Analog Devices

LT1179ACJ - 4-Channel Micropower Precision Op Amp | Analog Devices

Teilenummer: LT1179ACJ ✓ Aktiv
17 µA Vdss 14-pin CERDIP Package
MOQ: 1 |

LT1179ACJ Übersicht

Analog Devices LT1179ACJ is a micropower, four-channel precision operational amplifier optimized for single-supply operation at 5 V, with additional specifications defined at ±15 V supplies. The device uses a maximum supply current of 17 µA and provides four amplifiers in a 14-pin ceramic dual in-line package. According to the manufacturer product page, its low supply current is combined with precision specifications including 30 µV offset voltage and low offset current.

An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals. The LT1179 belongs to the precision operational amplifier category and then to the broader amplifier IC and semiconductor hierarchies. Its four independent channels make it useful wherever several low-level signals must be conditioned while keeping power consumption and board area low.

The LT1179ACJ is designed around the micropower precision amplifier concept. Each channel provides high open-loop gain, low input offset voltage, and low input bias behavior while operating from a single 5 V supply. The 17 µA maximum supply-current figure makes the device relevant to battery-powered instrumentation, portable measurement systems, and industrial controls where amplifier power can dominate the standby budget. Operation at ±15 V also supports higher-level bipolar signal chains.

The four-channel architecture reduces the number of packages required when a design needs multiple amplification paths. A single LT1179ACJ can implement four amplifiers instead of using four separate single or dual amplifier packages. This simplifies inventory, reduces board-level component count, and can lower assembly cost. The tradeoff is that all four channels share one package and one supply, so a fault or power-distribution problem can affect more than one signal path.

Typical uses include low-level sensor amplification, current-to-voltage conversion, instrumentation buffering, precision bridge excitation, active filtering, and general-purpose analog signal conditioning. The device can be especially useful in portable instruments where four precision channels are needed but each channel's operating current must remain low. Supply bypassing and input-common-mode limits should still be checked against the manufacturer's operating conditions.

For PCB design, place the bypass capacitor close to the positive and negative supply pins and maintain short, low-noise paths from sensitive inputs. Ceramic input filtering should account for input-bias-current effects rather than treating every capacitor value as ideal. Ceramic-DIP construction also requires adequate mechanical clearance and proper socket or soldering practices.

This page combines the manufacturer's LT1179 family information with distributor package details and practical guidance for precision, low-power analog design. It also distinguishes the directly comparable family variants while making clear where a new schematic review is required before selecting a replacement.

Drop-in-Alternativen für LT1179ACJ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

LT1179AHJS

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin CERDIP
Four channels and 14-pin ceramic-DIP pinout are unchanged (0% topology difference); LT1179AHJS provides wider temperature-grade capability than the 0 °C to 70 °C LT1179ACJ.

📋 Referenzalternative (nicht im Katalog)

LT1179CZ

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin CERDIP
Four channels and 14-pin ceramic-DIP pinout are unchanged (0% topology difference); LT1179CZ is intended for a wider environmental temperature grade than the commercial LT1179ACJ.

📋 Referenzalternative (nicht im Katalog)

LT1179ACJ Grenzwerte & elektrische Eigenschaften

Number of Amplifiers 4 circuits
Product Type Micropower precision operational amplifier
Maximum Supply Current 17 µA
Optimized Supply Voltage 5 V
Additional Supply Condition ±15 V
Input Offset Voltage 30 µV
Betriebstemperaturbereich 0 °C to 70 °C
Gehäuse 14-pin CERDIP
Montageart Through-hole

LT1179ACJ Pin-Konfiguration

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
Pin 1 OUT1 — Amplifier 1 output
Pin 2 IN1- — Amplifier 1 inverting input
Pin 3 IN1+ — Amplifier 1 non-inverting input
Pin 4 V- — Negative supply
Pin 5 IN2+ — Amplifier 2 non-inverting input
Pin 6 IN2- — Amplifier 2 inverting input
Pin 7 OUT2 — Amplifier 2 output
Pin 8 OUT3 — Amplifier 3 output
Pin 9 IN3- — Amplifier 3 inverting input
Pin 10 IN3+ — Amplifier 3 non-inverting input
Pin 11 V+ — Positive supply
Pin 12 IN4+ — Amplifier 4 non-inverting input
Pin 13 IN4- — Amplifier 4 inverting input
Pin 14 OUT4 — Amplifier 4 output

Typische Anwendungen

LT1179ACJ ist geeignet für 6 Anwendungs: Battery-Powered Sensor Conditioning, Precision Bridge Amplifier Interface, Portable Test and Measurement, Low-Power Active Filtering, Current-to-Voltage Conversion, Precision Voltage Reference Buffering.

