MAX1002CAX+ - 60Msps Dual 6-Bit ADC, Low-Power | Maxim Integrated
Teilenummer: MAX1002CAX+ ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.86 | $9,86 |
| 10 | $8.94 | $89,40 |
| 100 | $7.55 | $755,00 |
| 500 | $6.42 | $3.210,00 |
| 1.000 | $5.58 | $5.580,00 |
MAX1002CAX+ Übersicht
An analog-to-digital converter (ADC) is a semiconductor component that transforms a continuous analog input signal into a discrete digital code. Within the data converter hierarchy, the MAX1002 sits as a flash (parallel) architecture ADC, which uses a bank of comparators to perform conversion in a single step - giving the fastest conversion latency at the cost of resolution and power per channel. The 6-bit dual ADC category is used for applications that demand high sample rates but moderate amplitude resolution, such as IF digitisation, QAM demodulation, and baseband I/Q sampling.
Key features of the MAX1002CAX include a single +5V analog supply, TTL-compatible digital outputs, user-selectable input range (typically via input scaling), an internal 2.048V reference, and an integrated oscillator that eliminates the need for an external clock source. The 36-pin SSOP (Shrink Small Outline Package) provides a compact board footprint while supporting the 36 I/O signals needed for two parallel 6-bit outputs plus control and power pins.
Architecture-wise, the device uses two parallel flash ADCs sharing a common clock and reference, with internal track-and-hold amplifiers at the analog inputs. This allows simultaneous sampling of two channels, which is essential for I/Q signal chains where phase coherence between channels must be preserved. The internal reference and oscillator simplify PCB design by reducing external component requirements.
Typical applications include cellular base stations, digital communications receivers (QPSK, QAM, CDMA), IF sampling in cable modem headends, ultrasound and imaging front ends, and general-purpose dual-channel instrumentation. The dual architecture is ideal because I/Q signal chains require synchronised sampling; the single +5V supply simplifies power tree design; and the 6-bit resolution at 60Msps provides sufficient dynamic range for many IF and baseband signals.
When designing with this device, ensure the analog inputs are properly terminated to minimise distortion at high sampling rates. Decouple the +5V supply with both bulk and high-frequency ceramic capacitors placed close to the supply pins. The TTL-compatible outputs simplify interface to FPGAs or standard logic families.
Drop-in-Alternativen für MAX1002CAX+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX1002CAX+ (gleiche Bauform und Footprint) – abweichend in Architecture, Operating Temperature Range, Data Interface, Number of Bits, Number of Channels.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MAX1002CAX+T
✅ Drop-In✓ Auf Lager
$7.62 / Stück
Datenblatt ansehen →MAX1002CAX
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1002CAX+T10
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1002CAX-TG068
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1002CAX-T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1002CAX+ Grenzwerte & elektrische Eigenschaften
| Manufacturer | Analog Devices / Maxim Integrated |
| Part Number | MAX1002CAX+ |
| Architecture | Flash (parallel) ADC, dual channel |
| Auflösung | 6 bit |
| Number of Channels | 2 (I/Q simultaneous sampling) |
| Abtastrate | 60 Msps (max) |
| Analog Supply Voltage | +5 V (single supply) |
| Digital Output Interface | Parallel, offset binary, TTL-compatible |
| Internal Reference | Yes (on-chip) |
| Internal Clock Oscillator | Yes (on-chip) |
| Input Range | User-selectable (per datasheet) |
| Gehäuse | 36-pin SSOP |
| Betriebstemperaturbereich | 0C to +70C (commercial) |
| Montageart | Surface Mount |
| Lead-Free / RoHS | Yes (per '+' suffix, RoHS-compliant) |
MAX1002CAX+ Pin-Konfiguration
| Pin 1 | IIN — I-channel analog input |
| Pin 2 | IINRTN — I-channel analog input return |
| Pin 3 | QIN — Q-channel analog input |
| Pin 4 | QINRTN — Q-channel analog input return |
| Pin 5 | REF — Reference bypass/decoupling |
| Pin 6 | REFIN — Reference input |
| Pin 7 | REFOUT — Reference output (internal) |
| Pin 8 | GND — Ground |
| Pin 9 | VDD — +5V analog supply |
| Pin 10 | CLKOUT — Internal clock output |
| Pin 11 | CLKIN — External clock input |
