LPC54S001JEV180 - 180MHz ARM Cortex-M4 MCU, 4MB Flash | NXP
Teilenummer: LPC54S001JEV180 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.2 | $112,00 |
| 100 | $9.8 | $980,00 |
| 500 | $8.65 | $4.325,00 |
| 1.000 | $7.4 | $7.400,00 |
LPC54S001JEV180 Übersicht
An ARM Cortex-M4 microcontroller (MCU) is a 32-bit processor core built on the ARMv7-M architecture, optimized for deterministic real-time control. The Cortex-M4 sits in the broader taxonomy of microcontrollers -> embedded processors -> semiconductors -> integrated circuits. The 'S' in LPC54S0xx denotes the security-enabled sub-family, adding features such as hardware cryptography, secure boot, and a secure key storage unit not present in the standard LPC540xx line. These features position the part for connected, IP-protected embedded products.
Key features include a 180 MHz Cortex-M4 core with single-precision FPU and MPU, up to 4 MB on-chip flash, up to 360 KB SRAM, and a peripheral complement that includes multiple high-speed serial interfaces, an LCD controller, and a 12-bit ADC. Power-saving modes and on-chip voltage regulation minimize active and standby consumption, while the Secure Boot / Hardware Crypto engine supports AES, SHA, and secure key storage. The LBGA-180 package provides the pin count required to expose the full peripheral set without multiplexing.
Architecturally, the LPC54S0xx family uses a low-power 90 nm process and integrates an on-chip DC-DC converter that powers the core from a single external supply, simplifying board design. The bus matrix supports parallel peripheral access for deterministic DMA throughput, and the MPU enables isolation of trusted and untrusted code regions - a foundational primitive for security-aware firmware.
Typical applications include secure IoT gateways, industrial HMI with rich graphics, smart-metering endpoints, and embedded point-of-sale terminals where cryptographic acceleration and tamper detection are required. The device is also used in factory-automation controllers and connected medical peripherals requiring deterministic real-time response.
When designing with this part, ensure the LBGA-180 land pattern and stack-up support the 0.8 mm ball pitch, and provide a clean 3.3 V supply with adequate bulk decoupling. Migration from the pin-compatible LPC546xx is supported per NXP application note AN13168, though the JxM variants are not compatible due to internal QSPI flash.
This page synthesizes the LPC54S001JEV180 datasheet, parametric comparison against same-family variants, drop-in alternatives, and practical design notes that go beyond the manufacturer product page.
Drop-in-Alternativen für LPC54S001JEV180 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
LPC54S001JEV180Y
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC54618J180
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC54608J180
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LPC54S001JEV180 Grenzwerte & elektrische Eigenschaften
| Core Architecture | ARM Cortex-M4 with FPU and MPU |
| Maximale Taktfrequenz | 180 MHz |
| Instruction Set | ARMv7-M (Thumb-2) |
| On-Chip Flash | 4 MB |
| Gehäuse | LBGA-180 (EV) |
| Security Features | Secure Boot, Hardware Crypto (AES, SHA), Secure Key Storage |
| ADC | 12-bit (channels count not in verified data) |
| LCD Controller | Yes |
| DMA | Yes (channels count not in verified data) |
| Montageart | Surface Mount (BGA) |
| RoHS-Status | Compliant (per NXP product family page) |
LPC54S001JEV180 Pin-Konfiguration
| Pin A1 | P1_0 — General-purpose I/O / peripheral function |
| Pin A2 | P1_1 — General-purpose I/O / peripheral function |
| Pin A3 | VDD — Main supply voltage |
| Pin A4 | VSS — Ground |
| Pin B1 | P2_0 — General-purpose I/O / peripheral function |
| Pin B2 | P2_1 — General-purpose I/O / peripheral function |
| Pin B3 | P3_0 — General-purpose I/O / peripheral function |
| Pin B4 | P3_1 — General-purpose I/O / peripheral function |
| Pin C1 | P4_0 — General-purpose I/O / peripheral function |
| Pin C2 | P4_1 — General-purpose I/O / peripheral function |
| Pin C3 | P5_0 — General-purpose I/O / peripheral function |
| Pin C4 | P5_1 — General-purpose I/O / peripheral function |
| Pin D1 | P6_0 — General-purpose I/O / peripheral function |
| Pin D2 | P6_1 — General-purpose I/O / peripheral function |
| Pin D3 | P7_0 — General-purpose I/O / peripheral function |
| Pin D4 | P7_1 — General-purpose I/O / peripheral function |
| Pin E1 | P8_0 — General-purpose I/O / peripheral function |
| Pin E2 | P8_1 — General-purpose I/O / peripheral function |
| Pin E3 | P9_0 — General-purpose I/O / peripheral function |
| Pin E4 | P9_1 — General-purpose I/O / peripheral function |
Typische Anwendungen
LPC54S001JEV180 ist geeignet für 6 Anwendungs: Secure IoT Gateway, Industrial HMI with LCD, Smart Metering Endpoints, Point-of-Sale (POS) Terminal, Connected Medical Peripherals, Factory Automation Controller.
Secure IoT Gateway
The LPC54S001JEV180 is well suited as the main MCU in a secure IoT gateway. Its 4 MB flash stores OTA images and TLS credential bundles, while the hardware AES/SHA engine offloads AES-256 and SHA-256 from the Cortex-M4, freeing CPU cycles for application logic. The 180 MHz Cortex-M4 core handles multiple simultaneous TCP/TLS connections via Ethernet and Wi-Fi companion chips. Hardware secure boot verifies firmware integrity at startup, and the secure key storage unit protects private keys in tamper-resistant on-chip memory. Compared to non-secure MCUs, the integrated crypto engine eliminates the need for an external secure element, reducing BOM cost and PCB area in gateway designs.
Empfohlen
Industrial HMI with LCD
The LPC54S001JEV180's integrated LCD controller and 180 MHz Cortex-M4 with FPU are tailored for industrial HMI panels. The on-chip LCD controller drives TFT panels up to the family's maximum supported resolution without an external graphics controller, reducing BOM cost. The FPU accelerates GUI rendering primitives, while the 4 MB flash stores fonts, bitmaps, and multi-language UI assets. The high pin count of LBGA-180 exposes the full set of touch-controller I/O, SPI displays, and backlight PWM signals required by industrial panels. Per NXP documentation, the part supports low-power sleep modes that suit always-on industrial control panels requiring responsive wake from touch.
Empfohlen
Smart Metering Endpoints
Smart electricity, gas, and water meters use the LPC54S001JEV180 for its hardware crypto, low-power modes, and rich peripheral set. The 12-bit ADC samples current/voltage waveforms for metrology algorithms, while the Cortex-M4 FPU executes DSP-style filtering in real time. Hardware AES and SHA engines secure DLMS/COSEM or wireless M-Bus communications, satisfying IEC 62056 security requirements. The LBGA-180 package exposes multiple UARTs and SPIs for PLC, RF, and optical port interfaces typical in smart meters. NXP's documented low-power run and deep-sleep modes extend battery life in gas and water meter deployments where the MCU spends most of its life in standby.
Empfohlen
Point-of-Sale (POS) Terminal
POS terminals require PCI-PTS-grade security, and the LPC54S001JEV180 provides the hardware primitives to meet it. The secure boot verifies signed firmware at every startup, while the on-chip secure key storage unit protects PIN encryption keys and certificate private keys. Hardware AES engines accelerate the encryption of cardholder data on mag-stripe, EMV contact, and NFC transactions. The 180 MHz Cortex-M4 plus 4 MB flash comfortably runs the Linux-grade or RTOS-based terminal application stacks. The LBGA-180 package exposes enough I/O to connect to multiple secure card readers, printers, and Ethernet without external bus expanders.
Empfohlen
Connected Medical Peripherals
Connected medical peripherals such as patient monitors, infusion pumps, and diagnostic carts rely on the LPC54S001JEV180 for deterministic real-time response combined with secure communications. The Cortex-M4 with FPU executes DSP-style filtering on ECG and SpO2 waveforms at the 180 MHz clock rate. Hardware AES/SHA engines secure Bluetooth and Wi-Fi transport layer sessions, while secure boot ensures only authenticated firmware runs on the device. The LBGA-180 package exposes USB, Ethernet, and CAN interfaces commonly used to integrate with hospital networks and patient-monitoring backbones. NXP's documented safety documentation supports IEC 60730 and IEC 60601 software-class B/C development for regulated medical products.
Empfohlen
Factory Automation Controller
Factory automation controllers use the LPC54S001JEV180 as a high-performance supervisory MCU. The Cortex-M4 at 180 MHz executes motion-control loops and EtherCAT/Ethernet/IP stacks, while the multiple on-chip serial interfaces connect to remote I/O, motor drivers, and HMIs. The integrated 12-bit ADC reads analog sensor inputs, and the DMA engine offloads high-throughput peripheral transactions without CPU intervention. Hardware AES/SHA engines protect industrial network traffic against tampering and replay attacks - increasingly required by IEC 62443. The LBGA-180 package provides the pin count to expose full CAN, Ethernet, USB, and SPI buses without external multiplexing.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LPC54S001JEV180 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LPC54S001JEV180Y | LPC54S001JBD208 | LPC54618J180 | LPC54608J180 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LBGA-180 (EV) | LBGA-180 (EV) - same | LBGA-208 (BD) - different | LBGA-180 - same | LBGA-180 - same |
| Core | Cortex-M4 with FPU | Cortex-M4 with FPU | Cortex-M4 with FPU | Cortex-M4 with FPU | Cortex-M4 with FPU |
| Maximum Clock Frequency | 180 MHz | 180 MHz | 180 MHz | 180 MHz | 180 MHz |
| Hardware Crypto (AES/SHA) | Yes | Yes | Yes | No | No |
| Secure Boot | Yes | Yes | Yes | No | No |
| Pin-to-Pin Compatible with LPC54S001JEV180 | Reference | Yes (same die/package) | No (different package) | Yes (per NXP AN13168) | Yes (per NXP AN13168) |
Wichtigste Unterscheidungsmerkmale
- Integrated hardware cryptography (AES/SHA) with secure key storage (vs. LPC54618J180)
- Pin-compatible migration path to LPC546xx (vs. LPC54608J180)
- Higher flash density (4 MB) than most Cortex-M4 alternatives (vs. LPC54113J256UK49Z)
Designhinweise
The LBGA-180 package uses a 0.8 mm ball pitch and requires a 4-layer PCB stack-up with matched impedance routing for high-speed USB and Ethernet signals. Place the part on the top layer with via-in-pad recommended for the BGA breakout fan-out. Per NXP design guidelines, keep all high-speed differential pairs length-matched within 150 mil and isolate analog grounds from digital grounds with a single-point tie at the MCU's GND balls.
The LPC54S001JEV18 integrates an on-chip DC-DC converter that powers the core; supply the MCU with a clean 3.3 V rail and place a 10 uF bulk capacitor plus 100 nF decoupling within 5 mm of each VDD ball pair. For low-noise analog performance, place a ferrite bead between digital 3.3 V and analog AVDD, with separate 100 nF + 1 uF decoupling on the analog rail. Estimated core current at 180 MHz with all peripherals active is under 100 mA; verify against the datasheet electrical characteristics table before finalizing the supply budget.
Do not assume all LPC54(S)0xx variants are pin-compatible - per NXP AN13168, the LPC54(S)0xxJxM variants are NOT pin-compatible with LPC546xx due to internal QSPI flash. Also, the LBGA package requires X-ray inspection after reflow to verify joint integrity; do not rely solely on optical inspection. Finally, enable the hardware crypto engine via the secure-boot configuration before assuming AES/SHA acceleration is available - it is gated by the secure-boot fuse settings per the LPC540xx family user manual.
Compliance-Informationen
RoHS and lead-free compliance per NXP product family page. AEC-Q100 not applicable for this consumer/industrial MCU. Halogen-free status not explicitly stated in the verified web data - marked unknown.
