LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments
Teilenummer: LM2904PWRG4-JF ✓ AktivLM2904PWRG4-JF Übersicht
An operational amplifier is a high-gain analog building block used in signal-conditioning, comparison, feedback, filtering, and amplification circuits. In the broader electronics hierarchy, an operational amplifier is a type of analog amplifier IC and belongs to the amplifier and signal-processing category. A dual device contains two amplifier sections in one package, allowing one component to handle two related signals while reducing board area and external component count.
The LM2904 family is positioned for general-purpose designs rather than precision or high-speed instrumentation. Its stated 700 kHz gain-bandwidth product gives designers a concrete basis for estimating closed-loop bandwidth at a selected noise gain. The 26 V maximum supply rating provides compatibility with higher-voltage analog systems, while the -40°C to +125°C temperature range supports industrial temperature-range design requirements.
Each amplifier can operate with feedback configured for inverting, non-inverting, summing, and other standard analog topologies. Differential input and feedback arrangements determine voltage gain and signal behavior, so the same device can serve as a signal amplifier, comparator when configured for saturation, or an active filter building block. The dual channel count is especially useful when a circuit requires two closely related signal paths, such as a sensor front end and a buffered reference stage.
Typical applications include sensor-signal conditioning, control-loop error amplification, audio preamplification, low-frequency active filtering, and general instrumentation. The 700 kHz gain-bandwidth product is most relevant to low-to-moderate-bandwidth closed-loop designs, while the 26 V supply rating is useful when the signal path operates from a higher-voltage rail.
Design the surrounding feedback network carefully because resistor and capacitor tolerances directly influence gain, bandwidth, offset behavior, and stability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they do not float. The TSSOP-8 outline also requires adequate solder-joint formation and thermal spreading for reliable assembly.
This product page combines the exact ordering information, principal electrical ratings, package details, drop-in replacement guidance, comparison rows, and application-specific design considerations to support faster component selection and board planning.
Drop-in-Alternativen für LM2904PWRG4-JF – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2904PWRG4-JF (gleiche Bauform und Footprint) – abweichend in Package.
LM2904PWRG4
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2904PWRG4-Q1
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LM2904BPWRG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM2904BAPWRG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM2904PWRG4-JF Grenzwerte & elektrische Eigenschaften
| Amplifier Count | 2 circuits |
| Product Type | Standard general-purpose operational amplifier |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Gehäuse | TSSOP-8 (PW) |
| Pin-Anzahl | 8 pins |
| Betriebstemperaturbereich | -40°C to +125°C |
| Montageart | Surface mount |
| Channel Architecture | Dual |
LM2904PWRG4-JF tssop-8 (pw) Pinbelegungsleitfaden
Pinbelegung für LM2904PWRG4-JF (tssop-8 (pw)-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM2904PWRG4-JF.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM2904PWRG4-JF ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Control-System Error Amplifier, Audio Preamplifier, Active Filter and Integrator, Precision Measurement Front End, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The Texas Instruments LM2904PWRG4-JF is useful when a sensor output must be amplified before conversion or control processing. Its two amplifier channels can support an inverting or non-inverting front end and a second buffer or reference stage without using two separate packages. The 700 kHz gain-bandwidth product supports low-to-moderate-bandwidth sensors, while the -40°C to +125°C range covers demanding industrial environments. Confirm that the sensor output remains inside the input common-mode range and check the complete datasheet for bias-current, offset, and output-swing requirements.
Empfohlen
Control-System Error Amplifier
The LM2904PWRG4-JF can implement the forward error amplifier in a feedback control loop where a 700 kHz gain-bandwidth product and 26 V maximum supply are adequate. One channel may compare a feedback signal with a reference, while the other can amplify a plant or compensation path. The dual package reduces board area, and the -40°C to +125°C rating supports industrial operating conditions. Stability must be evaluated with the actual feedback network, load, and compensation components rather than inferred from gain-bandwidth alone.
Empfohlen
Audio Preamplifier
The LM2904PWRG4-JF can serve as a general-purpose preamplifier for audio signals within its bandwidth and output-swing limits. Its dual architecture allows one channel to amplify a source while the other drives or buffers a related signal. The stated 700 kHz gain-bandwidth product covers many low-frequency audio-preamplification paths, and the 26 V supply rating accommodates higher-voltage analog rails. Check input offset, bias current, noise, output swing, and stability in the manufacturer datasheet before setting the closed-loop gain.
Empfohlen
Active Filter and Integrator
The dual LM2904PWRG4-JF can implement active filters, integrators, or waveform-shaping stages in measurement and control equipment. The 700 kHz gain-bandwidth product provides a defined upper limit for closed-loop response, while the 8-pin TSSOP package supports compact analog boards. Component tolerances and the op amp's finite gain and output-current capability determine practical filter accuracy. Prototype the selected topology and verify phase margin, output swing, and stability across the required frequency range.
Empfohlen
Precision Measurement Front End
The LM2904PWRG4-JF can provide differential or single-ended amplification in a measurement front end when the required bandwidth remains within its 700 kHz gain-bandwidth product. Two channels are useful for amplifying a sensor and a reference or for implementing active differential subtraction. The 26 V supply rating and -40°C to +125°C operating range support higher-voltage industrial instrumentation, but the part is characterized as general purpose rather than a dedicated precision amplifier. Validate offset, drift, noise, and common-mode performance against the measurement accuracy budget.
Empfohlen
Portable Instrumentation
The LM2904PWRG4-JF is suitable for compact, low-to-moderate-bandwidth instrumentation requiring two general-purpose analog channels. Its TSSOP-8 package helps reduce PCB footprint, and the 700 kHz gain-bandwidth product is appropriate for many sensor and interface signals. The -40°C to +125°C rating provides design flexibility across industrial temperature ranges. Supply voltage, quiescent current, input bias current, and output capability should be checked together because a compact portable design can be constrained by power and thermal limits.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2904PWRG4-JF – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2904PWRG4 | LM2904PWRG4-Q1 | LM2904BPWRG4 | LM2904BAPWRG4 |
|---|---|---|---|---|---|
| Package | TSSOP-8 (PW) | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 26 V | 26 V | 26 V | 26 V | 26 V |
| Gain-Bandwidth Product | 700 kHz | 700 kHz | 700 kHz | 700 kHz | 700 kHz |
| Amplifier Count | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Pin Count | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Functionality Variant | Standard LM2904 family | Standard family ordering form | Automotive-qualified family option | Upgraded-functionality family member | Upgraded-functionality family member |
Wichtigste Unterscheidungsmerkmale
- Matches the established LM2904 electrical envelope (vs. LM2904BPWRG4)
- Supports automotive-qualified sourcing when the -Q1 orderable option is appropriate (vs. LM2904PWRG4)
- Compact dual-channel implementation (vs. MC3403DR)
Designhinweise
Place the input and output bypass capacitors close to the corresponding TSSOP-8 power and ground pins, and keep the feedback-resistor paths short. The compact package leaves little room for long copper traces, which can increase coupling into a high-impedance input. Use a ground plane with a direct return path and avoid routing sensitive input nodes beneath digital or switching-supply sections of the board.
Do not infer the usable input range from the 26 V maximum supply rating alone. Check the complete datasheet for input common-mode limits, output-swing limits, and differential-input restrictions. Also avoid leaving either amplifier input floating; terminate each unused channel in a configuration that provides a defined DC bias and prevents unintended oscillation or output saturation.
The 700 kHz gain-bandwidth product means that closed-loop bandwidth changes with the selected noise gain. Account for feedback-network impedance, load capacitance, and amplifier output-current capability when working near the upper bandwidth limit. Breadboard the completed topology, measure gain and phase, and add compensation or a lower bandwidth setting if the intended feedback network produces inadequate stability margin.
The TSSOP-8 package is small, so the actual dissipation and solder-joint condition determine the allowable operating temperature. The family rating extends to +125°C, but that does not guarantee every board can reach the upper limit at maximum supply voltage and output current. Validate the worst-case supply differential, load, ambient temperature, copper area, and nearby heat sources before treating the temperature rating as a guaranteed system capability.
Compliance-Informationen
The manufacturer product page identifies the ordering configuration and electrical ratings, but the cited material does not state the requested compliance or material-category results.