LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments
料号: LM2904PWRG4-JF ✓ 量产中LM2904PWRG4-JF 概述
An operational amplifier is a high-gain analog building block used in signal-conditioning, comparison, feedback, filtering, and amplification circuits. In the broader electronics hierarchy, an operational amplifier is a type of analog amplifier IC and belongs to the amplifier and signal-processing category. A dual device contains two amplifier sections in one package, allowing one component to handle two related signals while reducing board area and external component count.
The LM2904 family is positioned for general-purpose designs rather than precision or high-speed instrumentation. Its stated 700 kHz gain-bandwidth product gives designers a concrete basis for estimating closed-loop bandwidth at a selected noise gain. The 26 V maximum supply rating provides compatibility with higher-voltage analog systems, while the -40°C to +125°C temperature range supports industrial temperature-range design requirements.
Each amplifier can operate with feedback configured for inverting, non-inverting, summing, and other standard analog topologies. Differential input and feedback arrangements determine voltage gain and signal behavior, so the same device can serve as a signal amplifier, comparator when configured for saturation, or an active filter building block. The dual channel count is especially useful when a circuit requires two closely related signal paths, such as a sensor front end and a buffered reference stage.
Typical applications include sensor-signal conditioning, control-loop error amplification, audio preamplification, low-frequency active filtering, and general instrumentation. The 700 kHz gain-bandwidth product is most relevant to low-to-moderate-bandwidth closed-loop designs, while the 26 V supply rating is useful when the signal path operates from a higher-voltage rail.
Design the surrounding feedback network carefully because resistor and capacitor tolerances directly influence gain, bandwidth, offset behavior, and stability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they do not float. The TSSOP-8 outline also requires adequate solder-joint formation and thermal spreading for reliable assembly.
This product page combines the exact ordering information, principal electrical ratings, package details, drop-in replacement guidance, comparison rows, and application-specific design considerations to support faster component selection and board planning.
直接替换替代料: LM2904PWRG4-JF ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904PWRG4-JF (相同外形与封装尺寸) ——差异在于 Package.
LM2904PWRG4
✅ 直接替换联系询价
查看数据手册 →LM2904PWRG4-Q1
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2904BPWRG4
✅ 直接替换📋 参考替代料(不在目录中)
LM2904BAPWRG4
✅ 直接替换📋 参考替代料(不在目录中)
LM2904PWRG4-JF 最大额定值与电气特性
| Amplifier Count | 2 circuits |
| Product Type | Standard general-purpose operational amplifier |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| 封装 | TSSOP-8 (PW) |
| 引脚数量 | 8 pins |
| 工作温度范围 | -40°C to +125°C |
| 安装类型 | Surface mount |
| Channel Architecture | Dual |
LM2904PWRG4-JF tssop-8 (pw) 引脚配置指南
LM2904PWRG4-JF(tssop-8 (pw) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2904PWRG4-JF.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2904PWRG4-JF 适用于 6 应用s: Industrial Sensor Signal Conditioning, Control-System Error Amplifier, Audio Preamplifier, Active Filter and Integrator, Precision Measurement Front End, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The Texas Instruments LM2904PWRG4-JF is useful when a sensor output must be amplified before conversion or control processing. Its two amplifier channels can support an inverting or non-inverting front end and a second buffer or reference stage without using two separate packages. The 700 kHz gain-bandwidth product supports low-to-moderate-bandwidth sensors, while the -40°C to +125°C range covers demanding industrial environments. Confirm that the sensor output remains inside the input common-mode range and check the complete datasheet for bias-current, offset, and output-swing requirements.
推荐
Control-System Error Amplifier
The LM2904PWRG4-JF can implement the forward error amplifier in a feedback control loop where a 700 kHz gain-bandwidth product and 26 V maximum supply are adequate. One channel may compare a feedback signal with a reference, while the other can amplify a plant or compensation path. The dual package reduces board area, and the -40°C to +125°C rating supports industrial operating conditions. Stability must be evaluated with the actual feedback network, load, and compensation components rather than inferred from gain-bandwidth alone.
