LM393TLX/NOPB - Dual 36V Comparator | Texas Instruments
Teilenummer: LM393TLX/NOPB ✓ AktivLM393TLX/NOPB Übersicht
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a selected threshold. The LM393 belongs to the comparator hierarchy within the broader semiconductor and signal-conditioning categories. Its open-collector outputs can sink current while remaining in a high-impedance state when inactive, making the device useful for wired logic interfaces, threshold detection, and systems that require an external pull-up resistor.
The LM393 provides two independent comparator elements in one package. Rail-to-rail input operation extends the usable common-mode input range toward the supply rails, while the 2 V to 36 V operating range supports low-voltage logic and higher-voltage industrial systems. Open-collector outputs support wired-AND operation and interface compatibility with CMOS, DTL, ECL, MOS, and TTL logic families. The low 250 nA input bias current reduces disturbance in high-impedance sensing circuits.
Each channel compares an inverting input with a non-inverting input. The output transistor turns on when the non-inverting input is above the inverting input, subject to the comparator's specified offset and response characteristics. Because the output is open collector, an external pull-up resistor establishes the inactive logic level. This architecture adds a passive pull-up component but offers flexibility for wired logic, level translation, and relay-driving arrangements.
Typical uses include monitoring a sensor against a reference voltage, detecting battery or power-supply thresholds, checking overvoltage and undervoltage conditions, and generating a digital status signal from an analog control loop. Industrial equipment, battery-powered systems, automotive-style monitoring circuits, and general-purpose logic interfaces can also use the two channels independently.
Design the open-collector output with a pull-up resistor sized for the required sink current, rise time, and logic-family current. Keep the comparator inputs short and place them away from switching nodes and sources of high-current return paths. Confirm that the input and output currents remain within their specified limits and that the selected pull-up voltage is appropriate for the downstream logic.
This product page combines manufacturer specifications, package information, application guidance, comparison parameters, and practical design considerations to support component selection and PCB implementation. It also identifies the limits of publicly documented drop-in substitution for this exact 8-DSBGA ordering configuration.
Drop-in-Alternativen für LM393TLX/NOPB – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM393TLX/NOPB (gleiche Bauform und Footprint) – abweichend in Output Type, Package.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernLM393TLX/NOPB Grenzwerte & elektrische Eigenschaften
| Comparator Type | General-purpose differential comparator |
| Number of Elements | 2 |
| Supply Voltage Range | 2 V to 36 V |
| Dual Supply Voltage Range | ±1 V to ±18 V |
| Input Common-Mode Range | Rail-to-rail |
| Ausgangstyp | Open-collector |
| Compatible Logic Levels | CMOS, DTL, ECL, MOS, open-collector, and TTL |
| Maximum Input Offset Voltage | 2.0 mV |
| Typical Input Offset Voltage | 5 mV |
| Typical Input Bias Current | 250 nA |
| Typical Response Time | 700 ns |
| Gehäuse | 8-DSBGA |
| Number of Package Balls | 8 balls |
| Ball Pitch | 12 mil |
LM393TLX/NOPB 8 balls Pinbelegungsleitfaden
Pinbelegung für LM393TLX/NOPB (8 balls-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM393TLX/NOPB.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM393TLX/NOPB ist geeignet für 6 Anwendungs: Battery Threshold Monitoring, Industrial Sensor Threshold Detection, Power-Supply Overvoltage Detection, Wired-Logic Interface, Relay and Solenoid Interface, Consumer and Automotive-Style Status Monitoring.
Battery Threshold Monitoring
The LM393TLX/NOPB fits battery-threshold monitoring because its two independent channels can compare a divided battery voltage against a reference while its rail-to-rail input characteristic supports signals near the operating rails. The typical 250 nA input bias current reduces loading on a high-impedance divider, and the 2 V to 36 V supply range supports multiple rail architectures. Each open-collector output can pull down a pull-up node connected to an MCU or fault indicator. The design must keep the input common-mode voltage and absolute maximum limits valid during fast charging, load transients, and overvoltage faults.
Empfohlen
Industrial Sensor Threshold Detection
The LM393TLX/NOPB is appropriate for industrial sensor threshold detection when a slow, low-power decision is sufficient. Its two channels can independently evaluate a sensor signal against a reference, with a maximum offset specification of 2.0 mV and a typical response time of 700 ns. The open-collector output supports a pull-up or a subsequent driver stage, and the 250 nA typical input bias current helps preserve high-impedance sensor signals. Place input routing away from motor, relay, and switching-converter paths, and verify the exact temperature grade for the environmental enclosure.
