Maxim Integrated

MAX14803CXB+T - 16-Channel 48 Ohm SPST Switch | Maxim

MPN: MAX14803CXB+T ✓ Nakahanda
48 ohm Rds(on)
MOQ: 1 |

MAX14803CXB+T Ulas

The Maxim Integrated MAX14803CXB+T is a 16-circuit integrated analog switch with a 1:1 configuration and 48 ohm on-resistance. It is supplied in a tape-and-reel package identified by the +T ordering suffix. The device belongs to the broader category of analog switch ICs, which route controlled signals between circuit nodes while helping isolate external equipment from internal signal paths.

An analog switch IC is a semiconductor interface device that uses control inputs to connect or disconnect signal paths. The MAX14803CXB+T combines 16 circuits with SPST switch characteristics, as identified in the manufacturer-related product information. Its 1:1 configuration describes a single-pole, single-throw arrangement in which one switched path is selected for each controlled connection. This makes the device relevant to designs that require multiple controllable signal routes rather than a single isolated connection.

The confirmed 48 ohm on-resistance is the central electrical parameter for design evaluation. Lower resistance generally reduces signal attenuation and improves drive capability, while higher resistance can affect voltage margins, bandwidth, and power loss. Designers should compare this value against the source impedance, load impedance, signal amplitude, switching frequency, and acceptable insertion loss required by the target system. The selected MAX14803CXB+T has 16 circuits and a 1:1 configuration, providing the basis for multi-channel routing.

This integrated switch is intended for applications where several external or internal signal paths must be selected under digital control. Potential uses include test and measurement systems, data-acquisition equipment, industrial control interfaces, battery or power-system monitoring, and instrumentation in which many analog inputs share downstream circuitry. The SPST behavior is useful when a selected channel must be isolated while disconnected, helping reduce unintended signal interaction between channels.

Integration can simplify system routing by replacing numerous discrete mechanical or semiconductor switches. A multiplexed approach reduces the number of external connections reaching a processor, amplifier, or data converter. The practical benefit depends on the complete signal chain: channel resistance, capacitance, control timing, leakage, voltage tolerance, and the behavior of the load all influence whether multiplexing improves or degrades measurement accuracy.

When designing a PCB around the MAX14803CXB+T, preserve the package footprint and pin assignments defined by the manufacturer datasheet. Confirm every signal amplitude and common-mode range, including maximum transients, before routing connector or sensor inputs into the device. Use short, protected traces where possible, maintain a defined ground reference, and account for unused control inputs. A common-mode range and detailed pin map must be checked in the manufacturer documentation before layout release.

This page consolidates the confirmed 16-circuit configuration, 1:1 SPST characteristics, 48 ohm on-resistance, tape-and-reel ordering notation, sourcing information, and practical integration guidance into a focused engineering reference. It also distinguishes verified drop-in replacements from generic multiplexers so procurement and PCB decisions are based on actual compatibility rather than package-name similarity.

Mga alternatibo na pwedeng ilagay na MAX14803CXB+T — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Wala ng magagamit na drop-in alternatibo para sa produkto na ito.

Hilingin ang Alternatibo

MAX14803CXB+T Mga Pinakamataas na Rating at Electrical Characteristics

Product Type 16-circuit IC switch
Circuit Count 16 circuits
Switch Configuration 1:1
On-Resistance 48 ohm
Switch Type SPST
Circuit Function Multiplexer
Uri ng Pagpapasok Surface mount
Packaging Tape & Reel
Tindminan RoHS Unknown
REACH Status Unknown
AEC-Q100 Qualification Unknown

Gabay sa Pin Configuration ng MAX14803CXB+T standard

Pin configuration para sa MAX14803CXB+T (standard package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng standard package para sa MAX14803CXB+T

Wala ng detalyadong pinout data na magagamit para sa MAX14803CXB+T.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MAX14803CXB+T ay nararapat para sa 6 aplikasyons: Automated Test Systems, Data Acquisition Equipment, Industrial Control Interfaces, Battery and Power-System Monitoring, Programmable Signal Conditioning, Communications and RF Test Harnesses.

🖥️

Automated Test Systems

The MAX14803CXB+T can route multiple test channels through a shared measurement path because it provides 16 SPST circuits with a 1:1 configuration. Its 48 ohm on-resistance must be included when calculating attenuation between the source, switch, and input impedance of the tester. This arrangement is useful when reducing the number of front-panel connections reaching amplifiers, data converters, or acquisition circuits. Confirm control timing, signal limits, and grounding against the manufacturer datasheet before implementing the matrix.

📊

Data Acquisition Equipment

For multi-channel data acquisition, the 16-circuit MAX14803CXB+T offers a compact way to multiplex analog inputs into downstream conversion circuitry. The 48 ohm on-resistance can combine with high-impedance sensor outputs and input capacitance to create settling-time and attenuation effects. Use the switch only when its resistance and switching characteristics fit the required measurement accuracy. Keep high-impedance traces short and guard against leakage, connector transients, and control-input coupling during board layout.

🏭

Industrial Control Interfaces

The MAX14803CXB+T is applicable to industrial routing circuits that require 16 independently controlled SPST paths in a compact surface-mount package. A 1:1 configuration supports connection and isolation of multiple external or internal nodes while preserving a consistent channel model. The 48 ohm path resistance should be checked against actuator, sensor, and logic levels to ensure adequate voltage margins. Validate industrial temperature, surge, and transient requirements in the manufacturer electrical characteristics before production release.

⚡

Battery and Power-System Monitoring

A multi-cell monitoring design can use the 16 SPST circuits of the MAX14803CXB+T to isolate or connect measurement channels when the required signal and control limits are met. Its 48 ohm on-resistance is significant in battery systems because sensing paths often have high source impedance and limited voltage headroom. Engineer the divider formed by the switch and input network so measurement error remains acceptable. Confirm the maximum signal magnitude, control thresholds, leakage, and operating temperature before using the device in battery applications.

🔧

Programmable Signal Conditioning

The MAX14803CXB+T can select among several conditioning paths before amplifiers or filters in a programmable instrument. With 16 circuits and 48 ohm on-resistance, it offers useful channel density while maintaining identifiable SPST isolation behavior. The switch resistance affects gain and offset calculations when paired with finite input impedances, while off leakage can influence high-impedance nodes. Use short traces, controlled return paths, and suitable protection networks where connector inputs can encounter transient voltages.

🌐

Communications and RF Test Harnesses

Communications and RF test harnesses may use the 16 SPST paths of the MAX14803CXB+T for controlled routing between sources, loads, and instrumentation. The 1:1 architecture keeps each selected route conceptually simple, while the 48 ohm on-resistance must be incorporated into insertion-loss and source-to-load impedance calculations. Confirm frequency-dependent behavior in the manufacturer datasheet before using the switch for high-speed signals. Connector isolation, transient protection, and grounding should be designed around the selected operating voltage and channel topology.

What is the MAX14803CXB+T?
The MAX14803CXB+T is a 16-circuit integrated switch with a 1:1 configuration, SPST switching characteristics, and 48 ohm on-resistance. According to the manufacturer datasheet, it is a multiplexed analog switch intended to route multiple controlled signal paths while supporting isolation in the off state. The +T ordering suffix identifies the tape-and-reel shipping format.
What are the key specifications of MAX14803CXB+T?
The key confirmed specifications are 16 circuits, a 1:1 switch configuration, SPST operation, and 48 ohm on-resistance. These parameters define the device as a multi-channel analog switching component rather than a single switch. The MAX14803CXB+T is ordered in tape-and-reel format. Consult the manufacturer pin table and electrical characteristics before assigning supply, control, and signal pins.
What is the on-resistance of MAX14803CXB+T?
The MAX14803CXB+T has a specified on-resistance of 48 ohm. This value is important when the device carries analog signals because resistance combines with source and load impedance to create voltage division. According to the manufacturer datasheet, design calculations should include the complete source impedance, selected load, and permissible attenuation for the signal being routed.
Is MAX14803CXB+T a multiplexer or a single switch?
The MAX14803CXB+T is a 16-circuit multiplexing analog switch rather than a single discrete switch. Its 1:1 configuration identifies the SPST path arrangement, allowing multiple channels to share downstream circuitry. The 48 ohm on-resistance applies to the switched signal path, so channel selection should be included in signal-integrity and measurement-error calculations.
Where can I download the MAX14803CXB+T datasheet PDF?
The MAX14803CXB+T datasheet PDF is available through the datasheet link listed on this product page. Use the document’s pin-description table to verify signal, ground, supply, and control assignments before laying out a PCB. Also check the absolute maximum ratings and recommended operating conditions before applying external voltages or connector-referenced signals.
Where can I find the MAX14803CXB+T pinout?
The MAX14803CXB+T pinout is assigned by the manufacturer datasheet and must be checked against the exact CXB package drawing. Before routing the PCB, use the pin-description table for every numbered terminal and confirm exposed-pad or no-connect instructions where applicable. The package mark and lead orientation should also be checked during assembly inspection.
What can replace the MAX14803CXB+T?
A drop-in replacement must use the exact CXB footprint, preserve the same pin assignments, and provide comparable 16-circuit SPST switching with an on-resistance close to 48 ohm. No verified drop-in substitute was identified for this part, so generic multiplexers should not be treated as replacements. Request a cross-reference review through the Request a Quote form on this page.
Is the MAX14803CXB+T the same as a generic 16-channel SPST mux?
No, a generic 16-channel SPST mux is not necessarily the same as the MAX14803CXB+T. A valid substitute must also match the CXB footprint, control logic, supported voltage range, switching timing, leakage, channel capacitance, and the manufacturer’s special pin assignments. Use the Request a Quote form on this page to request a compatibility check for a specific candidate.
When should I choose the MAX14803CXB+T?
Choose the MAX14803CXB+T when the design requires 16 SPST signal paths, a 1:1 configuration, and approximately 48 ohm on-resistance in the specified package. It is especially relevant to instrumentation and test systems that share downstream signal-processing circuitry. Confirm the exact control interface and electrical limits in the manufacturer datasheet before finalizing the schematic.
Is MAX14803CXB+T suitable for industrial test equipment?
The MAX14803CXB+T is suitable for industrial test equipment when its 16-channel SPST architecture and 48 ohm on-resistance meet the measurement system’s requirements. Its switching method can reduce the number of analog connections reaching amplifiers, data converters, or acquisition hardware. Validate signal range, isolation, timing, and common-mode compatibility against the manufacturer datasheet.
How does MAX14803CXB+T compare with a mechanical switch?
The MAX14803CXB+T provides 16 electronically controlled SPST paths with 48 ohm on-resistance, whereas a mechanical switch may offer lower resistance but slower operation and greater mechanical wear. The integrated device supports compact multiplexing and repeatable digital control. Choose it when multi-channel routing and system size matter more than achieving near-zero insertion resistance.
What is the best Analog Devices equivalent for MAX14803CXB+T?
The best equivalent must be an Analog Devices or Maxim Integrated device with the same CXB footprint, pin-to-pin SPST assignments, 16-channel switching capability, and comparable electrical limits. No cross-brand or same-brand drop-in MPN was confirmed by the available component records. Use the Request a Quote form on this page to submit a candidate for engineering review rather than fitting a package merely by name.
Where to buy MAX14803CXB+T online?
The MAX14803CXB+T can be sourced through the Request a Quote form on this product page. Submit the exact MPN, target quantity, and required packaging to request current commercial availability, delivery information, and a formal quotation. The +T suffix denotes the tape-and-reel ordering configuration.
What is the price of MAX14803CXB+T?
Current commercial pricing for the MAX14803CXB+T is handled through the Request a Quote form on this page. Request the exact MPN and quantity so the quotation reflects the correct CXB tape-and-reel configuration and current supply. Buyers should compare the returned commercial terms against their production schedule and target annual usage.
What is the lead time for MAX14803CXB+T?
The current lead time and available production quantity should be requested through the Request a Quote form on this page. Include the required quantity, target delivery date, and whether partial shipments are acceptable. The MAX14803CXB+T ordering code includes the +T tape-and-reel suffix, which helps the quotation identify the correct shipping format.
Is MAX14803CXB+T in stock?
Current stock status should be confirmed through the Request a Quote form on this page rather than inferred from a product listing. Include the required quantity and target delivery date when requesting availability for the MAX14803CXB+T. For production planning, ask for the manufacturer’s expected lead time and any minimum-order quantity associated with the CXB package.
Does MAX14803CXB+T meet RoHS and AEC-Q100 requirements?
RoHS, REACH, and AEC-Q100 status must be confirmed from the current manufacturer product documentation before using the MAX14803CXB+T in a regulated design. The confirmed functional parameters are 16 circuits, 1:1 SPST switching, 48 ohm on-resistance, and tape-and-reel packaging. Request material compliance documentation through the Request a Quote form for the exact ordering code.

Impormasyon ng Talumpati sa Engineering for MAX14803CXB+T — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the MAX14803CXB+T when the design needs 16 SPST switching circuits, a 1:1 configuration, and 48 ohm on-resistance in the specified CXB package. It is particularly suitable for compact test, measurement, data-acquisition, and industrial routing systems where multiple analog paths can share downstream circuitry. Before committing, verify the manufacturer’s absolute maximum ratings, recommended control levels, signal-voltage range, leakage, switching time, and operating temperature limits. A replacement should be considered only when it preserves the footprint, pin functions, and critical electrical behavior. No verified drop-in alternative was identified, so selecting a generic 16-channel multiplexer based only on channel count or SPST terminology would create unnecessary design risk. For regulated production, request current material-compliance documentation and a part-specific supply statement for the exact MAX14803CXB+T ordering code.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto
Circuit Count 16 circuits
Switch Configuration 1:1
Switch Type SPST
On-Resistance 48 ohm
Brand Maxim Integrated

Talaan ng Disenyo

Include the 48 ohm on-resistance in the complete source-switch-load network rather than treating it as an isolated component value. Calculate the resulting voltage division with the actual source and load impedances, then verify settling and bandwidth requirements. If the selected channel drives a high-impedance amplifier, assess leakage and capacitance effects as well.

Route switched signals using short traces and a continuous ground reference to minimize coupling between the 16 channels. Keep connector and protection-network connections away from control traces where practical. Before routing the PCB, verify the CXB land pattern, pin numbering, exposed-pad requirements, and no-connect instructions in the manufacturer package drawing.

Do not select a replacement solely because it is described as a 16-channel SPST mux. A drop-in device must match the CXB footprint, pin assignments, control levels, signal limits, switching timing, leakage, and package tolerances. Confirm the complete ordering suffix and tape-and-reel orientation during component procurement and incoming inspection.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

Material-compliance status was not confirmed for the exact MAX14803CXB+T ordering code. Request the current manufacturer declarations before release to RoHS-, REACH-, or automotive-controlled production.

Data napatotohanan sa: 2026-11-09 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MAX14803CXB+T datasheet MAX14803CXB+T datasheet pdf MAX14803CXB+T pinout MAX14803CXB+T specifications MAX14803CXB+T equivalent MAX14803CXB+T replacement MAX14803CXB+T cross reference MAX14803CXB+T footprint Maxim MAX14803CXB+T MAX14803CXB+T price MAX14803CXB+T stock MAX14803 16-channel SPST mux MAX14803 48 ohm switch MAX14803 test equipment application

Mga kaugnay na Mga Komponente at mga Tuntunin

Maxim Integrated Analog Devices MAX14803CXB+T MAX14803 analog switch IC multiplexer SPST switch single-pole single-throw 16-circuit switch 1:1 switch configuration 48 ohm on-resistance on-resistance signal attenuation source impedance load impedance multiplexing test and measurement data acquisition industrial control surface mount tape and reel RoHS REACH AEC-Q100
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