers are independent, although both share the same supply pins. Designers should verify that every input, output, and feedback node remains within the input common-mode and output-voltage limits under the minimum supply condition.
What are the key specifications of LM258AWYPT that engineers should know?
The LM258AWYPT combines two general-purpose amplifiers in an 8-pin TSSOP package. Its main ratings include a 3 V to 30 V supply range, 1.1 MHz gain-bandwidth product, 600 V/ms slew rate, 700 µA quiescent current, 55 nV/√Hz noise density at 1 kHz, and an operating-temperature range of -40°C to +105°C. According to the STMicroelectronics LM258 datasheet, these characteristics make it suitable for low-power industrial analog conditioning.
Where can I download the LM258AWYPT datasheet PDF?
The LM258AWYPT datasheet PDF is available through the datasheet link on this product page, with an additional manufacturer sales listing available from STMicroelectronics. The document contains the electrical characteristics, application information, and package details. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and when confirming the common 8-pin dual-operational-amplifier connection.
Where can I find the LM258AWYPT pinout?
The LM258AWYPT uses the standard 8-pin TSSOP dual-operational-amplifier arrangement. Pins 1 and 7 are the two outputs, pins 2 and 6 are the inverting inputs, pins 3 and 5 are the non-inverting inputs, pin 4 is ground, and pin 8 is the positive supply. According to the STMicroelectronics LM258 datasheet, use the package drawing and pin table to confirm orientation before PCB assembly.
Is LM258AWYPT suitable for industrial sensor conditioning?
Yes, the LM258AWYPT is suitable for industrial sensor conditioning because it combines a -40°C to +105°C operating range with low 700 µA quiescent current and two amplifiers per package. According to the STMicroelectronics LM258 datasheet, its 85 dB common-mode rejection and 1.1 MHz gain-bandwidth product support low-frequency bridge, current-sense, and buffered sensor signals. Input common-mode and output swing still require checking for each sensor excitation level.
How does LM258AWYPT compare with LM358AWYPT?
LM258AWYPT and LM358AWYPT are members of the same dual general-purpose operational-amplifier family and appear in a direct product comparison. The target LM258AWYPT is specified for a -40°C to +105°C range, 1.1 MHz gain-bandwidth product, and 30 V maximum supply, while the alternative listing identifies LM358AWYPT as the same 8-TSSOP class. According to the manufacturer family documentation, the exact orderable temperature grade should be checked before substitution.
What is the best drop-in replacement for LM258AWYPT?
LM358AWYPT is the closest documented same-package candidate for the LM258AWYPT. It uses an 8-pin TSSOP package and belongs to the same dual general-purpose operational-amplifier family, with a listed gain-bandwidth product of 1.1 MHz, matching the target's 1.1 MHz rating. Before replacing the component, verify the operating-temperature grade, offset voltage, input bias current, and electrical limits in the manufacturer datasheet.
What can replace LM258AWYPT?
LM358AWYPT can serve as a documented drop-in candidate when its temperature grade and electrical characteristics satisfy the design. Both devices use an 8-pin TSSOP package and are identified as low-power dual general-purpose operational amplifiers with a 1.1 MHz gain-bandwidth product. According to the relevant manufacturer family documentation, confirm pin orientation and all worst-case specifications, particularly input offset, common-mode range, and operating temperature.
Is LM258AWYPT the same as LM358AWYPT?
No, the LM258AWYPT and LM358AWYPT are related orderable variants rather than identical part numbers. The target LM258AWYPT has a stated operating range of -40°C to +105°C, 3 V to 30 V supply, and 1.1 MHz gain-bandwidth product. According to the manufacturer family documentation, LM358AWYPT is a same-package alternative, but its specific temperature and parametric grades must be checked before treating it as equivalent.
When should I choose LM258AWYPT over LM358AWYPT?
Choose LM258AWYPT when the design needs its stated -40°C to +105°C operating range and low-power dual-amplifier performance in an 8-pin TSSOP package. LM358AWYPT is attractive for a second-source or family-related configuration when its manufacturer-rated temperature grade covers the application. According to the STMicroelectronics family documentation, compare worst-case offset voltage, input bias current, common-mode rejection, and output swing before finalizing the choice.
Is LM258AWYPT suitable for battery-powered instrumentation?
Yes, the LM258AWYPT is suitable for many low-power battery-operated instrumentation stages. Its specified quiescent current is 700 µA, and its operation begins at a 3 V supply, which supports low-voltage sensing systems. According to the STMicroelectronics LM258 datasheet, total battery demand still includes load current, divider current, and both amplifier channels. Use shutdown or a control-gated power path when long-term standby energy dominates the design.
How should I design the PCB layout for LM258AWYPT?
Place each amplifier's feedback resistors close to its pins and keep input traces short to reduce parasitic pickup and feedback from adjacent channels. Route supply and ground returns to provide low-impedance paths for the 700 µA bias current plus load current. According to the STMicroelectronics LM258 datasheet, the internal compensation supports standard closed-loop use, but board-level coupling still requires careful grounding and separation between high-impedance inputs and switching nodes.
Where can I buy LM258AWYPT online?
Use the Request a Quote form on this page to request LM258AWYPT availability, packaging, and current lead time from XAIPART. The manufacturer also offers a direct product listing for this low-power dual operational amplifier. Quote requests allow the exact 8-pin TSSOP orderable code to be matched with the required quantity and delivery schedule.
What is the price of LM258AWYPT?
The current price of LM258AWYPT should be requested through the Request a Quote form on this page so it can be matched to quantity, packaging, and delivery requirements. The device is identified as a low-power dual operational amplifier in an 8-pin TSSOP package. Commercial availability and lead time can change, so use the quote form rather than relying on an outdated listing value.
What is the lead time and stock status for LM258AWYPT?
Current stock and lead time for LM258AWYPT should be confirmed through the Request a Quote form on this page. Submit the required quantity, reel or tray packaging preference, and destination so the order can be evaluated against current supply. The 8-pin TSSOP package and dual-amplifier configuration are confirmed by the manufacturer product listing.

Données de référence d'ingénierie pour LM258AWYPT — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the LM258AWYPT for low-power, general-purpose dual-amplifier designs that need a 3 V to 30 V supply, a 1.1 MHz gain-bandwidth product, and operation from -40°C to +105°C. It is particularly useful for industrial sensor conditioning, low-side current measurement, battery-operated instrumentation, and compact analog interfaces where two amplifiers share one TSSOP-8 package. LM358AWYPT is the closest documented same-package alternative when its temperature grade and worst-case electrical limits meet the requirements. Do not select it solely from the shared package: compare input offset voltage, input bias current, common-mode rejection, output swing, and quiescent current in the manufacturer documentation. For designs requiring substantially lower offset, lower noise, faster slew rate, rail-to-rail output, or greater output current, choose a precision or modern general-purpose amplifier rather than treating either part as a universal replacement.

Comparaison avec les alternatives

Paramètre Ce produit LM358AWYPT
Brand STMicroelectronics STMicroelectronics
Package TSSOP-8 TSSOP-8
Amplifier Configuration Dual Dual
Product Class Low-power general-purpose operational amplifier Low-power general-purpose operational amplifier
Gain-Bandwidth Product 1.1 MHz 1.1 MHz

Principaux différenciateurs

  • Specified for extended industrial temperature operation (vs LM358AWYPT)
  • Wide single-supply operating range (vs LM358AWYPT)
  • Two amplifiers in a compact TSSOP-8 package (vs LM358AWYPT)

Notes de conception

Place the feedback resistors directly beside the relevant LM258AWYPT input and output pins. For high-impedance sources, keep input traces short, avoid routing them parallel to switching-node copper, and provide a quiet ground return. If both channels process independent signals, maintain physical separation to reduce capacitive coupling. Pin 8 should have a short, low-impedance supply path, while pin 4 should connect to the system ground plane or the negative supply in a dual-supply arrangement.

Use resistor ratios that keep the closed-loop bandwidth safely below the 1.1 MHz gain-bandwidth product. A practical rule is to compare the selected closed-loop gain with the amplifier's gain-bandwidth product and verify phase margin using the manufacturer's stability guidance. Account for parasitic capacitance when driving long cables or ADC sample-and-hold inputs. The 55 nV/√Hz noise density is useful for signal-chain planning, but resistor thermal noise and layout leakage can become important when working with high source impedances.

Do not assume that the full 3 V to 30 V supply range permits equal input and output swings. Check the input common-mode range and output swing at the lowest supply voltage, particularly when using the device at 3 V or with loads near the listed 40 mA rating. Also verify that dual-supply operation uses pin 4 as the negative supply rather than grounding it, and that input voltages remain within the absolute maximum ratings during power-down. Add input protection when transients can exceed the operating range.

Informations de conformité

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The component listing identifies LM258AWYPT as RoHS compliant. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was provided for this orderable code.

Données vérifiées le : 2026-11-20 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

LM258AWYPT datasheet LM258AWYPT pinout LM258AWYPT datasheet pdf LM258AWYPT equivalent LM258AWYPT replacement LM258AWYPT vs LM358AWYPT LM258AWYPT TSSOP-8 footprint LM258AWYPT price LM258AWYPT stock STMicroelectronics LM258AWYPT LM258AWYPT 30V operational amplifier LM258AWYPT industrial sensor application

Composants & termes associés

STMicroelectronics LM258AWYPT LM358AWYPT LM258 dual operational amplifier operational amplifier general-purpose amplifier amplifier IC analog integrated circuit semiconductor low-dropout power consumption gain-bandwidth product slew rate common-mode rejection ratio input bias current input offset voltage voltage noise density quiescent current feedback network TSSOP-8 TSSOP surface-mount package RoHS industrial sensor conditioning battery-powered instrumentation
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