🔋

Battery-Powered Sensor Conditioning

The LT1179ACJ fits battery-powered sensor front ends because it combines four precision amplifier channels with a maximum supply current of 17 µA. It can condition four low-level inputs from resistive sensors while operating from a single 5 V rail, reducing the number of packages needed for a multichannel measurement circuit. The low channel count available in one device does not increase the device-level supply current quoted by the manufacturer, although actual consumption varies with output voltage, load, and operating mode. Decouple the 5 V supply locally and keep sensor traces away from switching nodes so that low supply demand translates into useful measurement performance rather than additional noise.

🏭

Precision Bridge Amplifier Interface

The LT1179ACJ is suitable for multiple instrumentation channels because each amplifier can support a bridge or differential sensor interface around a single 5 V supply. Four channels allow an instrument to process several strain-gauge, pressure, or resistive bridges without using four separate amplifier packages. Its 30 µV offset-voltage specification supports precision signal conditioning, while the 17 µA maximum supply current helps preserve battery life. The application remains sensitive to bridge excitation accuracy, input bias current, resistor matching, and common-mode range, so calculate those values against the exact operating points in the manufacturer datasheet before finalizing the board.

🖥️

Portable Test and Measurement

A portable meter or calibrator can use the LT1179ACJ to amplify four low-level channels in a compact through-hole analog section. Its 17 µA maximum supply current is valuable when the instrument spends substantial time on battery power, while the four-channel configuration reduces package count and simplifies the power distribution. The amplifiers can support buffer, gain, active-filter, or current-to-voltage functions, subject to bandwidth and output-swing limits. Keep sensitive inputs short, use a low-noise reference and properly bypassed 5 V rail, and validate the complete acquisition path rather than attributing system accuracy to offset voltage alone.

🔧

Low-Power Active Filtering

The LT1179ACJ can implement multiple active filters or cascaded gain stages when low power is more important than maximum bandwidth. Its four channels allow a compact analog frontend to combine anti-alias filtering, gain, and buffering around a single 5 V supply. The 17 µA maximum supply-current specification reduces the amplifier's contribution to total instrument power, but each closed-loop stage still consumes additional current as its operating point changes. Confirm the required gain-bandwidth product, slew rate, output load, and stability margin in the datasheet, and keep the feedback components close to the corresponding amplifier pins to reduce parasitic effects.

⚡

Current-to-Voltage Conversion

The LT1179ACJ is useful for monitoring four low-current sources with a transimpedance amplifier configuration. The LT1179's low maximum supply current of 17 µA helps limit the amplifier's contribution to an energy-harvesting or battery-powered monitor, and the 30 µV offset specification supports measurements where small converted voltages must retain useful accuracy. A practical design must account for feedback-resistor noise, input bias current across the feedback impedance, input capacitance, and the common-mode voltage produced at the virtual ground. Use guarded, short input routing and verify stable compensation against the actual sensor and cable capacitance.

📡

Precision Voltage Reference Buffering

The LT1179ACJ can buffer a low-current voltage reference or supply auxiliary analog signals while drawing very little supply current. Four channels make it practical to buffer one reference for multiple analog sections, or to use the remaining amplifiers for gain and filtering stages. The specified 30 µV offset voltage supports accurate reference buffering, and the single 5 V operating focus simplifies portable-system design. Reference accuracy still depends on loading, reference output impedance, temperature drift, and the amplifier's input bias current, so verify those characteristics directly. Place the reference output and feedback node on quiet board areas and avoid routing high-current return paths beneath them.

