LPC2119FBD64 - 60MHz ARM7 MCU, 128KB Flash | NXP
Teilenummer: LPC2119FBD64 ✓ AktivLPC2119FBD64 Übersicht
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one device. The LPC2100 family belongs to the broader hierarchy of microcontrollers, embedded processors, and embedded semiconductors. It targets applications requiring deterministic control, serial communications, data acquisition, and local real-time processing while keeping component count and board area low.
The LPC2119FBD64 is differentiated by its Arm7TDMI-S core, which supports both 32-bit ARM state and 16-bit Thumb state. Thumb mode can reduce code size for constrained applications, while the 32-bit instruction set remains available for higher-performance routines. Its 128-bit memory interface and accelerator architecture support efficient 32-bit execution at the maximum clock rate. Embedded flash also permits in-system programming and in-application programming.
Peripheral integration is important in embedded systems because it reduces external component requirements. The LPC2119 includes a 10-bit ADC, CAN interface, real-time emulation, embedded trace support, and boundary-scan capability. These features support acquisition, industrial networking, production test, and debug workflows. The manufacturer also documents 64, 128, and 256 KB flash configurations across the LPC2109, LPC2119, and LPC2129 family, with the LPC2119 position corresponding to 128 KB.
Typical uses include industrial control equipment, CAN-connected modules, data loggers, motor and process controllers, and compact embedded platforms requiring 46 GPIO. The 64-LQFP package offers a practical pin count for a mixed-signal controller while keeping the die exposed through a conventional surface-mount footprint.
Board design should preserve the controller's power, decoupling, clock, reset, and programming requirements from the manufacturer datasheet. CAN routing also requires controlled impedance and appropriate termination strategy. Because the public product material does not reproduce the complete pin-description table, use the official LPC2119 documentation when assigning tracks and connector functions.
This product page combines the official NXP device description with package, memory, connectivity, lifecycle, sourcing, replacement, and engineering guidance. It also distinguishes order-code alternatives from genuinely independent drop-in substitutes, helping engineers make a PCB-safe replacement decision rather than assuming that similar specifications guarantee pin compatibility.
Drop-in-Alternativen für LPC2119FBD64 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
LPC2119FBD64/01
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC2119FBD64/01,15
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC2119FBD64/01151
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC2119FBD64/01EL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC2119FBD64 Grenzwerte & elektrische Eigenschaften
| CPU Core | Arm7TDMI-S 16/32-bit RISC |
| Maximum CPU Frequency | 60 MHz |
| Embedded Flash Memory | 128 KB |
| SRAM | 16 KB |
| Program Memory Width | 8 bit |
| Memory Interface Width | 128 bit |
| I/O Lines | 46 lines |
| ADC Resolution | 10 bit |
| CAN Interface | 1 CAN controller |
| Gehäuse | 64-LQFP, 10 x 10 mm |
| Terminal Pitch | 0.50 mm |
| Montageart | Surface Mount |
| Debug Support | Real-time emulation and embedded trace |
| Boundary Scan | Supported |
| Programming Support | ISP and IAP |
LPC2119FBD64 64-lqfp, 10 x 10 mm Pinbelegungsleitfaden
Pinbelegung für LPC2119FBD64 (64-lqfp, 10 x 10 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für LPC2119FBD64.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LPC2119FBD64 ist geeignet für 6 Anwendungs: CAN-Connected Industrial Controller, Embedded Data Logger, Sensor Acquisition and Monitoring, Motor and Process Control, Automotive or Equipment Embedded Platform, Secure Network Appliance Gateway.
CAN-Connected Industrial Controller
The LPC2119FBD64 fits compact industrial control nodes that require deterministic processing and network connectivity without a separate processor. Its 60 MHz Arm7TDMI-S core, 128 KB embedded flash, 16 KB SRAM, and integrated CAN controller provide enough resources for protocol handling, local logic, and supervisory functions. The 64-LQFP package also exposes 46 I/O lines for sensors, actuators, and digital status signals. In implementation, the MCU should drive an appropriate CAN transceiver, use controlled-impedance routing, apply correct bus termination, and include protection suitable for the industrial environment. Real-time emulation and embedded trace support are valuable during commissioning and fault analysis.
Embedded Data Logger
The LPC2119FBD64 is appropriate for a standalone data logger because it combines 128 KB of embedded flash with 16 KB of SRAM, a 10-bit ADC, and 46 general-purpose I/O lines. Firmware can sample analog sensors, timestamp records, apply control logic, and store selected information locally while the flash supports ISP or IAP workflows. The 60 MHz core provides useful headroom for protocol handling and background processing. Designers should choose external nonvolatile storage when logging volume exceeds internal flash, and should account for flash endurance, write wear leveling, data retention, and write-protect strategy in the finished logger.
