Analog Devices

LTC1338CG - 5V Low-Power RS-232 Transceiver | Analog Devices

Teilenummer: LTC1338CG ✓ Aktiv
5 V Vdss 500 uA Id 28-pin SSOP Package
MOQ: 1 |

LTC1338CG Übersicht

Analog Devices LTC1338CG is a 5V low-power RS-232 transceiver with five drivers, three receivers, a 500 uA no-load supply current, and a 28-pin SSOP package. It operates from a single 5V supply, supports data rates up to 120 kbaud, and includes ESD protection rated to ±10 kV. Four 0.1 uF capacitors are sufficient for the charge-pump circuit, while shutdown mode reduces supply current to 0.2 uA.

An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 equipment. The LTC1338 belongs to the transceiver hierarchy, where a complete interface IC combines line drivers, receivers, charge-pump voltage conversion, and sometimes shutdown control. It is designed for compact serial-port equipment where low supply current, limited board area, and robust electrostatic protection are important.

Five driver outputs support multiple RS-232 channels or control signals, while three receiver inputs support three incoming data or handshake signals. Three-state driver outputs allow the drivers to be disconnected when the bus direction changes. The 120 kbaud capability accommodates legacy communications, industrial controllers, service interfaces, and equipment-control links without requiring a separate external charge-pump supply.

The single 5V architecture simplifies power-system design because the device generates the RS-232 bipolar levels internally. Its low 500 uA no-load supply current reduces standby demand, and the 0.2 uA shutdown current is valuable in portable or intermittently powered instruments. Driver outputs and receiver inputs withstand forced voltages down to −25V without damage, adding protection margin on externally accessible connectors.

Typical uses include legacy serial-port adapters, programmable test equipment, industrial control panels, embedded service interfaces, and communication links between older RS-232 peripherals and modern controller boards. The 28-pin SSOP package supports surface-mount assembly but requires careful handling because the lead pitch is narrower than that of a standard SOIC.

Designers should connect the four 0.1 uF charge-pump capacitors exactly as shown in the manufacturer application information, place them close to the associated pins, and provide adequate bypass capacitance at the supply pins. External protection should supplement the internal ±10 kV ESD rating when cables extend beyond the enclosure or connect to industrial environments.

This page consolidates the device’s principal electrical characteristics, package information, application fit, and verified substitution status. The comparison and design notes emphasize the practical trade-offs that matter when replacing an RS-232 interface without changing the PCB footprint.

Drop-in-Alternativen für LTC1338CG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

LTC1338IG#PBF

✅ Drop-In
📦 28-pin SSOP
Same 28-pin SSOP RS-232 transceiver family and pin architecture; LTC1338IG#PBF is industrial temperature grade versus commercial-grade LTC1338CG.

📋 Referenzalternative (nicht im Katalog)

LTC1338CG Technische Daten

Product Type RS-232 transceiver
Number of Drivers 5
Number of Receivers 3
Versorgungsspannung 5 V
No-Load Supply Current 500 uA
Shutdown Supply Current 0.2 uA
Receiver-Alive Supply Current 50 uA
Maximum Data Rate 120 kbaud
Charge-Pump Capacitors 4 x 0.1 uF
ESD Protection ±10 kV
Driver Output Overvoltage Tolerance −25 V
Receiver Input Overvoltage Tolerance −25 V
Driver Output States 3-state
Gehäuse 28-pin SSOP
Temperature Grade Commercial
Montageart Surface Mount

LTC1338CG 28-pin ssop Pinbelegungsleitfaden

Pinbelegung für LTC1338CG (28-pin ssop-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für LTC1338CG im 28-pin ssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LTC1338CG.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LTC1338CG ist geeignet für 6 Anwendungs: Legacy Serial-Port Adapters, Industrial Control Panels, Programmable Test Equipment, Portable Service Interfaces, Embedded Equipment Control, Communication Port Concentrators.

🔧

Legacy Serial-Port Adapters

The LTC1338CG fits legacy serial-port adapters because it combines five RS-232 drivers and three receivers with operation from a single 5V supply. Up to 120 kbaud support covers many legacy peripherals while the 500 uA no-load current limits standby demand. Four 0.1 uF charge-pump capacitors keep the auxiliary circuit compact, and the 28-pin SSOP package suits adapter boards where connector clearance is limited. The three-state outputs also help a controller-managed interface avoid bus contention during direction changes.

🏭

Industrial Control Panels

The LTC1338CG is useful in industrial control panels that retain RS-232 links to older drives, printers, or service equipment. Its five-driver and three-receiver arrangement supports both data and handshake signals, while 120 kbaud operation provides compatibility with conventional control protocols. Internal ±10 kV ESD protection improves robustness at accessible connectors, although panel-level surge protection may still be required. The low-power architecture also suits controllers that remain powered while the external equipment is idle.

⚡

Programmable Test Equipment

The LTC1338CG can support programmable test equipment that communicates with legacy instruments through RS-232. The five-driver and three-receiver configuration accommodates several control and measurement signals without requiring multiple single-channel transceivers. A maximum rate of 120 kbaud supports older automated-test protocols, while shutdown current of 0.2 uA helps conserve energy between test cycles. The SSOP package reduces board area, although careful assembly practices are necessary because of its narrow lead spacing.

📱

Portable Service Interfaces

The LTC1338CG is appropriate for portable service interfaces because its 500 uA no-load current and 0.2 uA shutdown current reduce demand when the equipment is idle. A single 5V rail simplifies power design, while the integrated charge pump avoids a separate negative supply. The five available drivers can carry multiple control signals, and the three receivers can monitor responses from a peripheral. At the connector, the internal ±10 kV ESD rating provides a useful baseline, with additional external protection advisable for field cables.

🖥️

Embedded Equipment Control

The LTC1338CG suits embedded controllers that must communicate with external RS-232 actuators or instruments. Three receivers allow the controller to monitor device status, acknowledgments, and interlock signals, while five drivers support command and handshake outputs. Its 120 kbaud limit accommodates many embedded control protocols, and the three-state outputs provide a controlled way to disable drivers when the interface direction changes. Single-supply operation also reduces rail complexity in compact control assemblies.

🌐

Communication Port Concentrators

The LTC1338CG can participate in communication port concentrators that adapt legacy equipment to a modern controller. The five drivers and three receivers allow several RS-232 lines to share one interface IC, reducing component count compared with separate single-channel devices. Operation to 120 kbaud and compliance with RS-232 data-rate requirements preserve legacy connectivity. The 28-pin SSOP footprint supports compact concentrator boards, while shutdown control can reduce consumption when a managed port is not active.

What is the LTC1338CG?
The LTC1338CG is a 5V low-power RS-232 interface IC containing five drivers and three receivers in a 28-pin SSOP package. According to the Analog Devices manufacturer datasheet, it supports operation to 120 kbaud, uses four 0.1 uF charge-pump capacitors, and provides internal ESD protection up to ±10 kV. It is intended for compact serial-interface equipment where a single supply rail, low standby current, and a small surface-mount footprint are required.
What are the key specifications of LTC1338CG that engineers should know?
The LTC1338CG combines five RS-232 drivers, three receivers, a single 5V supply, and a maximum data rate of 120 kbaud. Its no-load supply current is 500 uA, while shutdown lowers consumption to 0.2 uA. The Analog Devices manufacturer datasheet also specifies four 0.1 uF charge-pump capacitors, three-state driver outputs, ±10 kV ESD protection, and −25V overvoltage tolerance on driver outputs and receiver inputs.
What is the operating voltage of LTC1338CG?
The LTC1338CG operates from a single 5V supply. The Analog Devices manufacturer datasheet identifies the device as a 5V low-power RS-232 transceiver and states that the on-chip charge pump generates the bipolar signal levels required by RS-232. This simplifies the power architecture compared with older designs requiring separate positive and negative supplies, although normal bypass and charge-pump capacitors must still be placed close to the device.
How fast can LTC1338CG transmit RS-232 data?
The LTC1338CG operates at data rates up to 120 kbaud. The Analog Devices manufacturer datasheet states that the transceiver is fully compliant with RS-232 data-rate and overvoltage specifications and can operate at 120 kbaud with a 2500 pF, 3 kW load. This provides ample margin for legacy peripherals, service consoles, and industrial control links while retaining compatibility with lower baud rates.
Why does LTC1338CG need four 0.1 uF capacitors?
The four 0.1 uF capacitors provide the charge-pump circuit with the stable capacitance required to generate the positive and negative RS-232 voltage levels from a 5V supply. The Analog Devices manufacturer datasheet specifically states that small 0.1 uF capacitors are sufficient. Place each capacitor close to its designated pins and follow the manufacturer connection diagram to minimize loop area and maintain the intended operating behavior.
Where can I download the LTC1338CG datasheet PDF?
The official LTC1338CG datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/lt1338.pdf. The document is the primary reference for electrical characteristics, pin assignments, charge-pump connections, driver and receiver behavior, and operating limits. Use the manufacturer’s pin-description table when assigning PCB nets and when checking the three-state driver-control arrangement.
Where can I find the LTC1338CG pinout?
The LTC1338CG pinout is defined in the Analog Devices manufacturer datasheet at https://www.analog.com/media/en/technical-documentation/data-sheets/lt1338.pdf. The device uses a 28-pin SSOP package, and the datasheet pin table should be used to identify supply, ground, driver, receiver, shutdown, and charge-pump connections. Assign the PCB footprint and verify every net against that table before fabrication.
What can replace LTC1338CG?
The LTC1338IG#PBF is the confirmed same-package alternative identified for the LTC1338CG family, using a 28-pin SSOP footprint and the same five-driver, three-receiver RS-232 function. According to the manufacturer family information, its primary distinction is the industrial temperature grade rather than a change in interface architecture. A broader cross-brand replacement was not established with sufficient pin-level evidence, so review the complete pin and electrical tables before substitution.
Is LTC1338IG#PBF a drop-in replacement for LTC1338CG?
The LTC1338IG#PBF is a drop-in option for the LTC1338CG because it is identified in the same 28-pin SSOP RS-232 transceiver family. The relevant difference is temperature grade: LTC1338CG is commercial, while LTC1338IG#PBF is the industrial-grade ordering option. Confirm the exact ordering suffix, pin mapping, and supply requirements against the Analog Devices manufacturer datasheet before replacing an assembled board.
What is the best equivalent for LTC1338CG?
The best confirmed equivalent is the LTC1338IG#PBF because it retains the LTC1338 interface arrangement in the same 28-pin SSOP package and differs principally in temperature grade. No cross-brand equivalent was verified strongly enough to guarantee drop-in compatibility. For an exact commercial-temperature replacement, use LTC1338CG itself; for industrial operation, evaluate LTC1338IG#PBF against the complete manufacturer electrical and pin tables.
When should I choose LTC1338CG over LTC1338IG#PBF?
Choose LTC1338CG when the equipment operates within the commercial temperature range and the assembly requires the original commercial-grade RS-232 transceiver. Choose LTC1338IG#PBF when environmental temperature demands industrial-grade qualification and the same 28-pin SSOP footprint is needed. Both devices serve the same five-driver, three-receiver interface role, so temperature grade and exact ordering suffix should drive the final selection.
Is LTC1338CG suitable for low-power serial equipment?
The LTC1338CG is suitable for low-power serial equipment because its no-load supply current is 500 uA and shutdown current is only 0.2 uA. According to the Analog Devices manufacturer datasheet, receiver-alive mode draws 50 uA, helping reduce consumption when only receive functions are required. These figures support portable instruments and intermittently powered controllers when the host system also enters an appropriate low-power state.
How much ESD protection does LTC1338CG provide?
The LTC1338CG provides ESD protection up to ±10 kV on its communications pins. The Analog Devices manufacturer datasheet states that both driver outputs and receiver inputs can survive multiple −10 kV ESD strikes and can be forced to −25V without damage. This internal protection is valuable on user-accessible ports, although external suppression may still be appropriate for long cables or severe industrial environments.
What happens when LTC1338CG enters shutdown mode?
Entering shutdown mode reduces the LTC1338CG supply current to 0.2 uA. The Analog Devices manufacturer datasheet distinguishes this figure from the 500 uA no-load operating current and the 50 uA receiver-alive current. Shutdown is useful for reducing power in portable or duty-cycled equipment, but system logic should ensure that the shutdown control state is defined during reset and power sequencing.
Where can I buy LTC1338CG and check price and lead time?
Use the Request a Quote form on this page to request current LTC1338CG pricing, stock, lead time, and order quantities. The form is the appropriate channel because inventory and commercial terms can change without notice. For technical validation, obtain the official Analog Devices datasheet and confirm the 28-pin SSOP footprint, commercial temperature grade, and LTC1338CG ordering designation before placing an order.
What is the price of LTC1338CG?
Current LTC1338CG pricing is handled through the Request a Quote form on this page rather than through a static price table. The manufacturer product page identifies the part as a production LTC1338 device, but a quantity-specific commercial quote should be used for purchasing decisions. When requesting a quote, specify the required quantity, acceptable packaging form, target delivery date, and whether any traceability documentation is needed.
What is the lead time for LTC1338CG?
The current lead time and available quantity for LTC1338CG should be requested through the Request a Quote form on this page. Lead time can vary with order size, packaging configuration, and supply conditions, so a direct engineering confirmation is more useful than a generic estimate. Include the production quantity, target date, and any required inspection or traceability documentation in the request.
Is LTC1338CG in stock?
Current LTC1338CG inventory should be confirmed through the Request a Quote form on this page. The Analog Devices manufacturer product page identifies the LTC1338 family as production, but that status alone does not guarantee a particular package suffix or quantity is immediately available. State the exact MPN and required quantity in the request so the quotation can reflect the correct 28-pin SSOP configuration.

Technische Referenzdaten für LTC1338CG – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LTC1338CG when a production design requires a commercial-grade, five-driver, three-receiver RS-232 transceiver in a 28-pin SSOP package. It is appropriate for legacy serial adapters, industrial panels, programmable test equipment, embedded controllers, and communication concentrators operating up to 120 kbaud. Choose LTC1338IG#PBF when the same mechanical and electrical interface is needed but the enclosure temperature requires the industrial-grade family option. The 500 uA no-load current and 0.2 uA shutdown current favor both parts for low-duty-cycle equipment, while the four 0.1 uF charge-pump capacitors simplify board area. No cross-brand drop-in alternative was verified with sufficient pin-level certainty, so a redesign should not be treated as a footprint-compatible substitution without a complete engineering review.

Vergleich mit Alternativen

Parameter Dieses Produkt LTC1338IG#PBF
Brand Analog Devices Analog Devices
Package 28-pin SSOP 28-pin SSOP
Product Type RS-232 transceiver RS-232 transceiver
Number of Drivers 5 5
Number of Receivers 3 3
Maximum Data Rate 120 kbaud 120 kbaud
Temperature Grade Commercial Industrial
No-Load Supply Current 500 uA 500 uA
Shutdown Supply Current 0.2 uA 0.2 uA
Charge-Pump Capacitors 4 x 0.1 uF 4 x 0.1 uF
ESD Protection ±10 kV ±10 kV
Special Feature Three-state driver outputs Three-state driver outputs

Wichtigste Unterscheidungsmerkmale

  • Combines five drivers and three receivers in one RS-232 interface IC (vs. LTC1338IG#PBF)
  • Supports low-power shutdown control (vs. LTC1338IG#PBF)
  • Integrates overvoltage and ESD resilience on serial lines (vs. LTC1338IG#PBF)
  • Uses a compact charge-pump implementation (vs. LTC1338IG#PBF)

Designhinweise

Place the four 0.1 uF charge-pump capacitors directly across their designated pins and keep the loops as short as practical. Follow the Analog Devices manufacturer datasheet connection diagram exactly because incorrect capacitor placement can degrade the charge-pump waveform and interface reliability. Add normal supply decoupling near the 5V and ground pins, and route connector-side signals away from sensitive logic traces to limit electrostatic-discharge current paths through the board.

Do not assume that the SSOP lead pitch matches a standard SOIC footprint. Confirm all 28 pad locations, pin numbering, and the exposed orientation against the manufacturer pin-description table before releasing artwork. Also verify that three-state driver control signals are defined during reset. Leaving the enable or shutdown state floating can create uncontrolled bus behavior even though the power rails remain within specification.

For cables longer than a short enclosure connection, add an appropriate connector-side protection network and controlled return path. The internal ±10 kV ESD rating should not be treated as a complete industrial surge solution. Keep the external protection return connection close to the connector ground, use low-inductance routing, and separate the protected interface area from switching regulators and high-current return paths to reduce noise entering the receiver channels.

Use shutdown mode deliberately when the equipment remains connected but idle. The 0.2 uA shutdown current is substantially below the 500 uA no-load operating current, so controlled shutdown can reduce standby consumption. Coordinate the state with the host controller so the transceiver is not disabled while the connected device is transmitting, and ensure external circuitry does not back-power an inactive line driver through connector protection paths.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer product information identifies the LTC1338 family as production, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established. AEC-Q100 is not applicable to this commercial communications interface IC.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LTC1338CG datasheet LTC1338CG datasheet pdf LTC1338CG pinout LTC1338CG equivalent LTC1338CG replacement LTC1338CG drop-in replacement LTC1338CG vs LTC1338IG#PBF Analog Devices LTC1338CG LTC1338CG 5V RS-232 transceiver LTC1338CG 120 kbaud interface LTC1338CG 28-pin SSOP LTC1338CG industrial control interface LTC1338CG price LTC1338CG stock where to buy LTC1338CG

Verwandte Bauteile & Begriffe

Analog Devices LTC1338CG LTC1338IG#PBF RS-232 RS-232 transceiver line transceiver interface IC semiconductor five-driver transceiver three-receiver transceiver single 5V supply charge-pump voltage conversion 120 kbaud 500 uA no-load supply current 0.2 uA shutdown current ±10 kV ESD protection three-state outputs 28-pin SSOP SSOP package family surface-mount technology legacy serial communication industrial control programmable test equipment portable service interface
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen