LM258DRE4 - Dual 30V 700kHz Op Amp | Texas Instruments
Teilenummer: LM258DRE4 ✓ AktivLM258DRE4 Übersicht
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to process signals whose voltage lies above or below its supply rails. In the electronics hierarchy, the LM258 is a general-purpose operational amplifier, a dual amplifier, and ultimately an analog semiconductor. Its internal frequency compensation, common-mode input range that includes ground, and low bias current make it useful for amplifying weak signals without requiring an external compensation network.
The LM258DRE4 combines a 700 kHz gain-bandwidth product with a 0.3 V/µs slew rate, allowing relatively low-frequency control, sensing, and buffering functions to be handled without an external compensation network. Typical input offset voltage is 3 mV, while typical input offset current is 2 nA and typical input bias current is 20 nA. The device also accepts differential input voltages up to 32 V, although the 30 V maximum supply rating remains the governing operating limit.
Both amplifier channels share the same pinout and common supply connections, allowing one IC to implement two related signal-processing functions. The SOIC-8 construction uses gull-wing leads and supports conventional surface-mount assembly. Because the amplifiers are not rail-to-rail output devices, output swing and common-mode behavior must be checked against the selected supply voltages and load. Input-referred offset and bias characteristics are especially important when the source impedance is high or when precision DC measurements are required.
Typical LM258DRE4 applications include industrial sensor conditioning, low-frequency active filters, audio preamplifier stages, voltage-controlled amplifiers, relay-driver interfaces, and general-purpose DC signal amplification. The 30 V capability accommodates 24 V industrial systems when the signal and supply voltages remain within the device limits. The low 0.7 mA typical supply-current drain is useful where multiple amplifier channels must operate continuously within a limited power budget.
The principal design trade-off is its 700 kHz bandwidth: this is ample for many sensor, control, and audio tasks but too slow for high-speed instrumentation or communications waveforms. Input bias current of 20 nA typical can create offset errors across high source impedances, and the 3 mV typical input offset should be included in overall accuracy budgets. Decoupling, grounding, and output-load stability must be evaluated using the manufacturer application guidance.
This page consolidates the device specifications, pin assignments, sourcing information, and practical alternatives into an engineering-focused reference. It also distinguishes true package-compatible replacements from parts that merely perform a similar amplifier function, helping designers preserve PCB layout, supply compatibility, and signal-chain performance during obsolescence or second-source evaluation.
Drop-in-Alternativen für LM258DRE4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM258DRE4 (gleiche Bauform und Footprint) – abweichend in Package, Operating Temperature Range.
LM258DR
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM258AD
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM258AYDT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TSH22IDT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TSB7192IDT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM258DRE4 Grenzwerte & elektrische Eigenschaften
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Maximum Supply Voltage | 30 V |
| Single-Supply Operating Range | Up to 26 V |
| Dual-Supply Operating Range | Up to 52 V total |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Typical Supply-Current Drain | 0.7 mA |
| Betriebstemperaturbereich | -25°C to +85°C |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 20 nA |
| Maximum Differential Input Voltage | 32 V |
| Common-Mode Input Range | Includes ground |
| Gehäuse | 8-SOIC, 3.90 mm body width |
| Montageart | Surface mount |
| Shipping Package | Tape and reel |
LM258DRE4 Pin-Konfiguration
| Pin 1 | OUTA — Amplifier A output |
| Pin 2 | INA- — Inverting input for amplifier A |
| Pin 3 | INA+ — Non-inverting input for amplifier A |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | INB+ — Non-inverting input for amplifier B |
| Pin 6 | INB- — Inverting input for amplifier B |
| Pin 7 | OUTB — Amplifier B output |
| Pin 8 | V+ — Positive supply connection |
Typische Anwendungen
LM258DRE4 ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffer, Active Filtering and Control Loops, Power Supply Monitoring, Data Acquisition Front End, Automotive and Heavy Equipment Interface.
Industrial Sensor Signal Conditioning
The LM258DRE4 is suitable for amplifying low-level outputs from industrial temperature, pressure, and position sensors. Its 700 kHz gain-bandwidth product provides ample bandwidth for many externally filtered sensor channels, while the common-mode input range includes ground supports signals referenced close to the lower supply rail. A typical conditioning stage can use one channel for gain and the second for buffering or active filtering. The main accuracy consideration is the 3 mV typical input offset, which should be included in the sensor error budget, while the 20 nA typical bias current matters when the source impedance is high.
Empfohlen
Audio Preamplifier and Buffer
The LM258DRE4 can provide gain and impedance buffering in modest audio and communication paths. Its 0.3 V/µs slew rate and 700 kHz bandwidth cover low-frequency program-audio and control-signal applications, and the dual layout allows one channel to amplify a signal while the other buffers the result. The device is not a rail-to-rail amplifier, so the output swing must remain within the usable region of the selected supply. Its 3 mV typical offset may also be audible in very low-noise stages, making additional filtering or a higher-precision amplifier preferable for demanding hi-fi designs.