推荐
Audio Preamplifier
The LM2904PWRG4-JF can serve as a general-purpose preamplifier for audio signals within its bandwidth and output-swing limits. Its dual architecture allows one channel to amplify a source while the other drives or buffers a related signal. The stated 700 kHz gain-bandwidth product covers many low-frequency audio-preamplification paths, and the 26 V supply rating accommodates higher-voltage analog rails. Check input offset, bias current, noise, output swing, and stability in the manufacturer datasheet before setting the closed-loop gain.
推荐
Active Filter and Integrator
The dual LM2904PWRG4-JF can implement active filters, integrators, or waveform-shaping stages in measurement and control equipment. The 700 kHz gain-bandwidth product provides a defined upper limit for closed-loop response, while the 8-pin TSSOP package supports compact analog boards. Component tolerances and the op amp's finite gain and output-current capability determine practical filter accuracy. Prototype the selected topology and verify phase margin, output swing, and stability across the required frequency range.
推荐
Precision Measurement Front End
The LM2904PWRG4-JF can provide differential or single-ended amplification in a measurement front end when the required bandwidth remains within its 700 kHz gain-bandwidth product. Two channels are useful for amplifying a sensor and a reference or for implementing active differential subtraction. The 26 V supply rating and -40°C to +125°C operating range support higher-voltage industrial instrumentation, but the part is characterized as general purpose rather than a dedicated precision amplifier. Validate offset, drift, noise, and common-mode performance against the measurement accuracy budget.
推荐
Portable Instrumentation
The LM2904PWRG4-JF is suitable for compact, low-to-moderate-bandwidth instrumentation requiring two general-purpose analog channels. Its TSSOP-8 package helps reduce PCB footprint, and the 700 kHz gain-bandwidth product is appropriate for many sensor and interface signals. The -40°C to +125°C rating provides design flexibility across industrial temperature ranges. Supply voltage, quiescent current, input bias current, and output capability should be checked together because a compact portable design can be constrained by power and thermal limits.
推荐
推荐产品汇总
工程参考数据: LM2904PWRG4-JF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904PWRG4 | LM2904PWRG4-Q1 | LM2904BPWRG4 | LM2904BAPWRG4 |
|---|---|---|---|---|---|
| Package | TSSOP-8 (PW) | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 26 V | 26 V | 26 V | 26 V | 26 V |
| Gain-Bandwidth Product | 700 kHz | 700 kHz | 700 kHz | 700 kHz | 700 kHz |
| Amplifier Count | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Pin Count | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Functionality Variant | Standard LM2904 family | Standard family ordering form | Automotive-qualified family option | Upgraded-functionality family member | Upgraded-functionality family member |
关键差异点
- Matches the established LM2904 electrical envelope (对比 LM2904BPWRG4)
- Supports automotive-qualified sourcing when the -Q1 orderable option is appropriate (对比 LM2904PWRG4)
- Compact dual-channel implementation (对比 MC3403DR)
设计说明
Place the input and output bypass capacitors close to the corresponding TSSOP-8 power and ground pins, and keep the feedback-resistor paths short. The compact package leaves little room for long copper traces, which can increase coupling into a high-impedance input. Use a ground plane with a direct return path and avoid routing sensitive input nodes beneath digital or switching-supply sections of the board.
Do not infer the usable input range from the 26 V maximum supply rating alone. Check the complete datasheet for input common-mode limits, output-swing limits, and differential-input restrictions. Also avoid leaving either amplifier input floating; terminate each unused channel in a configuration that provides a defined DC bias and prevents unintended oscillation or output saturation.
The 700 kHz gain-bandwidth product means that closed-loop bandwidth changes with the selected noise gain. Account for feedback-network impedance, load capacitance, and amplifier output-current capability when working near the upper bandwidth limit. Breadboard the completed topology, measure gain and phase, and add compensation or a lower bandwidth setting if the intended feedback network produces inadequate stability margin.
The TSSOP-8 package is small, so the actual dissipation and solder-joint condition determine the allowable operating temperature. The family rating extends to +125°C, but that does not guarantee every board can reach the upper limit at maximum supply voltage and output current. Validate the worst-case supply differential, load, ambient temperature, copper area, and nearby heat sources before treating the temperature rating as a guaranteed system capability.
合规信息
The manufacturer product page identifies the ordering configuration and electrical ratings, but the cited material does not state the requested compliance or material-category results.