Zusammenfassung der empfohlenen Produkte

LT1179AHJS Same-family wider-temperature alternative Verwendet in: Battery-Powered Sensor Conditioning, Precision Bridge Amplifier Interface, Portable Test and Measurement, Low-Power Active Filtering, Current-to-Voltage Conversion, Precision Voltage Reference Buffering LT1179CZ Same-family ceramic-DIP alternative Verwendet in: Battery-Powered Sensor Conditioning, Precision Bridge Amplifier Interface, Portable Test and Measurement, Low-Power Active Filtering, Current-to-Voltage Conversion, Precision Voltage Reference Buffering
What is the LT1179ACJ?
The LT1179ACJ is a four-channel micropower precision operational amplifier from Analog Devices, specified for operation from a single 5 V supply with a maximum supply current of 17 µA. According to the manufacturer product page, the device combines low power with 30 µV offset-voltage specifications and is packaged in a 14-pin CERDIP. The four channels share one package and supply, making the device useful for compact, low-power analog signal-conditioning designs.
How many amplifiers are in the LT1179ACJ?
The LT1179ACJ contains four independent operational amplifiers. The manufacturer describes the LT1179 as a micropower quad op amp and specifies a maximum supply current of 17 µA for the device. Using four channels in one 14-pin CERDIP can reduce package count and board area compared with four separate amplifier packages, although a shared power-distribution fault would affect all four channels.
What supply voltage does the LT1179ACJ use?
The LT1179ACJ is optimized for a single 5 V supply, and the manufacturer also provides specifications for operation at ±15 V. The 5 V configuration is important for battery-powered or compact instrumentation because the amplifier can process signals referenced to a single rail without requiring a split supply. The exact input and output limits for each operating condition are listed in the manufacturer datasheet.
Where can I download the LT1179ACJ datasheet PDF?
The official LT1179 family information and datasheet are available through Analog Devices at https://www.analog.com/en/products/lt1179.html. The family document defines the LT1179 as a micropower quad precision amplifier optimized for 5 V single-supply operation and includes specifications at ±15 V. Use the manufacturer's document for final pin functions, electrical limits, test conditions, and ordering information.
Where can I find the LT1179ACJ pinout?
The LT1179ACJ uses a conventional 14-pin operational-amplifier arrangement: four outputs, eight input terminals, one positive-supply pin, and one negative-supply pin. The manufacturer datasheet contains the definitive pin-number table and package drawing. When using a socket, confirm orientation against the notch and pin-1 marking before inserting or soldering the device.
What are the key specifications of LT1179ACJ that engineers should know?
The LT1179ACJ combines four precision amplifier channels, a 17 µA maximum supply current, 30 µV input offset voltage, single-supply operation at 5 V, and a 14-pin CERDIP package. According to the Analog Devices product page, specifications are also provided at ±15 V. Its primary engineering value is the combination of four channels and very low supply current in one through-hole package.
Is the LT1179ACJ suitable for battery-powered instrumentation?
Yes, the LT1179ACJ is suitable for many battery-powered instrumentation designs because its maximum supply current is specified at 17 µA and it operates from a single 5 V supply. Four channels can condition sensor, reference, or feedback signals without requiring four separate amplifier packages. The complete system budget should also include sensor current, ADC current, leakage, and power-conversion losses.
What can replace the LT1179ACJ?
The closest replacement must use the same 14-pin ceramic-DIP footprint and preserve the quad-amplifier pin arrangement. Same-family LT1179 temperature-grade and package variants may serve as drop-in candidates when their electrical ratings and qualification requirements match the design. Confirm pin functions, supply range, common-mode range, offset voltage, bandwidth, and operating temperature before accepting any replacement.
What is the best Analog Devices equivalent for LT1179ACJ?
The best Analog Devices equivalent is the same-family LT1179 variant with a 14-pin ceramic-DIP package and an identical pinout, selected according to temperature grade and qualification needs. The LT1179AHJS and LT1179CZ are relevant family candidates, but neither should be substituted solely by name. Review the manufacturer ordering table and datasheet to confirm electrical limits and environmental requirements.
LT1179ACJ vs LT1179AHJS: which is better for a design?
The LT1179ACJ is the commercial-temperature 0 °C to 70 °C choice, while the LT1179AHJS is a military-oriented same-family variant with a wider environmental qualification. Choose LT1179ACJ when the 14-pin CERDIP construction and commercial-temperature range satisfy the product requirements. Choose LT1179AHJS when wider temperature coverage or the relevant defense qualification is required.
When should I choose LT1179ACJ over a quad op amp in a surface-mount package?
Choose LT1179ACJ when a through-hole ceramic DIP is acceptable and low power, four-channel precision operation, or legacy board compatibility is more important than PCB area. A surface-mount quad amplifier may be preferable for compact new equipment, automated assembly, or tighter board-space limits. Both implementation paths must satisfy the same input, output, bandwidth, noise, and thermal requirements.
Can LT1179AHJS replace LT1179ACJ in an existing PCB?
The LT1179AHJS can be considered a same-family, same-package replacement when its pinout, electrical ratings, and temperature qualification meet the circuit requirements. Both devices use the 14-pin CERDIP arrangement and four-channel topology. Review the manufacturer datasheet for operating-range, supply-current, offset-voltage, and qualification differences before production substitution.
Where can I buy LT1179ACJ and check its current price?
Use the Request a Quote form on this page to request LT1179ACJ availability, current pricing, quantity breaks, and lead time. The commercial quote workflow is the appropriate way to confirm the exact ceramic-DIP ordering code and any lot or traceability requirements. Do not substitute an 8-pin, 16-pin, or surface-mount variant without checking the footprint.
What is the lead time for LT1179ACJ?
The current lead time and minimum order quantity should be requested through the Request a Quote form on this page. Lead time can vary with manufacturer inventory, package construction, order quantity, and traceability requirements. Provide the target quantity and required temperature grade so the quotation corresponds to the exact LT1179ACJ ordering code.
Is LT1179ACJ in stock?
Current stock for LT1179ACJ should be confirmed through the Request a Quote form on this page. Because availability can change with production schedules, distributor inventory, and order quantity, the form is the reliable source for a current allocation. Specify the required package and quantity when requesting the quotation.
Does the LT1179ACJ need a heatsink?
The LT1179ACJ normally does not require a dedicated heatsink because its maximum supply current is only 17 µA and it uses a through-hole 14-pin CERDIP package. Power dissipation is low compared with a high-current output amplifier, although actual dissipation depends on supply voltage, output swing, load, and ambient temperature. Maintain normal PCB airflow and avoid enclosing the device without thermal analysis.