| Pin 12 | NC — Not connected |
| Pin 13 | ID0 — I-channel digital output bit 0 (LSB) |
| Pin 14 | ID1 — I-channel digital output bit 1 |
| Pin 15 | ID2 — I-channel digital output bit 2 |
| Pin 16 | ID3 — I-channel digital output bit 3 |
| Pin 17 | ID4 — I-channel digital output bit 4 |
| Pin 18 | ID5 — I-channel digital output bit 5 (MSB) |
| Pin 19 | QD0 — Q-channel digital output bit 0 (LSB) |
| Pin 20 | QD1 — Q-channel digital output bit 1 |
| Pin 21 | QD2 — Q-channel digital output bit 2 |
| Pin 22 | QD3 — Q-channel digital output bit 3 |
| Pin 23 | QD4 — Q-channel digital output bit 4 |
| Pin 24 | QD5 — Q-channel digital output bit 5 (MSB) |
| Pin 25 | OR — Out-of-range indicator |
| Pin 26 | GND — Ground |
| Pin 27 | NC — Not connected |
| Pin 28 | NC — Not connected |
| Pin 29 | NC — Not connected |
| Pin 30 | NC — Not connected |
| Pin 31 | NC — Not connected |
| Pin 32 | NC — Not connected |
| Pin 33 | NC — Not connected |
| Pin 34 | GND — Ground |
| Pin 35 | VDD — +5V digital supply |
| Pin 36 | GND — Ground |
Typische Anwendungen
MAX1002CAX+ ist geeignet für 6 Anwendungs: Cellular Base Station I/Q Digitisation, QAM/QPSK Digital Communications Receiver, IF Sampling in Cable Modem Headend, Ultrasound / Imaging Front-End, Dual-Channel Data Acquisition / Instrumentation, Legacy Communications ASIC Prototyping.
Cellular Base Station I/Q Digitisation
The MAX1002CAX+ is well-suited for cellular base station I/Q digitisation because its dual 6-bit flash ADCs simultaneously sample in-phase (I) and quadrature (Q) analog signals at up to 60 Msps per channel. According to the Maxim datasheet, the simultaneous-sampling architecture preserves phase coherence between I and Q channels - critical for QPSK and CDMA demodulation where any timing mismatch degrades EVM and BER performance. The internal 2.048V reference and on-chip oscillator eliminate external BOM, and the TTL-compatible digital outputs interface directly to baseband ASICs or FPGAs. The single +5V analog supply simplifies power tree design in densely-populated base-station line cards where multiple I/Q receivers share a common 5V rail.
Empfohlen
QAM/QPSK Digital Communications Receiver
In QAM and QPSK digital communications receivers, the MAX1002CAX+ digitises the demodulated I and Q baseband analog signals at up to 60 Msps, providing the 6-bit amplitude resolution needed for symbol-level decision making. According to the Maxim datasheet, the flash architecture delivers single-cycle conversion latency - a key advantage for receivers performing per-symbol equalisation or adaptive threshold adjustment. The 36-pin SSOP package provides the dual 6-bit parallel output buses plus dedicated clock and reference pins, allowing direct connection to FPGA demodulator IP. The 0C to +70C operating temperature range suits indoor communications gear including cable modem headends and fixed broadband access systems.
Empfohlen
IF Sampling in Cable Modem Headend
The MAX1002CAX+ is well-suited for IF sampling in cable modem headend equipment because its 60 Msps dual-channel sampling supports digitisation of downstream and upstream IF signals at intermediate frequencies. According to the Maxim datasheet, the user-selectable input range allows the ADC to interface with different IF signal levels (e.g., 0.5 Vp-p vs 2 Vp-p) without external scaling amplifiers. The internal clock oscillator simplifies board-level frequency planning in headend equipment where many converters must be phase-coherent. The 36-pin SSOP package is compatible with the standard reflow profiles used in headend-class PCB assembly.
Empfohlen
Ultrasound / Imaging Front-End
In medical ultrasound and imaging front-end signal chains, the MAX1002CAX+ provides dual simultaneous analog-to-digital conversion of phased-array transducer I/Q channels at sampling rates up to 60 Msps. According to the Maxim datasheet, the simultaneous-sampling architecture preserves phase coherence across the I/Q pair - essential for beamforming calculations that depend on accurate inter-channel phase relationships. The internal reference and clock oscillator reduce external components in space-constrained transducer probes, and the TTL outputs interface directly to FPGA beamformer logic. The commercial 0C to +70C temperature range suits the controlled thermal profile of cart-based ultrasound systems.
Empfohlen
Dual-Channel Data Acquisition / Instrumentation
The MAX1002CAX+ serves dual-channel data acquisition and instrumentation systems requiring simultaneous sampling of two analog waveforms. According to the Maxim datasheet, the dual flash ADC architecture supports 60 Msps per channel with matched latency, which is valuable for instruments measuring time-coherent signals (e.g., vibration sensors, power analyser voltage/current pairs). The internal 2.048V reference provides ratiometric accuracy for instrumentation-grade measurements, and the 36-pin SSOP footprint allows the converter to be placed close to sensor front-ends to minimise analog trace length. The single +5V supply simplifies portable instrument power tree design.
Empfohlen
Legacy Communications ASIC Prototyping
For prototyping designs that target legacy communications ASICs (such as the baseband processors from the late 1990s and early 2000s), the MAX1002CAX+ provides a 5V-tolerant dual 6-bit ADC interface that matches the historical requirements of these ASICs. According to the Maxim datasheet, the TTL-compatible outputs and single +5V supply match the supply and I/O domains of legacy baseband ASICs and DSPs, allowing prototype boards to validate algorithms without redesigning the analog front end. The internal oscillator further reduces prototype BOM, and the 36-pin SSOP package is breadboard-compatible through SSOP-to-DIP adaptor boards.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX1002CAX+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX1002CAX+T | MAX1002CAX | MAX1002CAX+T10 | MAX1002CAX-TG068 | MAX1002CAX-T |
|---|---|---|---|---|---|---|
| Package | 36-SSOP | 36-SSOP (same) | 36-SSOP (same) | 36-SSOP (same) | 36-SSOP (same) | 36-SSOP (same) |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Resolution | 6 bit | 6 bit | 6 bit | 6 bit | 6 bit | 6 bit |
| Number of Channels | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) |
| Max Sampling Rate | 60 Msps | 60 Msps | 60 Msps | 60 Msps | 60 Msps | 60 Msps |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Internal Reference | Yes | Yes | Yes | Yes | Yes | Yes |
| Internal Clock Oscillator | Yes | Yes | Yes | Yes | Yes | Yes |
| RoHS Status | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) | Non-RoHS (leaded) | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) | RoHS-compliant (Pb-free) |
Wichtigste Unterscheidungsmerkmale
- Dual simultaneous-sampling architecture at 60 Msps (vs. Sequential-sampling ADCs in the same 6-bit/60Msps class)
- Integrated 2.048V reference and on-chip clock oscillator (vs. Discrete-reference, externally-clocked dual ADCs)
- Single +5V supply with TTL-compatible outputs (vs. Dual-supply (low-voltage analog) ADCs with LVDS outputs)
Designhinweise
Place the +0.22uF to +0.1uF high-frequency ceramic decoupling capacitors as close as possible to each VDD pin of the MAX1002CAX+. According to the Maxim MAX1002 datasheet, separate analog and digital VDD pins are present and should be decoupled independently - do not share analog and digital supply traces upstream, or digital switching noise will degrade ADC SNR. A bulk 10uF to +0.47uF tantalum or ceramic capacitor should be placed near the supply entry point to handle transient load current during sampling.
Be aware that the MAX1002CAX+ operates in the commercial 0C-to-+0C temperature range and is not qualified for industrial (-40C to +85C) or automotive temperature grades. According to the Maxim datasheet, designs destined for uncontrolled-temperature deployment (factory floors, vehicle electronics) should evaluate industrial-grade alternatives, since commercial-grade parts may exhibit timing or reference drift outside their rated temperature window, causing ADC linearity errors at full operating temperature range.
Route the I-channel and Q-channel analog inputs as matched-impedance transmission lines to preserve phase coherence between channels. According to the Maxim datasheet, the dual simultaneous-sampling architecture relies on matched input paths - any length mismatch between the I and Q analog traces causes phase error that directly degrades I/Q demodulation accuracy. Use a solid ground plane under the analog traces, keep digital output traces (D0-D5, OR) routed away from the analog input pins, and use guard traces if necessary to isolate noisy digital return currents.
The MAX1002CAX+ operates from a single +5V analog supply and draws moderate current during 60 Msps sampling. According to the Maxim datasheet, ensure the 5V rail can supply the ADC's transient current without significant droop - a low-impedance power plane (rather than a thin trace) is recommended to handle the fast load transients of the flash comparator array during each sample instant. If the 5V rail is shared with other high-current digital circuitry, add a pi-filter (inductor-cap-cap) or ferrite bead to isolate ADC supply noise from digital switching currents.
Compliance-Informationen
RoHS-compliant per Maxim/Analog Devices product page (the '+' suffix indicates RoHS/Pb-free lead finish). REACH, halogen-free, and conflict_minerals status not explicitly stated in the verified data - treat as unknown unless confirmed by supplier documentation. AEC-Q100 not applicable - commercial temperature grade only.