Sensor Acquisition and Monitoring
The integrated 10-bit ADC makes the LPC2119FBD64 useful for sensor acquisition, condition monitoring, and low-to-moderate-resolution measurement systems. Its 60 MHz processor can service multiple digital inputs, execute control algorithms, and manage communications while the 46 I/O lines support sensors, indicators, and interface signals. The 64-LQFP package provides a practical balance between pin availability and package size. For accurate measurements, the analog signal path should use suitable conditioning and filtering, the ADC reference should remain stable, and grounding should prevent high-current outputs from introducing noise into the analog input and reference network.
Motor and Process Control
The LPC2119FBD64 can serve as the supervisory controller in motor-drive or process-control equipment where 60 MHz execution, 16 KB SRAM, and numerous GPIO are more important than a highly integrated motor-control accelerator. It can accept position or process inputs, execute control sequences, drive discrete outputs, and report status over CAN. Its 128 KB flash also accommodates a bootloader and application firmware. The final design must separate analog power and noisy switching stages from sensitive control signals, include suitable gate-driver protection, and validate timing margins under worst-case load, temperature, and electromagnetic conditions.
Automotive or Equipment Embedded Platform
The LPC2119FBD64 is technically suitable for legacy embedded platforms requiring local flash, CAN connectivity, mixed analog and digital control, and a compact surface-mount package. Its Arm7TDMI-S instruction set remains useful for maintaining established code, while real-time emulation and embedded trace support help diagnose timing-sensitive behavior. Engineers should verify the exact temperature grade, ordering suffix, errata status, and applicable automotive qualification for the chosen order code before using it in a safety- or vehicle-critical function. The 46 GPIO and 10-bit ADC also support body electronics, actuator control, and diagnostic interfaces in established designs.
Secure Network Appliance Gateway
The LPC2119FBD64 can serve as a small protocol-conversion or communications gateway where a dedicated MCU needs local flash and deterministic peripheral handling. Its 128-bit memory interface, accelerator architecture, 128 KB flash, and 16 KB SRAM support efficient 32-bit code execution while the CAN controller and 46 I/O lines provide connectivity. A gateway implementation should keep the MCU outside the primary radio or high-speed network data path unless the selected architecture has been performance-tested. Boot protection, firmware update procedures, watchdog behavior, and secure key storage must be designed into the platform rather than added later.
Technische Referenzdaten für LPC2119FBD64 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LPC2119FBD64/01 | LPC2119FBD64/01,15 | LPC2119FBD64/01151 | LPC2119FBD64/01EL |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) |
Wichtigste Unterscheidungsmerkmale
- Maintains the same documented core and memory configuration (vs. LPC2119FBD64/01)
- Preserves the established 64-LQFP board footprint (vs. LPC2119FBD64/01,15)
- Combines local control and CAN networking (vs. LPC2119FBD64/01151)
- Supports field programming and embedded debugging (vs. LPC2119FBD64/01EL)
Designhinweise
Route the 64-LQFP lands, power inputs, ground connections, clock network, reset circuitry, and debug signals directly from the official NXP pin-description table. Preserve the 0.50 mm terminal pitch and follow the manufacturer's land-pattern dimensions rather than relying on a generic 64-LQFP drawing. Place decoupling capacitors close to the associated supply pins with short, low-loop return paths. Mixed-signal designs should isolate ADC routing from CAN and switching-node returns to reduce coupling into the 10-bit conversion result.
For CAN operation, use a controlled-impedance layer and route the bus as a differential pair with consistent geometry and minimal stubs. Locate the CAN transceiver close to the connector or protected bus interface, and follow its recommended termination arrangement so the inactive-stub behavior remains acceptable in both network states. Keep the controller pins away from switching power stages and high-current return paths. Validate the completed layout for crosstalk, ground discontinuities, ESD routing, and connector-to-transceiver surge current.
Design the supply network for the exact LPC2119FBD64 ordering code using the manufacturer's operating and electrical limits. The device integrates multiple digital and analog functions, so stable rails and local decoupling are essential for reliable clocking, flash access, ADC measurement, and CAN operation. Keep the analog supply and ADC reference paths free from switching-node noise. Check startup sequencing, reset release, and brownout behavior in the complete power tree rather than assuming a laboratory supply represents the final system.
Do not treat every LPC2119 order code as an unconditional substitute. The suffix can encode ordering, temperature, packaging, or lifecycle conditions that matter to production qualification. Before replacing LPC2119FBD64, compare the manufacturer ordering table, package drawing, pin description, errata, temperature range, and application qualification. Also verify that existing firmware and the boot path operate correctly with the replacement. A matching package and clock rate alone do not establish full application compatibility.
Compliance-Informationen
The available manufacturer and distributor information does not explicitly state the requested compliance status for LPC2119FBD64. AEC-Q100 status is recorded as not applicable because no automotive qualification claim is established for this order code.