MAX202ESE-TG068 - 5V RS-232 Transceiver | Analog Devices
Teilenummer: MAX202ESE-TG068 ✓ AktivMAX202ESE-TG068 Übersicht
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential, bipolar RS-232 signals. It belongs to the line-driver and line-receiver hierarchy, within interface ICs and communication semiconductors. Unlike TTL or CMOS serial links, RS-232 defines voltage levels, driver impedance, and receiver behavior for reliable point-to-point data transfer over longer cables.
The MAX202 family combines integrated drivers, receivers, and an on-chip charge pump in one package. The TG068 ordering code identifies a specific package, temperature, and marking configuration of the MAX202ESE device. Key characteristics include two RS-232 drivers, two RS-232 receivers, 5 V single-supply operation, 16-pin SOIC packaging, and external 0.1 uF charge-pump capacitors. The manufacturer product page describes operation above 120 kbps while maintaining the specified plus or minus 5 V output levels.
The charge-pump architecture allows the MAX202 to generate the positive and negative RS-232 voltages required by the interface from a single 5 V supply. Its integrated drivers include slew-rate control for reducing transmission glitches, while the receivers use the differential voltage thresholds defined for EIA/TIA-232E. Because the external capacitors establish the charge-pump operating point, their type, voltage rating, tolerance, and placement directly affect interface performance.
Typical uses include industrial serial consoles, instrumentation links, point-of-sale equipment, data acquisition systems, and service interfaces where a host must exchange RS-232 data with a peripheral over a shielded cable. The device is also useful in legacy equipment upgrades, test fixtures, and embedded control panels that retain an RS-232 physical interface while adding modern logic internally.
For PCB design, place the 0.1 uF charge-pump capacitors close to their corresponding pins, route the RS-232 driver outputs away from sensitive receiver inputs, and provide a controlled reference ground near the connector. Verify the interface level and connector gender before assembly because RS-232 links commonly require crossover wiring. Use the manufacturer pin-description table and the MAX202 datasheet for the authoritative signal assignment.
Drop-in-Alternativen für MAX202ESE-TG068 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX202ESE-TG068 (gleiche Bauform und Footprint) – abweichend in Package, Supply Voltage, Product Type, ESD Protection, External Charge-Pump Capacitor.
MAX202ESE+
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX202ESE+T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX202ESE-C78046
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX202ECSE+TG068
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX202EESE+
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX202ESE-TG068 Technische Daten
| Device Type | RS-232 transceiver |
| Channel Configuration | 2 driver / 2 receiver |
| Versorgungsspannung | 5 V |
| Datenrate | In excess of 120 kbps |
| RS-232 Output Signal Levels | Plus or minus 5 V |
| Interface Standard | EIA/TIA-232E |
| External Charge-Pump Capacitor | 0.1 uF |
| Gehäuse | 16-pin SOIC |
| Montageart | Surface mount |
| Transceiver Type | Full-duplex |
| RoHS-Status | RoHS |
MAX202ESE-TG068 16-pin soic Pinbelegungsleitfaden
Pinbelegung für MAX202ESE-TG068 (16-pin soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX202ESE-TG068.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX202ESE-TG068 ist geeignet für 6 Anwendungs: Industrial Serial Console Interface, Data Acquisition Equipment Communication, Point-of-Sale Terminal Connectivity, Test and Measurement Fixture Control, Legacy Equipment Retrofit and Upgrade, Service and Configuration Port.
Industrial Serial Console Interface
The MAX202ESE-TG068 fits industrial console designs that require a conventional RS-232 port for configuration, diagnostics, or service access. Its two drivers and two receivers provide full-duplex communication from a 5 V logic rail, while the documented data rate in excess of 120 kbps supports console protocols and moderate-rate diagnostic transfers. The integrated charge pump eliminates a separate negative supply, and the 16-pin SOIC footprint simplifies placement on dense controller boards. Place the required 0.1 uF capacitors adjacent to the charge-pump pins and keep the bipolar driver traces away from sensitive receiver inputs to minimize coupling.
Empfohlen
Data Acquisition Equipment Communication
The MAX202ESE-TG068 is appropriate for data acquisition systems that expose a legacy RS-232 command or telemetry port to a host controller. The two-channel arrangement allows simultaneous command transmission and response reception, and operation in excess of 120 kbps is suitable for moderate-rate measurement data and status polling. Because the device generates the required bipolar RS-232 levels from one 5 V supply, instrumentation can avoid a separate negative rail. Keep the connector-side interface isolated from sensitive analog measurement paths, and verify the shield and reference-ground strategy to reduce ground-potential errors between the instrument and the host computer.
Empfohlen
Point-of-Sale Terminal Connectivity
Retail peripherals such as receipt printers, scanners, and customer displays often retain an RS-232 port even when their internal controller is modern. The MAX202ESE-TG068 provides the required driver and receiver functions in one 16-pin SOIC package, with a documented throughput in excess of 120 kbps for short transactional exchanges. Its integrated charge pump minimizes external power-conversion circuitry, while the small surface-mount package leaves board area for the host processor and connectors. Confirm the peripheral's driver and receiver enable logic, and use crossover wiring where required by the standard D-sub connector assignments.
Empfohlen
Test and Measurement Fixture Control
The MAX202ESE-TG068 can be used in automated test fixtures where a controller commands legacy instrumentation through RS-232. Two drivers and two receivers support full-duplex exchanges such as command output followed by measurement-data retrieval, and the specified rate in excess of 120 kbps is adequate for many instrument control protocols. Integrating the charge pump in the package reduces fixture complexity compared with discrete negative-rail generation. Keep the transceiver close to the connector, provide a continuous ground reference, and consider adding series impedance or filtering when cable reflections or electrostatic-discharge events threaten interface reliability.
Empfohlen
Legacy Equipment Retrofit and Upgrade
The MAX202ESE-TG068 is useful when modernizing a controller board that must retain an RS-232 connector for older machinery. A single 5 V supply powers the transceiver and its charge pump, reducing the number of rails required compared with a discrete bipolar driver design. The two-driver, two-receiver arrangement supports bidirectional communication over one RS-232 port, and the 16-pin SOIC package is straightforward to route on an updated PCB. Confirm whether the legacy equipment uses a D-sub connector with DB9 or DB25 assignments, because mechanical gender and signal crossover must be checked independently of the electrical transceiver choice.
Empfohlen
Service and Configuration Port
The MAX202ESE-TG068 can serve as the service interface for embedded equipment, allowing a technician to connect a laptop or maintenance terminal for firmware loading, configuration changes, and fault logging. The two-driver, two-receiver structure supports interactive command sessions, while data rates in excess of 120 kbps provide ample margin for common serial console traffic. The integrated charge pump and external 0.1 uF capacitors allow a compact implementation on an SMD assembly. Place the interface connector near the transceiver, use a grounded shield where required, and protect externally accessible lines against electrostatic-discharge events.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX202ESE-TG068 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX202ESE | MAX202ESE+T | MAX202ESE-C78046 | MAX202ECSE+TG068 | MAX202EESE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Device Type | RS-232 transceiver | MAX202-family RS-232 transceiver | MAX202-family RS-232 transceiver | MAX202-family RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver |
| Channel Configuration | 2 driver / 2 receiver | 2 driver / 2 receiver | 2 driver / 2 receiver | 2 driver / 2 receiver | 2/2 full RS-232 | 2/2 full RS-232 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Data Rate | In excess of 120 kbps | In excess of 120 kbps | In excess of 120 kbps | In excess of 120 kbps | In excess of 120 kbps | In excess of 120 kbps |
| Output Signal Levels | Plus or minus 5 V | Plus or minus 5 V | Plus or minus 5 V | Plus or minus 5 V | Plus or minus 5 V | Plus or minus 5 V |
| External Charge-Pump Capacitor | 0.1 uF | 0.1 uF | 0.1 uF | 0.1 uF | 0.1 uF | 0.1 uF |
| RoHS Status | RoHS | RoHS | RoHS | RoHS | RoHS | RoHS |
Wichtigste Unterscheidungsmerkmale
- Direct TG068 ordering configuration (vs. MAX202ESE)
- Documented high-speed bipolar output capability (vs. MAX202ECSE+TG068)
- Integrated charge pump with only 0.1 uF external capacitors (vs. MAX202EESE+)
Designhinweise
Place the two required 0.1 uF charge-pump capacitors as close as practical to their designated pins. Keep capacitor and charge-pump current paths compact because long loops can radiate noise into nearby analog or high-impedance nodes. Select low-ESL ceramic capacitors with a DC voltage rating appropriate for the charge-pump rails, and follow the capacitor layout and connection guidance in the MAX202 datasheet.
Route the two RS-232 driver outputs directly toward the connector and keep them separated from receiver inputs and other sensitive traces. Maintain the specified receiver input impedance and termination arrangement to avoid loading the bipolar signal. If the cable is long or the enclosure ground potential differs, verify the common-mode voltage and use the connector shield as a shield rather than a signal return.
Do not assume every MAX202 orderable MPN has identical temperature, packaging, or marking attributes even when the pin count matches. Compare the MAX202 datasheet ordering table for MAX202ESE-TG068, MAX202ESE, MAX202ECSE+TG068, and MAX202EESE+ before substitution. Also confirm DB9 or DB25 connector gender and crossover requirements; a pin-compatible IC does not remove the possibility of an incorrect cable or reversed signal assignment.
The charge-pump converter can produce periodic current transitions on the 5 V rail. Place local supply-decoupling capacitance at the device and keep the charge-pump loop confined to the IC and its two external capacitors. If the RS-232 port shares a board with sensitive analog measurement circuitry, route the connector and driver section toward the board edge and observe the interface's emissions and susceptibility performance during system verification.
Compliance-Informationen
The MAX202ESE-TG068 product listing identifies RoHS status. Other compliance declarations were not established from the available manufacturer or distributor records and require confirmation for the exact ordering code.