MAX14803CXB+T - 16-Channel 48 Ohm SPST Switch | Maxim
Teilenummer: MAX14803CXB+T ✓ AktivMAX14803CXB+T Übersicht
An analog switch IC is a semiconductor interface device that uses control inputs to connect or disconnect signal paths. The MAX14803CXB+T combines 16 circuits with SPST switch characteristics, as identified in the manufacturer-related product information. Its 1:1 configuration describes a single-pole, single-throw arrangement in which one switched path is selected for each controlled connection. This makes the device relevant to designs that require multiple controllable signal routes rather than a single isolated connection.
The confirmed 48 ohm on-resistance is the central electrical parameter for design evaluation. Lower resistance generally reduces signal attenuation and improves drive capability, while higher resistance can affect voltage margins, bandwidth, and power loss. Designers should compare this value against the source impedance, load impedance, signal amplitude, switching frequency, and acceptable insertion loss required by the target system. The selected MAX14803CXB+T has 16 circuits and a 1:1 configuration, providing the basis for multi-channel routing.
This integrated switch is intended for applications where several external or internal signal paths must be selected under digital control. Potential uses include test and measurement systems, data-acquisition equipment, industrial control interfaces, battery or power-system monitoring, and instrumentation in which many analog inputs share downstream circuitry. The SPST behavior is useful when a selected channel must be isolated while disconnected, helping reduce unintended signal interaction between channels.
Integration can simplify system routing by replacing numerous discrete mechanical or semiconductor switches. A multiplexed approach reduces the number of external connections reaching a processor, amplifier, or data converter. The practical benefit depends on the complete signal chain: channel resistance, capacitance, control timing, leakage, voltage tolerance, and the behavior of the load all influence whether multiplexing improves or degrades measurement accuracy.
When designing a PCB around the MAX14803CXB+T, preserve the package footprint and pin assignments defined by the manufacturer datasheet. Confirm every signal amplitude and common-mode range, including maximum transients, before routing connector or sensor inputs into the device. Use short, protected traces where possible, maintain a defined ground reference, and account for unused control inputs. A common-mode range and detailed pin map must be checked in the manufacturer documentation before layout release.
This page consolidates the confirmed 16-circuit configuration, 1:1 SPST characteristics, 48 ohm on-resistance, tape-and-reel ordering notation, sourcing information, and practical integration guidance into a focused engineering reference. It also distinguishes verified drop-in replacements from generic multiplexers so procurement and PCB decisions are based on actual compatibility rather than package-name similarity.
Drop-in-Alternativen für MAX14803CXB+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernMAX14803CXB+T Grenzwerte & elektrische Eigenschaften
| Product Type | 16-circuit IC switch |
| Circuit Count | 16 circuits |
| Switch Configuration | 1:1 |
| On-Resistance | 48 ohm |
| Switch Type | SPST |
| Circuit Function | Multiplexer |
| Montageart | Surface mount |
| Packaging | Tape & Reel |
| RoHS-Status | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Unknown |
MAX14803CXB+T standard Pinbelegungsleitfaden
Pinbelegung für MAX14803CXB+T (standard-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX14803CXB+T.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX14803CXB+T ist geeignet für 6 Anwendungs: Automated Test Systems, Data Acquisition Equipment, Industrial Control Interfaces, Battery and Power-System Monitoring, Programmable Signal Conditioning, Communications and RF Test Harnesses.
Automated Test Systems
The MAX14803CXB+T can route multiple test channels through a shared measurement path because it provides 16 SPST circuits with a 1:1 configuration. Its 48 ohm on-resistance must be included when calculating attenuation between the source, switch, and input impedance of the tester. This arrangement is useful when reducing the number of front-panel connections reaching amplifiers, data converters, or acquisition circuits. Confirm control timing, signal limits, and grounding against the manufacturer datasheet before implementing the matrix.
Data Acquisition Equipment
For multi-channel data acquisition, the 16-circuit MAX14803CXB+T offers a compact way to multiplex analog inputs into downstream conversion circuitry. The 48 ohm on-resistance can combine with high-impedance sensor outputs and input capacitance to create settling-time and attenuation effects. Use the switch only when its resistance and switching characteristics fit the required measurement accuracy. Keep high-impedance traces short and guard against leakage, connector transients, and control-input coupling during board layout.
Industrial Control Interfaces
The MAX14803CXB+T is applicable to industrial routing circuits that require 16 independently controlled SPST paths in a compact surface-mount package. A 1:1 configuration supports connection and isolation of multiple external or internal nodes while preserving a consistent channel model. The 48 ohm path resistance should be checked against actuator, sensor, and logic levels to ensure adequate voltage margins. Validate industrial temperature, surge, and transient requirements in the manufacturer electrical characteristics before production release.
Battery and Power-System Monitoring
A multi-cell monitoring design can use the 16 SPST circuits of the MAX14803CXB+T to isolate or connect measurement channels when the required signal and control limits are met. Its 48 ohm on-resistance is significant in battery systems because sensing paths often have high source impedance and limited voltage headroom. Engineer the divider formed by the switch and input network so measurement error remains acceptable. Confirm the maximum signal magnitude, control thresholds, leakage, and operating temperature before using the device in battery applications.
Programmable Signal Conditioning
The MAX14803CXB+T can select among several conditioning paths before amplifiers or filters in a programmable instrument. With 16 circuits and 48 ohm on-resistance, it offers useful channel density while maintaining identifiable SPST isolation behavior. The switch resistance affects gain and offset calculations when paired with finite input impedances, while off leakage can influence high-impedance nodes. Use short traces, controlled return paths, and suitable protection networks where connector inputs can encounter transient voltages.
Communications and RF Test Harnesses
Communications and RF test harnesses may use the 16 SPST paths of the MAX14803CXB+T for controlled routing between sources, loads, and instrumentation. The 1:1 architecture keeps each selected route conceptually simple, while the 48 ohm on-resistance must be incorporated into insertion-loss and source-to-load impedance calculations. Confirm frequency-dependent behavior in the manufacturer datasheet before using the switch for high-speed signals. Connector isolation, transient protection, and grounding should be designed around the selected operating voltage and channel topology.
Technische Referenzdaten für MAX14803CXB+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Circuit Count | 16 circuits |
| Switch Configuration | 1:1 |
| Switch Type | SPST |
| On-Resistance | 48 ohm |
| Brand | Maxim Integrated |
Designhinweise
Include the 48 ohm on-resistance in the complete source-switch-load network rather than treating it as an isolated component value. Calculate the resulting voltage division with the actual source and load impedances, then verify settling and bandwidth requirements. If the selected channel drives a high-impedance amplifier, assess leakage and capacitance effects as well.
Route switched signals using short traces and a continuous ground reference to minimize coupling between the 16 channels. Keep connector and protection-network connections away from control traces where practical. Before routing the PCB, verify the CXB land pattern, pin numbering, exposed-pad requirements, and no-connect instructions in the manufacturer package drawing.
Do not select a replacement solely because it is described as a 16-channel SPST mux. A drop-in device must match the CXB footprint, pin assignments, control levels, signal limits, switching timing, leakage, and package tolerances. Confirm the complete ordering suffix and tape-and-reel orientation during component procurement and incoming inspection.
Compliance-Informationen
Material-compliance status was not confirmed for the exact MAX14803CXB+T ordering code. Request the current manufacturer declarations before release to RoHS-, REACH-, or automotive-controlled production.