Empfohlen
Power-Supply Overvoltage Detection
The LM393TLX/NOPB can monitor a power rail for overvoltage or undervoltage conditions by comparing a scaled rail voltage with a reference. Its 2 V to 36 V supply rating and dual-channel architecture allow two thresholds to be implemented without using two packages. The open-collector output can operate a fault latch, host interrupt, or status LED through an external pull-up. Designers should account for output rise time, choose a resistor that respects the sink-current limit, and ensure that startup overshoot or an externally disconnected supply cannot violate the input absolute maximum rating.
Empfohlen
Wired-Logic Interface
The LM393TLX/NOPB is useful in wired-logic systems because each open-collector output can pull a shared node low and support wired-AND behavior. The output stage is compatible with the logic families identified in the LM393 specifications, including CMOS, TTL, MOS, DTL, and ECL families, although the selected pull-up voltage and sink current must be checked against the actual receiver. This arrangement reduces the number of output drivers when several conditions must share one fault line. Use a pull-up that preserves adequate noise margin and keep the bus capacitance low enough to meet the required rising-edge timing.
Empfohlen
Relay and Solenoid Interface
The LM393TLX/NOPB can serve as the decision element in a relay or solenoid interface when its open-collector output drives a suitable transistor stage rather than the inductive load directly. The comparator determines whether an analog control voltage has crossed a threshold, while the downstream transistor supplies the required coil current and isolation from the logic supply. A flyback diode is required across the coil, and the comparator's pull-up resistor must be sized for the transistor's base or gate requirements. Slow response characteristics can also provide intentional noise filtering in some control paths.
Empfohlen
Consumer and Automotive-Style Status Monitoring
The LM393TLX/NOPB fits simple status-monitoring functions in consumer equipment and automotive-style control modules when the electrical and environmental requirements are met. Two independent comparator channels can provide dual-limit detection, mode selection, or fault qualification using low-power open-collector outputs. The wide 2 V to 36 V supply range supports varied system rails, while the small DSBGA package can assist compact layouts. For an automotive-grade deployment, confirm the required qualification and temperature grade explicitly; the commercial ordering designation alone does not establish automotive qualification.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM393TLX/NOPB – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 8-DSBGA |
| Brand | Texas Instruments |
| Comparator Type | General-purpose differential comparator |
| Number of Elements | 2 |
| Supply Voltage Range | 2 V to 36 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Type | Open-collector |
| Maximum Input Offset Voltage | 2.0 mV |
| Typical Input Bias Current | 250 nA |
| Typical Response Time | 700 ns |
Wichtigste Unterscheidungsmerkmale
- Broad supply-voltage operating range (vs. LM393LV)
- Open-collector wired-logic compatibility (vs. Push-pull CMOS comparator alternatives)
- Low 250 nA typical input bias current (vs. LM2903)
Designhinweise
Add an external pull-up resistor to every open-collector output that must drive a high logic state. Choose its resistance from the pull-up voltage, required sink current, receiver input current, bus capacitance, and acceptable rise time. The resistor must remain compatible with the LM393 output sink-current limit under all operating conditions. If the output drives a transistor rather than a logic input, recalculate the base or gate current instead of treating the output as a push-pull driver.
Route the two differential input pairs as short, matched paths where practical, and keep them away from switching nodes, relay coils, and high-current return paths. The open-collector pull-up resistor should be close to the comparator output when the trace is electrically long or capacitive. Because this is an 8-DSBGA device, use the manufacturer's land pattern and ball assignment rather than substituting a generic SOIC-8 footprint; package height and ball pitch must also be checked against enclosure clearance.
Do not assume that a comparator with rail-to-rail inputs can safely accept any voltage between the supply rails. Verify the exact common-mode limits, input absolute maximum ratings, supply sequencing conditions, and output pull-up voltage from the manufacturer datasheet. Also avoid using the suffix LM393TL/NOPB as a drop-in substitute for LM393TLX/NOPB without confirming the manufacturer ordering code, because a suffix change may represent a different shipment form rather than an electrically distinct alternative.
For slow threshold signals, place a suitable capacitor at the input only when its charging behavior will not alter the intended switching threshold or response time. The typical 700 ns response can help reject short disturbances, but very slow signals may also increase propagation delay through the complete detection path. If the open-collector output drives a long or highly capacitive line, use a smaller pull-up value within the sink-current limit and evaluate the resulting rise time and EMI behavior.
Compliance-Informationen
The commercial-grade LM393 family and ordering information are identified by Texas Instruments. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations for LM393TLX/NOPB are not stated on the product overview page. Automotive qualification is not established by this commercial ordering code.