Technische Referenzdaten für LT1179ACJ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the LT1179ACJ when a design requires four precision amplifier channels, very low supply current, single 5 V operation, and a 14-pin ceramic through-hole package. It is particularly appropriate for portable instrumentation, low-level sensor conditioning, bridge interfaces, and legacy through-hole designs operating from 0 °C to 70 °C. Select the LT1179AHJS when the same family topology and package are required but wider temperature or defense-oriented qualification is needed. Select the LT1179CZ for similar wider-environment applications after confirming its exact ratings. Do not choose any of these parts solely from the 14-pin outline: verify supply limits, common-mode range, output swing, bandwidth, offset voltage, and lead dimensions. For a new compact surface-mount product, a modern surface-mount quad amplifier may be mechanically preferable even if it is not a direct drop-in replacement.

Vergleich mit Alternativen

Parameter Dieses Produkt LT1179AHJS LT1179CZ
Brand Analog Devices Analog Devices Analog Devices
Package 14-pin CERDIP 14-pin CERDIP 14-pin CERDIP
Number of Amplifiers 4 circuits 4 circuits 4 circuits
Optimized Supply Voltage 5 V 5 V 5 V
Additional Supply Condition ±15 V ±15 V ±15 V
Mounting Type Through-hole Through-hole Through-hole
Special Qualification Commercial temperature grade Wider-temperature military-oriented grade Wider-temperature military-oriented grade

Wichtigste Unterscheidungsmerkmale

  • Four precision channels in one low-power package (vs. LT1179AHJS)
  • Commercial-temperature alternative with the same quad topology (vs. LT1179CZ)
  • Single-package channel consolidation (vs. LT1179AHJS)

Designhinweise

Connect a low-inductance bypass capacitor close to the V+ and V- pins and provide adequate return-current paths for all four channels. The family is optimized for a single 5 V supply and also has specifications at ±15 V, but the usable input and output ranges depend on the selected supply configuration. Keep analog return current separate from switching-node current where possible so that the 17 µA maximum supply-current specification is not undermined by supply ripple coupled into sensitive inputs.

Keep each inverting input and its feedback components on the same side of the board as the associated amplifier channel. Route the non-inverting inputs away from clocks, relays, power inductors, and other high-impedance nodes. Because this is a precision quad amplifier, identical channel layouts and short feedback paths help reduce channel-to-channel error and susceptibility to contamination on the input nodes.

Do not select the LT1179ACJ solely by its 14-pin DIP outline and then change to a surface-mount quad amplifier without redesigning the PCB. Confirm the ceramic-DIP pin mapping, supply voltage, input common-mode range, output swing, offset-voltage grade, bandwidth, and operating temperature. Also verify that the replacement's package lead dimensions and socket compatibility match the mechanical drawing, not only the nominal pin count.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available manufacturer and distributor pages do not state the requested environmental or material-compliance details. AEC-Q100 is treated as not applicable because this product is an industrial and commercial general-purpose amplifier rather than an automotive-qualified device.

Ähnliche Suchanfragen

LT1179ACJ datasheet LT1179ACJ pinout LT1179ACJ datasheet pdf LT1179ACJ equivalent LT1179ACJ replacement LT1179ACJ cross reference LT1179ACJ vs LT1179AHJS LT1179ACJ price LT1179ACJ stock Analog Devices LT1179ACJ LT1179 14-pin CERDIP LT1179ACJ application circuit

Verwandte Bauteile & Begriffe

Analog Devices LT1179ACJ LT1179 LT1179AHJS LT1179CZ operational amplifier precision operational amplifier micropower amplifier quad amplifier amplifier IC analog signal conditioning single-supply operation 5 V power supply input offset voltage input bias current open-loop gain unity-gain bandwidth slew rate 14-pin CERDIP through-hole package battery-powered instrumentation bridge amplifier current-to-voltage conversion active filter precision voltage reference
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen