LTC1338CG - 5V Low-Power RS-232 Transceiver | Analog Devices
MPN: LTC1338CG ✓ सक्रियLTC1338CG अवलोकन
An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 equipment. The LTC1338 belongs to the transceiver hierarchy, where a complete interface IC combines line drivers, receivers, charge-pump voltage conversion, and sometimes shutdown control. It is designed for compact serial-port equipment where low supply current, limited board area, and robust electrostatic protection are important.
Five driver outputs support multiple RS-232 channels or control signals, while three receiver inputs support three incoming data or handshake signals. Three-state driver outputs allow the drivers to be disconnected when the bus direction changes. The 120 kbaud capability accommodates legacy communications, industrial controllers, service interfaces, and equipment-control links without requiring a separate external charge-pump supply.
The single 5V architecture simplifies power-system design because the device generates the RS-232 bipolar levels internally. Its low 500 uA no-load supply current reduces standby demand, and the 0.2 uA shutdown current is valuable in portable or intermittently powered instruments. Driver outputs and receiver inputs withstand forced voltages down to −25V without damage, adding protection margin on externally accessible connectors.
Typical uses include legacy serial-port adapters, programmable test equipment, industrial control panels, embedded service interfaces, and communication links between older RS-232 peripherals and modern controller boards. The 28-pin SSOP package supports surface-mount assembly but requires careful handling because the lead pitch is narrower than that of a standard SOIC.
Designers should connect the four 0.1 uF charge-pump capacitors exactly as shown in the manufacturer application information, place them close to the associated pins, and provide adequate bypass capacitance at the supply pins. External protection should supplement the internal ±10 kV ESD rating when cables extend beyond the enclosure or connect to industrial environments.
This page consolidates the device’s principal electrical characteristics, package information, application fit, and verified substitution status. The comparison and design notes emphasize the practical trade-offs that matter when replacing an RS-232 interface without changing the PCB footprint.
के लिए ड्रॉप-इन विकल्प LTC1338CG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
LTC1338IG#PBF
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LTC1338CG विशेषताएं
| Product Type | RS-232 transceiver |
| Number of Drivers | 5 |
| Number of Receivers | 3 |
| सप्लाई वोल्टेज | 5 V |
| No-Load Supply Current | 500 uA |
| Shutdown Supply Current | 0.2 uA |
| Receiver-Alive Supply Current | 50 uA |
| Maximum Data Rate | 120 kbaud |
| Charge-Pump Capacitors | 4 x 0.1 uF |
| ESD Protection | ±10 kV |
| Driver Output Overvoltage Tolerance | −25 V |
| Receiver Input Overvoltage Tolerance | −25 V |
| Driver Output States | 3-state |
| पैकेज | 28-pin SSOP |
| Temperature Grade | Commercial |
| माउंटिंग प्रकार | Surface Mount |
LTC1338CG 28-pin ssop पिन कॉन्फ़िगरेशन गाइड
LTC1338CG (28-pin ssop पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LTC1338CG.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LTC1338CG के लिए उपयुक्त है 6 अनुप्रयोगs: Legacy Serial-Port Adapters, Industrial Control Panels, Programmable Test Equipment, Portable Service Interfaces, Embedded Equipment Control, Communication Port Concentrators.
Legacy Serial-Port Adapters
The LTC1338CG fits legacy serial-port adapters because it combines five RS-232 drivers and three receivers with operation from a single 5V supply. Up to 120 kbaud support covers many legacy peripherals while the 500 uA no-load current limits standby demand. Four 0.1 uF charge-pump capacitors keep the auxiliary circuit compact, and the 28-pin SSOP package suits adapter boards where connector clearance is limited. The three-state outputs also help a controller-managed interface avoid bus contention during direction changes.
अनुशंसित
Industrial Control Panels
The LTC1338CG is useful in industrial control panels that retain RS-232 links to older drives, printers, or service equipment. Its five-driver and three-receiver arrangement supports both data and handshake signals, while 120 kbaud operation provides compatibility with conventional control protocols. Internal ±10 kV ESD protection improves robustness at accessible connectors, although panel-level surge protection may still be required. The low-power architecture also suits controllers that remain powered while the external equipment is idle.
अनुशंसित
Programmable Test Equipment
The LTC1338CG can support programmable test equipment that communicates with legacy instruments through RS-232. The five-driver and three-receiver configuration accommodates several control and measurement signals without requiring multiple single-channel transceivers. A maximum rate of 120 kbaud supports older automated-test protocols, while shutdown current of 0.2 uA helps conserve energy between test cycles. The SSOP package reduces board area, although careful assembly practices are necessary because of its narrow lead spacing.
अनुशंसित
Portable Service Interfaces
The LTC1338CG is appropriate for portable service interfaces because its 500 uA no-load current and 0.2 uA shutdown current reduce demand when the equipment is idle. A single 5V rail simplifies power design, while the integrated charge pump avoids a separate negative supply. The five available drivers can carry multiple control signals, and the three receivers can monitor responses from a peripheral. At the connector, the internal ±10 kV ESD rating provides a useful baseline, with additional external protection advisable for field cables.
अनुशंसित
Embedded Equipment Control
The LTC1338CG suits embedded controllers that must communicate with external RS-232 actuators or instruments. Three receivers allow the controller to monitor device status, acknowledgments, and interlock signals, while five drivers support command and handshake outputs. Its 120 kbaud limit accommodates many embedded control protocols, and the three-state outputs provide a controlled way to disable drivers when the interface direction changes. Single-supply operation also reduces rail complexity in compact control assemblies.
अनुशंसित
Communication Port Concentrators
The LTC1338CG can participate in communication port concentrators that adapt legacy equipment to a modern controller. The five drivers and three receivers allow several RS-232 lines to share one interface IC, reducing component count compared with separate single-channel devices. Operation to 120 kbaud and compliance with RS-232 data-rate requirements preserve legacy connectivity. The 28-pin SSOP footprint supports compact concentrator boards, while shutdown control can reduce consumption when a managed port is not active.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LTC1338CG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LTC1338IG#PBF |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP |
| Product Type | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 5 | 5 |
| Number of Receivers | 3 | 3 |
| Maximum Data Rate | 120 kbaud | 120 kbaud |
| Temperature Grade | Commercial | Industrial |
| No-Load Supply Current | 500 uA | 500 uA |
| Shutdown Supply Current | 0.2 uA | 0.2 uA |
| Charge-Pump Capacitors | 4 x 0.1 uF | 4 x 0.1 uF |
| ESD Protection | ±10 kV | ±10 kV |
| Special Feature | Three-state driver outputs | Three-state driver outputs |
मुख्य विशेषताएँ
- Combines five drivers and three receivers in one RS-232 interface IC (बनामLTC1338IG#PBF)
- Supports low-power shutdown control (बनामLTC1338IG#PBF)
- Integrates overvoltage and ESD resilience on serial lines (बनामLTC1338IG#PBF)
- Uses a compact charge-pump implementation (बनामLTC1338IG#PBF)
डिज़ाइन नोट्स
Place the four 0.1 uF charge-pump capacitors directly across their designated pins and keep the loops as short as practical. Follow the Analog Devices manufacturer datasheet connection diagram exactly because incorrect capacitor placement can degrade the charge-pump waveform and interface reliability. Add normal supply decoupling near the 5V and ground pins, and route connector-side signals away from sensitive logic traces to limit electrostatic-discharge current paths through the board.
Do not assume that the SSOP lead pitch matches a standard SOIC footprint. Confirm all 28 pad locations, pin numbering, and the exposed orientation against the manufacturer pin-description table before releasing artwork. Also verify that three-state driver control signals are defined during reset. Leaving the enable or shutdown state floating can create uncontrolled bus behavior even though the power rails remain within specification.
For cables longer than a short enclosure connection, add an appropriate connector-side protection network and controlled return path. The internal ±10 kV ESD rating should not be treated as a complete industrial surge solution. Keep the external protection return connection close to the connector ground, use low-inductance routing, and separate the protected interface area from switching regulators and high-current return paths to reduce noise entering the receiver channels.
Use shutdown mode deliberately when the equipment remains connected but idle. The 0.2 uA shutdown current is substantially below the 500 uA no-load operating current, so controlled shutdown can reduce standby consumption. Coordinate the state with the host controller so the transceiver is not disabled while the connected device is transmitting, and ensure external circuitry does not back-power an inactive line driver through connector protection paths.
अनुपालन जानकारी
The manufacturer product information identifies the LTC1338 family as production, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established. AEC-Q100 is not applicable to this commercial communications interface IC.