LT1179ACJ - 4-Channel Micropower Precision Op Amp | Analog Devices
MPN: LT1179ACJ ✓ AktifLT1179ACJ Ringkasan
An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals. The LT1179 belongs to the precision operational amplifier category and then to the broader amplifier IC and semiconductor hierarchies. Its four independent channels make it useful wherever several low-level signals must be conditioned while keeping power consumption and board area low.
The LT1179ACJ is designed around the micropower precision amplifier concept. Each channel provides high open-loop gain, low input offset voltage, and low input bias behavior while operating from a single 5 V supply. The 17 µA maximum supply-current figure makes the device relevant to battery-powered instrumentation, portable measurement systems, and industrial controls where amplifier power can dominate the standby budget. Operation at ±15 V also supports higher-level bipolar signal chains.
The four-channel architecture reduces the number of packages required when a design needs multiple amplification paths. A single LT1179ACJ can implement four amplifiers instead of using four separate single or dual amplifier packages. This simplifies inventory, reduces board-level component count, and can lower assembly cost. The tradeoff is that all four channels share one package and one supply, so a fault or power-distribution problem can affect more than one signal path.
Typical uses include low-level sensor amplification, current-to-voltage conversion, instrumentation buffering, precision bridge excitation, active filtering, and general-purpose analog signal conditioning. The device can be especially useful in portable instruments where four precision channels are needed but each channel's operating current must remain low. Supply bypassing and input-common-mode limits should still be checked against the manufacturer's operating conditions.
For PCB design, place the bypass capacitor close to the positive and negative supply pins and maintain short, low-noise paths from sensitive inputs. Ceramic input filtering should account for input-bias-current effects rather than treating every capacitor value as ideal. Ceramic-DIP construction also requires adequate mechanical clearance and proper socket or soldering practices.
This page combines the manufacturer's LT1179 family information with distributor package details and practical guidance for precision, low-power analog design. It also distinguishes the directly comparable family variants while making clear where a new schematic review is required before selecting a replacement.
Pilihan pengganti yang segera untuk LT1179ACJ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
LT1179AHJS
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
LT1179CZ
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
LT1179ACJ Penilaian maksimum & Ciri-ciri Elektrik
| Number of Amplifiers | 4 circuits |
| Product Type | Micropower precision operational amplifier |
| Maximum Supply Current | 17 µA |
| Optimized Supply Voltage | 5 V |
| Additional Supply Condition | ±15 V |
| Input Offset Voltage | 30 µV |
| Gambaran Suhu Operasi | 0 °C to 70 °C |
| Kemasan | 14-pin CERDIP |
| Jenis Pemasangan | Through-hole |
Konfigurasi Pin LT1179ACJ
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply |
| Pin 5 | IN2+ — Amplifier 2 non-inverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | IN3- — Amplifier 3 inverting input |
| Pin 10 | IN3+ — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply |
| Pin 12 | IN4+ — Amplifier 4 non-inverting input |
| Pin 13 | IN4- — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Aplikasi Biasa
LT1179ACJ patut untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Precision Bridge Amplifier Interface, Portable Test and Measurement, Low-Power Active Filtering, Current-to-Voltage Conversion, Precision Voltage Reference Buffering.
Battery-Powered Sensor Conditioning
The LT1179ACJ fits battery-powered sensor front ends because it combines four precision amplifier channels with a maximum supply current of 17 µA. It can condition four low-level inputs from resistive sensors while operating from a single 5 V rail, reducing the number of packages needed for a multichannel measurement circuit. The low channel count available in one device does not increase the device-level supply current quoted by the manufacturer, although actual consumption varies with output voltage, load, and operating mode. Decouple the 5 V supply locally and keep sensor traces away from switching nodes so that low supply demand translates into useful measurement performance rather than additional noise.
Disebarkan
Precision Bridge Amplifier Interface
The LT1179ACJ is suitable for multiple instrumentation channels because each amplifier can support a bridge or differential sensor interface around a single 5 V supply. Four channels allow an instrument to process several strain-gauge, pressure, or resistive bridges without using four separate amplifier packages. Its 30 µV offset-voltage specification supports precision signal conditioning, while the 17 µA maximum supply current helps preserve battery life. The application remains sensitive to bridge excitation accuracy, input bias current, resistor matching, and common-mode range, so calculate those values against the exact operating points in the manufacturer datasheet before finalizing the board.
Disebarkan
Portable Test and Measurement
A portable meter or calibrator can use the LT1179ACJ to amplify four low-level channels in a compact through-hole analog section. Its 17 µA maximum supply current is valuable when the instrument spends substantial time on battery power, while the four-channel configuration reduces package count and simplifies the power distribution. The amplifiers can support buffer, gain, active-filter, or current-to-voltage functions, subject to bandwidth and output-swing limits. Keep sensitive inputs short, use a low-noise reference and properly bypassed 5 V rail, and validate the complete acquisition path rather than attributing system accuracy to offset voltage alone.
Disebarkan
Low-Power Active Filtering
The LT1179ACJ can implement multiple active filters or cascaded gain stages when low power is more important than maximum bandwidth. Its four channels allow a compact analog frontend to combine anti-alias filtering, gain, and buffering around a single 5 V supply. The 17 µA maximum supply-current specification reduces the amplifier's contribution to total instrument power, but each closed-loop stage still consumes additional current as its operating point changes. Confirm the required gain-bandwidth product, slew rate, output load, and stability margin in the datasheet, and keep the feedback components close to the corresponding amplifier pins to reduce parasitic effects.
Disebarkan
Current-to-Voltage Conversion
The LT1179ACJ is useful for monitoring four low-current sources with a transimpedance amplifier configuration. The LT1179's low maximum supply current of 17 µA helps limit the amplifier's contribution to an energy-harvesting or battery-powered monitor, and the 30 µV offset specification supports measurements where small converted voltages must retain useful accuracy. A practical design must account for feedback-resistor noise, input bias current across the feedback impedance, input capacitance, and the common-mode voltage produced at the virtual ground. Use guarded, short input routing and verify stable compensation against the actual sensor and cable capacitance.
Disebarkan
Precision Voltage Reference Buffering
The LT1179ACJ can buffer a low-current voltage reference or supply auxiliary analog signals while drawing very little supply current. Four channels make it practical to buffer one reference for multiple analog sections, or to use the remaining amplifiers for gain and filtering stages. The specified 30 µV offset voltage supports accurate reference buffering, and the single 5 V operating focus simplifies portable-system design. Reference accuracy still depends on loading, reference output impedance, temperature drift, and the amplifier's input bias current, so verify those characteristics directly. Place the reference output and feedback node on quiet board areas and avoid routing high-current return paths beneath them.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LT1179ACJ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LT1179AHJS | LT1179CZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 14-pin CERDIP | 14-pin CERDIP | 14-pin CERDIP |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits |
| Optimized Supply Voltage | 5 V | 5 V | 5 V |
| Additional Supply Condition | ±15 V | ±15 V | ±15 V |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Special Qualification | Commercial temperature grade | Wider-temperature military-oriented grade | Wider-temperature military-oriented grade |
Penyeberangsung Jelas
- Four precision channels in one low-power package (vsLT1179AHJS)
- Commercial-temperature alternative with the same quad topology (vsLT1179CZ)
- Single-package channel consolidation (vsLT1179AHJS)
Catatan Desain
Connect a low-inductance bypass capacitor close to the V+ and V- pins and provide adequate return-current paths for all four channels. The family is optimized for a single 5 V supply and also has specifications at ±15 V, but the usable input and output ranges depend on the selected supply configuration. Keep analog return current separate from switching-node current where possible so that the 17 µA maximum supply-current specification is not undermined by supply ripple coupled into sensitive inputs.
Keep each inverting input and its feedback components on the same side of the board as the associated amplifier channel. Route the non-inverting inputs away from clocks, relays, power inductors, and other high-impedance nodes. Because this is a precision quad amplifier, identical channel layouts and short feedback paths help reduce channel-to-channel error and susceptibility to contamination on the input nodes.
Do not select the LT1179ACJ solely by its 14-pin DIP outline and then change to a surface-mount quad amplifier without redesigning the PCB. Confirm the ceramic-DIP pin mapping, supply voltage, input common-mode range, output swing, offset-voltage grade, bandwidth, and operating temperature. Also verify that the replacement's package lead dimensions and socket compatibility match the mechanical drawing, not only the nominal pin count.
Maklumat Kesediaan
The available manufacturer and distributor pages do not state the requested environmental or material-compliance details. AEC-Q100 is treated as not applicable because this product is an industrial and commercial general-purpose amplifier rather than an automotive-qualified device.