MAX202CDRE4 - 5V Dual RS-232 Transceiver | Texas Instruments
Teilenummer: MAX202CDRE4 ✓ AktivMAX202CDRE4 Übersicht
An RS-232 transceiver is an interface IC that bridges a logic-level digital system and a single-ended, bipolar serial bus. Its driver section converts TTL or CMOS logic levels into RS-232 levels, while its receiver section converts RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, the MAX202CDRE4 belongs to the interface-IC class, specifically the RS-232 line-driver and receiver family.
Key features include a 5 V operating supply, support for communication rates up to 120 kbit/s, four integrated charge-pump voltage converters, and ±15 kV human-body-model ESD protection. The bus-side pins meet or exceed TIA/EIA-232-F and ITU V.28 requirements. Shutdown behavior and exact supply-current limits should be confirmed against the manufacturer datasheet before finalizing a power budget.
The internal charge-pump architecture allows the device to operate without a separate ±12 V supply. This reduces external power infrastructure and board complexity compared with discrete RS-232 driver and receiver implementations. The trade-off is that charge-pump circuitry and line-driver stages dissipate power in the interface, so the final thermal design should account for the selected data rate, load, supply voltage, and ambient temperature.
Typical applications include industrial serial-port interfaces, point-of-sale equipment, data-acquisition systems, instrumentation, and embedded control systems. A system designer can connect the MAX202CDRE4 between a microcontroller or host processor with UART logic I/O and an isolated or non-isolated RS-232 connector. External protection, grounding, and isolation remain important when the cable leaves the equipment enclosure.
For PCB implementation, place all four 0.1 µF charge-pump capacitors close to their designated pins and route RS-232 outputs away from sensitive clock and analog signals. Keep the connector interface and transceiver on the same ground reference when using a non-isolated implementation. Confirm pin orientation, exposed supply requirements, and unused-pin treatment using the manufacturer pin-description table.
This page combines device specifications, verified source links, drop-in replacement analysis, application guidance, and package-aware design considerations to support faster component selection and PCB implementation for 5 V RS-232 interfaces.
Drop-in-Alternativen für MAX202CDRE4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX202CDRE4 (gleiche Bauform und Footprint) – abweichend in Package.
ST202CDR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ST202BDR
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX202CDRE4 Technische Daten
| Product Type | Dual RS-232 line driver and receiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Versorgungsspannung | 5 V |
| Maximum Data Rate | 120 kbit/s |
| ESD Protection | ±15 kV human-body model |
| External Capacitors | 4 × 0.1 µF |
| RS-232 Standard Compliance | TIA/EIA-232-F and ITU V.28 |
| Gehäuse | 16-pin SOIC, 3.90 mm width |
| Terminal Count | 16 |
| Montageart | Surface mount |
| Temperature Grade | Commercial |
MAX202CDRE4 16-pin soic, 3.90 mm width Pinbelegungsleitfaden
Pinbelegung für MAX202CDRE4 (16-pin soic, 3.90 mm width-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX202CDRE4.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX202CDRE4 ist geeignet für 6 Anwendungs: Industrial UART Serial Interface, Point-of-Sale Terminal Interface, Instrumentation and Test Equipment, Embedded Control and Data Acquisition, Serial Network Maintenance Port, RS-232 Communication Adapter.
Industrial UART Serial Interface
The MAX202CDRE4 fits industrial controller and data-acquisition equipment that must translate host UART logic into RS-232 levels. Its two drivers and two receivers support bidirectional communication, while operation from one 5 V rail avoids a separate negative supply. The 120 kbit/s capability is appropriate for many legacy serial devices, but cable length, connector wiring, and grounding must be checked. Place the four 0.1 µF capacitors close to the charge-pump pins and provide suitable protection at an exposed connector.
Empfohlen
Point-of-Sale Terminal Interface
The MAX202CDRE4 can connect a point-of-sale controller or peripheral to a legacy RS-232 port using only a 5 V system supply. Two drivers allow command or status transmission, and two receivers support incoming device data. Its ±15 kV human-body-model ESD protection strengthens the bus interface, although it does not replace surge protection for cables extending beyond the enclosure. The 16-pin SOIC also permits a compact layout beside the connector and UART circuitry.
Empfohlen
Instrumentation and Test Equipment
The MAX202CDRE4 is useful in laboratory and industrial instrumentation that must exchange data with RS-232 test equipment. A single 5 V supply simplifies system power architecture, and the 120 kbit/s limit accommodates common serial-control and data-transfer rates. Because the bus uses bipolar signaling, maintain the intended ground reference and avoid routing the RS-232 traces as if they were low-voltage UART signals. Use short, properly terminated charge-pump connections and follow the manufacturer layout for reliable transient behavior.
Empfohlen
Embedded Control and Data Acquisition
The MAX202CDRE4 can bridge a microcontroller UART and an RS-232-equipped sensor, controller, or service port. The 5 V supply operation is convenient for embedded systems that already regulate a 5 V rail, while the dual-channel arrangement allows two RS-232 links in one package. Ensure the microcontroller's logic levels meet the MAX202 input thresholds and that the receiver outputs remain compatible with its supply. Firmware should account for the practical limitations imposed by cable capacitance and connected-device loading.
Empfohlen
Serial Network Maintenance Port
The MAX202CDRE4 is appropriate for a network-device maintenance shell that exposes an RS-232 console through a dedicated connector. The 120 kbit/s rate is more than sufficient for terminal sessions, configuration commands, and diagnostic logs. The device's documented ESD protection is valuable at an accessible connector, but proper chassis grounding and cable-routing practices remain important. A production design should also evaluate whether the service interface needs galvanic isolation rather than a direct ground-coupled MAX202 connection.
Empfohlen
RS-232 Communication Adapter
The MAX202CDRE4 can serve as the core of a compact RS-232 communication adapter for legacy printers, scales, meters, or laboratory devices. Its integrated charge pumps produce RS-232-compatible line levels from one 5 V supply, while two drivers and two receivers provide flexible channel allocation. The design must follow the datasheet capacitor connections and maintain pin-compatible routing with any selected replacement. Verify baud rate, logic thresholds, and connector signal assignments before releasing an adapter intended for field deployment.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX202CDRE4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ST202CDR | ST202BDR |
|---|---|---|---|
| Package | 16-pin SOIC, 3.90 mm width | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | STMicroelectronics | STMicroelectronics |
| Device Type | 2/2 RS-232 transceiver | 2-driver, 2-receiver RS-232 transceiver | 2-driver, 2-receiver RS-232 transceiver |
| Supply Voltage | 5 V | 5 V | 5 V |
| Number of Drivers | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 |
Wichtigste Unterscheidungsmerkmale
- Documented ESD protection for exposed RS-232 connectors (vs. ST202CDR)
- Established 120 kbit/s operating capability (vs. ST202BDR)
- Single-supply implementation with external 0.1 µF charge-pump capacitors (vs. ST202CDR)
Designhinweise
Place the four required 0.1 µF charge-pump capacitors directly between their specified device pins and ground. Keep these loops compact to minimize switching-loop area and transient coupling into adjacent UART or analog signals. Route the MAX202CDRE4 ground connection to the same ground system used by the external capacitors, and consult the manufacturer layout example before duplicating the design on a new PCB.
Separate the RS-232 bus conductors from sensitive clock, sensor, and communication traces. Driver outputs are bipolar and can create larger transition amplitudes than TTL signals, so avoid routing them beneath sensitive analog nodes or parallel to long digital buses. Maintain the intended ground reference for a non-isolated RS-232 design and assess whether an isolated interface is required when the connected equipment has a different earth potential.
Do not treat the MAX202CDRE4 as a TTL UART level translator. Its driver inputs and receiver outputs operate at logic levels, while the external bus pins use RS-232 bipolar signaling. Verify the complete pin description, especially charge-pump capacitor connections and supply pins, against the Texas Instruments datasheet. Also avoid assuming that the documented ±15 kV human-body-model ESD rating eliminates the need for external surge and cable protection.
The charge-pump and driver stages dissipate power during operation. Check the manufacturer supply-current and driver-load specifications, then estimate worst-case dissipation from the actual supply voltage, data activity, termination, and ambient temperature. Provide adequate copper around the 16-pin SOIC and maintain unobstructed airflow when the transceiver is mounted near a power converter or another heat-generating component in a sealed enclosure.
Compliance-Informationen
The component is described as commercial grade. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited source data, so those fields remain unknown.