Empfohlen
Active Filtering and Control Loops
The internally compensated LM258DRE4 is useful in first- and second-order low-frequency active filters, integrators, and control loops. Its 700 kHz gain-bandwidth product permits useful closed-loop gain at frequencies well below the device limit, while the typical 0.7 mA supply-current drain supports continuously powered equipment. Stable operation with the capacitive loads encountered in filtering and cable-driven stages must be checked against the manufacturer guidance. Designers should also avoid operating too close to the supply rails because the output does not swing fully rail-to-rail.
Empfohlen
Power Supply Monitoring
The LM258DRE4 can monitor a 24 V industrial supply or generate an analog control signal by comparing a divided feedback voltage with a reference. The 30 V maximum supply rating provides useful margin in nominal 24 V systems when transient and tolerance limits are controlled. One channel performs the comparison function while the second amplifies or buffers the result for an ADC or actuator interface. Because the device is not a precision comparator, offset voltage and drift directly affect threshold accuracy; for high-resolution monitoring, use a low-offset amplifier or comparator with a defined input range.
Empfohlen
Data Acquisition Front End
The dual LM258DRE4 channels can condition two low-frequency inputs in a compact data-acquisition module. The 700 kHz bandwidth suits sensor signals after anti-alias filtering, and the common-mode input range including ground simplifies systems with bipolar sensor outputs biased around the lower rail. The internal frequency compensation reduces external component count for basic non-inverting and inverting stages. Accuracy limits must be managed by accounting for 3 mV typical input offset, 2 nA typical offset current, and 20 nA typical bias current, especially when multiplexer impedance and cable leakage vary between channels.
Empfohlen
Automotive and Heavy Equipment Interface
The LM258DRE4 can implement low-frequency interface functions in heavy equipment and automotive electronic systems when the specific operating environment is within the device rating. Its 30 V supply capability is useful for systems connected to 24 V electrical environments, and the 700 kHz bandwidth is sufficient for many sensor and actuator conditioning channels. The standard LM258DRE4 ordering code should not be assumed to be AEC-Q100 qualified. Automotive programs must select an explicitly qualified orderable part, verify the −25°C to +85°C grade against the system requirement, and apply the manufacturer’s transient and protection guidance.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM258DRE4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM258DR | LM258AD | LM258AYDT | TSH22IDT | TSB7192IDT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | SO-8 - same | SO-8 - same |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
Wichtigste Unterscheidungsmerkmale
- Established dual LM258 electrical platform in a standard 8-SOIC footprint (vs. TSH22IDT)
- Low typical supply-current drain for a dual high-voltage amplifier (vs. LM258AYDT)
- Higher specified gain-bandwidth product than the low-speed reference point (vs. LM258DR)
Designhinweise
The LM258DRE4 can operate from a single supply up to 26 V or a dual supply totaling 52 V, but the absolute maximum supply rating is 30 V. Do not treat the 52 V dual-supply figure as a 52 V rail-to-rail operating condition. Place the positive supply bypass capacitor close to pin 8 and the negative bypass capacitor close to pin 4. For single-supply operation, connect V- to the ground reference and verify that input and output voltages remain inside the linear operating range rather than assuming rail-to-rail behavior.
Input bias and offset errors can dominate high-impedance sensor designs. The LM258DRE4 has 3 mV typical input offset voltage, 2 nA typical offset current, and 20 nA typical input bias current. Estimate the bias-current contribution with the formula VERROR = IB × RSOURCE and include resistor and sensor tolerance in the overall error budget. If the calculated error is too large, reduce the source impedance, use a lower-bias-current amplifier, or add a low-offset instrumentation stage.
Treat the two amplifier channels as electrically similar but keep each channel’s feedback network and input routing compact. Place input and feedback components adjacent to their associated pins, maintain a low-impedance ground return for pin 4, and avoid routing high-impedance input traces beside supply and digital return paths. The 8-SOIC footprint is standard and compatible across the listed alternatives, but verify the exact pinout of every cross-brand candidate before releasing a substitution.
The LM258 is a general-purpose, non-rail-to-rail amplifier, so output swing and common-mode limits constrain its usable voltage range. Do not design the output to reach the positive or negative rail, and do not assume inputs can move above V+ or below the usable common-mode boundary. The 700 kHz gain-bandwidth product also limits closed-loop bandwidth as gain increases. Check the manufacturer performance curves for the intended gain, output load, supply voltage, and temperature before finalizing the analog front end.
Compliance-Informationen
The standard LM258DRE4 ordering code is not identified as AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer’s current product or material-compliance documentation.